Electromagnetic interference shielding effectiveness of MWCNT filled poly(ether sulfone) and poly(ether imide) nanocomposites

Multiwalled carbon nanotube (MWCNT) filled poly(ether sulfone) (PES) and poly(ether imide) (PEI) composites were prepared with different MWCNT weight fractions (0.5–5wt%) by a solution mixing technique. Their electrical conductivities, electromagnetic interference (EMI), shielding effectiveness (SE), return loss (RL), and absorption loss (AL) were investigated. Morphologies of the fracture surfaces of nanocomposites studied by scanning electron and transmission electron microscopy showed relatively good MWCNT dispersion and distribution. The electrical conductivity of compression molded samples measured at room temperature indicated that the electrical percolation network was achieved already at 0.5% loading. The measurements of shielding effectiveness (SE) carried out in the frequency range of 8 to 12 GHz (X‐band range) showed that SE increases with measurement frequency and with filler loading, whereby no significant differences could be observed between PES and PEI as matrices. The nanocomposites based on both matrices with 5 wt% loading of MWCNT exhibited shielding levels at 8 GHz between 42 and 45 dB in comparison with the pure polymers which showed value in the range of 1 to 2 dB. RL and AL showed significantly lower values for the composites as compared to unfilled polymers, but no systematic trends were observed on frequency. POLYM. ENG. SCI., 54:2560–2570, 2014. © 2013 Society of Plastics Engineers     

Data Preprocessing of In Situ Laser‐Backscattering Measurements

In situ measurement techniques are promising tools to aid process development. However, they also pose new challenges in evaluating large amounts of recorded data. A new procedure for in situ laser‐backscattering devices has been developed that allows transformation of the raw recorded data, a chord length distribution, into a format suitable for population balance modeling. Emphasis is thereby laid on the influence of the suspension density on the measured data. Experimental data are recorded using a batch laboratory crystallizer equipped with an in situ 3D‐ORM laser backscattering device and an ultrasound probe. The new proposed five‐step procedure for data preprocessing is based on several independently developed tools from literature and is exemplarily illustrated with results on the crystallization of ascorbic acid. The proposed method is a step forward to use in situ laser‐backscattering devices also for quantitative purposes.     

Untersuchungen zur Ursache der Tropfenkondensation von Wasserdampf an ionenimplantierten Metalloberflächen

The origin of dropwise condensation of steam on ion implanted metallic surfaces was fundamentally studied. Condensation experiments and surface analyses showed that chemically inhomogeneous surfaces with topographic microstructures are likely to induce dropwise condensation. These surface characteristics are caused by particulate precipitates. Such particles are formed on ion implanted surfaces by the degradation of the material supersaturation with the doping elements. Similar surfaces showing dropwise condensation also emerged spontaneously on several unimplanted, high‐alloyed materials due to oxidation and erosion effects induced by the condensation process. For explaining the observed condensation phenomena on the identified surface characteristics, a new model for the condensation mechanism was developed.     

Polyether Cyclization Cascade Alterations in Response to Monensin Polyketide Synthase Mutations

The targeted manipulation of polyketide synthases has in recent years led to numerous new-to-nature polyketides. For type I polyketide synthases the response of post-polyketide synthases (PKS) processing enzymes onto the most frequently polyketide backbone manipulations is so far insufficiently studied. In particular, complex processes such as the polyether cyclisation in the biosynthesis of ionophores such as monensin pose interesting objects of research. We present here a study of the substrate promiscuity of the polyether cyclisation cascade enzymes in monensin biosynthesis in the conversion of redox derivatives of the nascent polyketide chain. LC-HRMS/MS²-based studies revealed a remarkable flexibility of the post-PKS enzymes. They acted on derivatized polyketide backbones based on the three possible polyketide redox states within two different modules and gave rise to an altered polyether structure. One of these monensin derivatives was isolated and characterized by 2D-NMR spectroscopy, crystallography, and bioactivity studies.     

Reinforced chloroprene rubber by in situ generated silica particles: Evidence of bound rubber on the silica surface

Nano silica is generated in situ inside the uncrosslinked chloroprene rubber (CR) by the sol‐gel reaction of tetraethoxysilane (TEOS). This results in appreciable improvement in mechanical properties of the CR composites at relatively low filler content. Furthermore, exploitation of reactive organosilanes, γ‐aminopropyltrimethoxysilane (γ‐APS) in particular, in the silica synthesis process facilitates growing of spherical silica particles with a size distribution in the range of 20‐50 nm. The silica particles are found to be uniformly dispersed and they do not suffer from filler‐filler interaction. Additionally, it is observed that the silica particles are coated by silane and rubber chains together which are popularly known as bound rubber. The existence of the bound rubber on silica surface has been supported by the detailed investigations with transmission electron microscopy (TEM), energy filtered transmission electron microscopy (EFTEM) and energy dispersive X‐ray spectroscopy (EDAX). The interaction between rubber and silica, via bi‐functionality of the γ‐APS, has been explored by detailed FTIR studies. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43717.     

Processing, Microstructure, and Properties of Laminated Silicon Nitride Stacks

By lamination of silicon nitride tapes, components with complex geometries can be produced. Unstructured tapes can be laminated by common thermal compression. Structured tapes, however, have to be joined by pressureless processes using e.g. pastes as lamination aids because deformation of the structures would occur. These pastes usually contain a binder for maintaining the mechanical contact between the tapes during processing. To prevent the high mass loss of typical organic binders during burnout, pre-ceramic polymers were used in this work. These ceramic precursors convert partly into an inorganic material during heat treatment with a significant reduced mass loss compared with common organic binders. Thus, the porosity in the interlayer of a laminated stack is strongly decreased, which should be favorable for the mechanical and thermal properties. This work discusses the resulting microstructure, strength, and thermal diffusivity data of stacks laminated with pastes containing various precursor contents. These results are compared with those obtained by samples prepared by compression of green tapes. It is found that except for some large pores, the microstructure of the precursor-derived interlayers is qualitatively the same as in the tape material. For stacks made by both lamination methods, strength measurements reveal that the properties parallel and perpendicular to the layers are different. It is shown that the same strength level can be obtained both by using the pressureless route and by the compression method. Unlike the strength, the thermal conductivity does not change with the direction of measurement.     

Deformation and orientation behavior of polystyrene-b-polybutadiene-b-poly(methyl methacrylate) triblock terpolymers: Influence of polybutadiene microstructures and the molar masses

Morphological changes caused by deformation and orientation of different domains of polystyrene-b-polybutadiene-b-poly(methyl methacrylate), SBM, triblock terpolymers were investigated using in-situ small angle X-ray scattering (SAXS), tensile testing, and transmission electron microscopy (TEM). Two sets of SBM triblock terpolymers with similar weight fractions of the three blocks were studied. The two sets differ in terms of their molecular weights. Each set contained two SBM differing in their polybutadiene isomers (1,2- and 1,4-B). Results showed that for 1,2-B based SBMs the polybutadiene block forms cylindrical domains which coalesce in the glassy lamellar matrix of the two glassy outer blocks whereas the lower molar mass 1,4-B based SBM forms mixed S/M and the higher one forms well segregated long range ordered lamellae. These morphological differences indicate that the deformation and the orientation behavior of the polymers' domains differ. In 1,2-B based SBMs yielding at high stresses was followed by a stress drop after the yield point. The other polymer type showed homogeneous deformation of the lamellar domains at their yield point. 2D-SAXS during deformation of the triblock terpolymers showed an anisotropic deformation pattern in the 1,2-B SBMs, whereas four point SAXS patterns were found for the 1,4-B SBMs. Further studies showed that the fragmented lamellar planes of the lower molar mass 1,2-SBM oriented randomly whereas the orientation of the lamellar planes of the higher molar mass 1,2-B SBM was parallel to the strain direction. The alignment of the lamellar planes of 1,4-B SBMs were randomly distributed in the unstretched state.     

On the interrelationship of transreaction with viscoelastic properties of poly(ethylene terephthalate)/poly(ethylene naphthalate) blends in the presence of nanoclay

An attempt was made to explore the effects of the interchange reactions on the viscoelastic behavior of binary blends based on poly(ethylene terephthalate) (PET)/poly(ethylene naphthalate) (PEN) and their nanocomposites. It was seen that with an increase in the number of extrusion runs and mixing temperature, the extent of reaction (X) and degree of randomness (RD) both increased, whereas the average sequence block lengths values were decreased. On the contrary, the blend composition did not play a significant role on X and RD values. Addition of nanoclay inhibited the transreactions in PET/PEN blends. The absence of crystallization peaks implied that the crystalline structure was destroyed as a result of blending and an amorphous system was created possibly due to the transreactions simultaneously with the formation of random copolymers inhibiting the crystallization process. The rheological investigations showed that the addition of PEN into the PEN/PET blends enhanced the storage modulus, loss modulus, and complex viscosity. The viscosity upswing observed at low‐frequency region in the case of nanocomposite systems evidently confirmed the occurrence of transreactions. Nonetheless, a significant increment in the viscoelastic properties was perceived in the presence of nanoclay corroborating the proper nanoclay distribution throughout the PET/PEN blend system. POLYM. ENG. SCI., 53:2556–2567, 2013. © 2013 Society of Plastics Engineers