Electrochemical Faceting of polycrystalline platinum in HF solutions

The electrochemical faceting of polycrystalline (pc) platinum yielding a (100)-preferred oriented electrode surface was accomplished in HF solutions by applying to the pc platinum electrode a square wave potential perturbation at 1 kHz in the 0.2 to 1.3 V range (vs rhe). SEM patterns of the resulting surfaces were also obtained. For HF concentrations up to 2 M no appreciable influence of the electrolyte concentration on the electrochemical faceting was noticed. Otherwise, the voltammetric response of the (100)-type preferred oriented platinum surface in the H-adatom potential range when compared to previously reported data resulted remarkably sensitive to the electrolyte composition. The discussion of results was based on the non-equilibrium adsorption conditions for anions under the periodic perturbation.     

解放思想 加快发展 开创胶鞋行业新局面

2008年6月，温家宝总理在省区市和中央部门主要负责同志会议上指出：今年以来，我国经济社会发展经受了最为严峻的重大挑战和考验。这也让我们更加关注企业生存和发展的国际国内环境。     

中橡协力车胎分会召开第十五次会员大会

中国橡胶工业协会力车胎分会4月15～16日在青岛市召开了第十五次会员大会，大会总结了第六届理事会工作，讨论并通过推荐第七届理事和总会理事名单、副理事长和总会常务理事名单，确认了分会理事长、秘书长。讨论通过了第七届理事会工作设想及安排。     

我国工程机械现状及今后发展趋势

中国的工程机械行业建立于1961年。改革开放以后，由于国内对工程机械的需求量大，自1978年开始至20世纪末共引进近200项技术．发展了近500个新产品。使我国的工程机械迈上了一个新的台阶，当年引进的产品目前已成为我国工程机械的主导产品。     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

Epoxy paint failure in B-52 fuel tanks: Part II. Influence of DIEGME concentration in the fuel on the failure process

A model has been proposed to explain the failure of the original BMS10-39 epoxy paint on upper vertical surfaces in B-52 fuel tanks. The model involves interaction of the paint with DIEGME, a fuel system ice inhibitor (FSII) in jet fuel, that is distilled from the liquid fuel. In this communication, distillation experiments used to support the model are refined to better match the mass transfer of vapor from fuel in a B-52 fuel tank at close to room temperature. The interaction of these lower temperature distillates with the paint affirms the earlier model. On the basis of these experiments it is proposed that paint failure may be controlled or eliminated by reducing the level of DIEGME in the fuel. Proposed changes in military jet fuel composition are detailed.     

Integration of prior knowledge of measurement noise in kernel density classification

Samples can be measured with different precisions and reliabilities in different experiments, or even within the same experiment. These varying levels of measurement noise may deteriorate the performance of a pattern recognition system, if not treated with care. Here we seek to investigate the benefit of incorporating prior knowledge about measurement noise into system construction. We propose a kernel density classifier which integrates such prior knowledge. Instead of using an identical kernel for each sample, we transform the prior knowledge into a distinct kernel for each sample. The integration procedure is straightforward and easy to interpret. In addition, we show how to estimate the diverse measurement noise levels in a real world dataset. Compared to the basic methods, the new kernel density classifier can give a significantly better classification performance. As expected, this improvement is more obvious for small sample size datasets and large number of features.     

Secondary Aluminum Production Waste — A Raw Material for the Refractory Industry

Secondary aluminum waste products, and processes that occur during heating and mineral formation on introducing fine periclase powder into the composition of waste products are studied. It is demonstrated that secondary aluminum production waste may be used as a raw material for synthesizing aluminomagnesia spinels. Translated from Novye Ogneupory, No. 6, pp. 15–18, June 2008.     

Testing a new composition of periclase spinel objects

On the basis of periclase powder (70%) and aluminomagnesia spinel (30%), synthesized from secondary aluminum production waste and caustic magnesite, test objects are produced of periclase spinel composition satisfying the requirements of GOST 1579-006-00190495-98. The articles are successfully tested in the working layer for lining tunnel furnace cars of OAO Kombinat Magnezit. __________ Translated from Novye Ogneupory, No. 8, pp. 16–17, August 2008.