Crystallographic, thermoelectric, and mechanical properties of polycrystalline type-I Ba8Al16Si30-based clathrates

Crystallographic, thermoelectric, and mechanical properties of polycrystalline Ba₈Al₁₆Si₃₀-based samples with type-I clathrate structure prepared by combining arc melting and spark plasma sintering methods were investigated. The major phase of the samples was a type-I clathrate with an actual Al/Si ratio of ~15/31, strongly suggesting that framework deficiency was absent or was present in very low concentration in the samples. The Hall carrier concentration n of the samples was approximately 1 × 10²¹ cm^?3, which is lower than the values reported so far for the Ba₈Al₁₆Si₃₀ system. Other important material parameters of the samples were as follows: the density-of-states effective mass m* = 2.3m ₀, Hall mobility μ = 7.4 cm² V^?1 s^?1, and the lattice thermal conductivity κ _L = 1.2 W m^?1 K^?1. The thermoelectric figure of merit ZT reached approximately 0.4 (900 K) for a sample with n = 9.7 × 10²⁰ cm^?3. Simulation using the experimentally determined values of material parameters showed that ZT reached values >0.5 if the carrier concentration is optimized at about 3 × 10²⁰ cm^?3. Young’s, shear, and bulk moduli were estimated to be approximately 98, 39, and 117 GPa, respectively, and Poisson’s ratio was found to be 0.25 from the longitudinal and transverse velocities of sound, v _L = 6038 m/s and v _T = 3503 m/s, respectively, for a sample with ZT = 0.4. The coefficient of thermal expansion (CTE) ranged from approximately 8 × 10^?6 K^?1 to 10 × 10^?6 K^?1 (330–690 K), which is smaller than the values reported for Ba₈Ga₁₆Ge₃₀ and Sr₈Ga₁₆Ge₃₀ clathrates.     

Preparation of carbon-supported PtCo nanoparticle catalysts for the oxygen reduction reaction in polymer electrolyte fuel cells by an electron-beam irradiation reduction method

We prepared carbon-supported PtCo bimetallic nanoparticles (PtCo/C) as electrode catalysts for the oxygen reduction reaction (ORR) at the cathodes in polymer electrolyte membrane fuel cells (PEFCs) by an electron-beam irradiation reduction method (EBIRM). An EBIRM allows nanoparticles to be easily prepared by the reduction of precursor ions in an aqueous solution irradiated with a high-energy electron beam. The structures of PtCo/C were characterized by transmission electron microscopy, inductively coupled plasma atomic emission spectrometry, and the techniques of X-ray diffraction and X-ray absorption near edge structure. It found for the first time that both PtCo alloy and Co oxide were prepared simultaneously on the carbon support by an EBIRM. The catalytic activity and durability of PtCo/C were evaluated by linear-sweep voltammetry and cyclic voltammetry, respectively. The addition of Co to Pt/C not only enhanced the catalytic activity for the ORR but also improved the catalytic durability. As the Co concentration increased, both behaviors became pronounced. These improvements are explained by the effects of both PtCo alloy and Co oxide. We demonstrated that an EBIRM can not only synthesize the alloy and oxide simultaneously on the carbon support but also mass-produce the electrode catalysts for PEFC cathodes.     

XPS study of the process of apatite formation on bioactive Ti—6Al—4V alloy in simulated body fluid

Bioactive Ti—6Al—4V alloy, which spontaneously forms a bonelike apatite layer on its surface in the body and bonds to living bone through this apatite layer, can be prepared by producing an amorphous sodium titanate on its surface by NaOH and heat treatments. In this study, the process of apatite formation on the bioactive Ti—6Al—4V alloy was investigated in vitro, by analyzing its surface with X-ray photoelectron spectroscopy as a function of soaking time in a simulated body fluid 4SBF). Thin-film X-ray diffractometry of the alloy surface and atomic emission spectroscopy of the fluid were also performed complementarily. It was found that immediately after immersion in the SBF,the alloy exchanged Na¹ ions from the surface sodium titanate with H₃O¹ ions in the fluid to form Ti-OH groups on its surface. The Ti-OH groups, immediately after their formation,incorporated the calcium ions in the fluid to form calcium titanate. The calcium titanate thereafter incorporated the phosphate ions in the fluid to form an amorphous calcium phosphate, which was later crystallized into bonelike apatite. This process of apatite formation on the alloy was the same as on the pure titanium metal, because the alloy formed the sodium titanate free of Al and V by the NaOH and heat treatments. The initial formation of the calcium titanate is proposed to be a consequence of the electrostatic interaction of negatively charged units of titania dissociated from the Ti-OH groups with the positively charged calcium ions in the fluid. The calcium titanate is postulated to gain a positive charge and interact with the negatively charged phosphate ions in the fluid to form amorphous calcium phosphate, which eventually stabilizes into crystalline apatite.     

Microstructures and fracture toughness of directionally solidified Mo-ZrC eutectic composites

Microstructures and fracture toughness of arc-melted and directionally solidified Mo–ZrC eutectic composites were investigated in this study. Two kinds of directionally solidified composites were prepared by spot-melting and floating zone-melting. Microstructure of the arc-melted composite (AMC) consists of equiaxed eutectic colonies, in which ZrC particles are dispersed. The spot-melted composite (SMC) exhibits spheroidal colony structure, which is rather inhomogeneous in size and morphology. ZrC fibers in the eutectic colonies are aligned almost parallel to the growth direction. Well aligned, homogeneous columnar structure with thin ZrC fibers evolves in the floating zone-melted composite (FZC). Texture measurement by X-ray diffractometry revealed that the growth direction of Mo solid solution (Mo_SS) in FZC is preferentially 〈100〉, while that of SMC is scattered. Fracture toughness K_q evaluated by three point bending test using the single edge notched beam method is >13 MPa m^1/2 for AMC, 20 MPa m^1/2 for SMC and 9 MPa m^1/2 for FZC. Intergranular fracture along colony boundaries is often observed in AMC. In contrast, transgranular fracture is dominant in SMC and FZC, although significant gaps caused by intergranular fracture are occasionally observed in SEM micrographs of SMC. Fracture surface in FZC is wholly flat. Pull-out of ZrC occurs owing to Mo/ZrC interfacial debonding in intergranularly fractured regions of AMC and SMC.

Coarse elongated colonies in SMC and FZC induce transgranular fracture instead of intergranular fracture. Intergranular fracture and interfacial debonding in AMC and SMC causes frequent crack deflection accompanied by ligament formation and crack branching, which is responsible for the high fracture toughness of the composites. Preferred 〈100〉 growth of Mo_SS phase in FZC leads to brittle 〈100〉 cleavage fracture associated with low fracture toughness.     

Thermophysical properties of Th1−xUxO2 pellets prepared by spark plasma sintering technique

Th_1?x U _x O₂ solid solutions were synthesized by solid-state reaction and pelletized using the spark plasma sintering (SPS) technique. Pellets with >90% theoretical density were easily obtained within 40 min of sintering without any additive. The thermal conductivity, Young's modulus, Debye temperature, Vickers hardness, and heat capacity were systematically investigated, and the values for ThO₂ agree with the literature data. The thermal conductivity of Th_1?x U _x O₂ decreased with increasing U content up to x =～0.5. This tendency corresponds to phonon-point defect scattering theory. The Young's modulus and Debye temperature linearly decreased with increasing U content. The Debye temperature and standard molar entropy derived from the low-temperature heat capacity agree with the reported values.     

Fundamentals for Controlling the Microstructure and Properties of Cold Rolled and Continuously Annealed Sheet Steels

The strict control of microstructure is indispensable for meeting the demands for sheet steels with superior properties. This paper reviews the state-of-the-art related to continuous annealing process from the viewpoint of physical metallurgy. For mild steel, control of texture is one of the most important issues ensuring deep drawability. Therefore, the fundamental guiding principles on texture control are reviewed. Heterogeneity in cold rolled structures is discussed, with emphasis placed on grain boundary, shear band and cementite in terms of preferential nucleation of recrystallized grains. Furthermore, C-X interactions in the recovery stage are discussed in conjunction with scavenging effects. The ND//<111> texture usually evolves according to the grain growth, which is enhanced by reducing the pinning effect. The ductility in low-C steels is significantly influenced by the state of C, which implies the importance of C control in the continuous annealing process. As for high strength sheet steels, the basic guiding principles for dual phase and transformation induced plasticity (TRIP) steels are reviewed in terms of phase transformation and TRIP effect. Because the strength of steels currently in practical use is considered to be only a part of their potential, steels are materials with many advantages and technical problems that remain to be solved.     

Impact of oral administration of compost extract on gene expression in the rat gastrointestinal tract

Oral administration of an extract consisting of compost fermented with thermophiles to pigs reduces the incidence of stillbirth and promotes piglet growth. However, the mechanism by which the compost extract modulates the physiological conditions of the animals remains largely unknown. Here, we investigate the effects of compost extract on the physiological responses in the intestine of a mammalian rat model. The level of fecal immunoglobulin A (IgA), which provides protection against pathogens and is secreted from the small intestine, was significantly higher in rats treated with continuous administration of the compost extract than in untreated rats after 2 months, but not after 1 month. However, the fecal IgA level was not significantly different in rats that received the filtered compost extract compared with the untreated rats or the rats that received the compost extract. Gene expression analyses of the small intestine indicated that several immune-related genes were upregulated following compost exposure. Specifically, the expression levels of lymphocyte chemoattractant chemokine CXCL13 and Granzyme B, which is released within cytotoxic T lymphocytes and natural killer cells, increased in the small intestinal tract following compost exposure. Based on these observations, it was postulated that the increased level of fecal IgA following compost exposure was associated with the expression of CXCL13 and Granzyme B in the intestinal tract. Thus, thermophile-fermented compost could contain microbes or substances that activate the rat's gut mucosal immune response.     

Measured Viscous and Dry Friction Forces in Nanometer-Thick Lubricant Film by Friction Force Microscopy with Micromechanical Probe

A new method for measuring the contribution of the local viscous and dry friction forces on the micrometer scale is described. The velocity dependence of the local friction force is obtained using a dual-axis micromechanical probe with an electrostatic actuator. It is used to obtain the local damping coefficient and dry friction force of nm-thick lubricant films patterned on the micrometer scale. This method is useful for clarifying the mechanism of thin-film-based and boundary lubrications.     

Differences in Lipid Characteristics Among Populations: Low-Temperature Adaptability of Ayu, Plecoglossus altivelis

The lipid and fatty acid compositions of the total lipids of three cultured populations (migratory between fresh and salt water, Lake Biwa landlocked, and Setogawa River forms) of ayu, Plecoglossus altivelis, were investigated to clarify the difference in lipid characteristics and temperature adaptability among the three groups. Triacylglycerols were the dominant depot lipids of the three populations, while phospholipids, such as phosphatidylcholine and phosphatidylethanolamine, were found to be the major components of the polar lipids, and their lipid classes are similar to each other. The major fatty acids in the triacylglycerols of all specimens were 16:0, 18:0, 16:1n-7, 18:1n-7, 18:1n-9, 18:2n-6 (linoleic acid), 20:5n-3 (EPA, icosapentaenoic acid), and 22:6n-3 (DHA, docosahexaenoic acid), similar to the tissue phospholipids of the three populations, 16:0, 18:0, 16:1n-7, 18:1n-7, 18:1n-9, 18:2n-6, 20:4n-6, EPA, and DHA. All classes had high levels of 18:2n-6, which originates from their dietary lipids. Compared with the lower DHA levels of the triacylglycerols, the higher levels in the phospholipids suggest their selective accumulation or a biosynthetic pathway to DHA as in freshwater fish. Two populations (the migratory and Setogawa River forms) adapted to lower temperatures with comparatively high levels of polyunsaturated fatty acids (PUFA) for their membrane fluidities. With significantly higher levels of n-3 PUFA and total PUFA, the mean DHA content in the lipids of the Setogawa River form (the population that adapted to lower temperatures) was significantly higher than that of the migratory form. From these results, we concluded that the Setogawa River population actively concentrates long-chain PUFA in its polar lipids and has high adaptability to low temperature.     

Design of a new high repetition rate Nd:YAG Thomson scattering system for Heliotron J

A new high repetition rate Nd:YAG Thomson scattering system has been designed for the Heliotron J helical device. The main purpose of installing the new Thomson scattering system is an investigation of an improved confinement physics such as the edge transport barrier (H-mode) or the internal transport barrier of the helical plasma. The system has 25 spatial points with ～10?mm resolution. Two high repetition Nd:YAG lasers (>550?mJ?at?50?Hz) realize the measurement of the time evolution of the plasma profile with 10 ms time interval. Scattered light is collected with a large concave mirror (D=800?mm,?f/2.25) with a solid angle of ～100?msr. The laser beam is injected from obliquely downward to upward, and obliquely backscattered light is detected (scattering angle is 20°). Model simulation of the polychromator shows the measurable electron temperature and density range are from 10 eV to 10 keV, >5×10(18)?m(-3) within 3% error for the temperature measurement, respectively.