A generation method of artificial fluctuation data of wind power output considering smoothing effect

To use realistic wind power fluctuation data is important in simulating frequency change of power systems. It is well known that the smoothing effect must be taken into account when generating the artificial wind power output. Therefore, this paper proposed a new method to generate fluctuation waveform considering smoothing effect based on random number to fulfill the correlation among multiple sites and autoregression model. The effectiveness of the proposed method was tested by using practical wind speed data measured in Tohoku district.     

Monolithiation of 5,5′‐Dibromo‐2,2′‐bithiophene Using Flow Microreactors: Mechanistic Implications and Synthetic Applications

The lithiation of 5,5′‐dibromo‐2,2′‐bithiophene with one equivalent of an alkyllithium such as n‐BuLi or s‐BuLi was studied by varying the residence time in flow microreactors. With a short residence time, the product 2,2′‐bithiophene (3) derived from dilithiation was obtained preferentially and a significant amount of the starting material 5,5′‐dibromo‐2,2′‐bithiophene remained unchanged. An increase in the residence time caused a higher yield of the product 5‐bromo‐2,2′‐bithiophene derived from monolithiation with expense in the yields of 2,2′‐bithiophene and 5,5′‐dibromo‐2,2′‐bithiophene. The lithiation using MeLi gave the product 5‐bromo‐2,2′‐bithiophene preferentially even with a very short residence time.     

Cathodic pulse breakdown of anodic films on aluminium in alkaline silicate electrolyte – Understanding the role of cathodic half-cycle in AC plasma electrolytic oxidation

Sequential anodic and cathodic pulse voltages were applied on anodised Al micro-electrodes in alkaline silicate electrolyte to explore the role of cathodic pulse in AC or bipolar plasma electrolytic oxidation (PEO) process. SEM observation was carried out to observe the sites of anodic and cathodic breakdown and their morphologies. The prior anodic breakdown accelerated the cathodic breakdown at ?50 V, and the acceleration was associated with the preferential cathodic breakdown at the anodic breakdown sites. However, the succeeding anodic breakdown during applying anodic pulse of 420 V for 2 ms was highly suppressed at the cathodic breakdown sites. This would randomise the anodic breakdown sites. Such role may contribute to the formation of rather uniform coatings on aluminium in this electrolyte without large discharge channels when larger cathodic current is applied with respect to the anodic current in AC PEO.     

Critical assessment 29: TRIP-aided bainitic ferrite steels

Transformation-induced plasticity (TRIP)-aided bainitic ferrite steels developed for automotive applications have attractive mechanical properties such as ductility, formability, toughness, fatigue strength and delayed fracture strength. These mechanical properties are principally associated with a ductile lath-structure matrix and the strain-induced transformation of the metastable-retained austenite films of 3–20 vol.%. In this paper, data on the microstructural and mechanical properties of the low-carbon TRIP-aided bainitic ferrite steels are critically assessed, as well as their deformation mechanism.     

Polyethylene–Carbon Nanotube Composite Film Deposited by Cold Spray Technique

Carbon nanotubes (CNTs) are high-performance materials because of their superior electrical conductivity, thermal conductivity, and self-lubrication, and they have been studied for application to polymer composite materials as fillers. However, the methods of fabricating polymer composites with CNTs, such as injection molding, are too complicated for industrial applications. We propose a simple cold spray (CS) technique to obtain a polymer composite of polyethylene (PE) and CNTs. The composite films were deposited by CS on polypropylene and nano-porous structured aluminum substrates. The maximum thickness of the composite film was approximately 1 mm. Peaks at G and D bands were observed in the Raman spectra of the films. Scanning electron microscopy images of the film surface revealed that PE particles were melted by the acceleration gas and CNTs were attached with melted PE. The PE particles solidified after contact with the substrate. These results indicate that PE–CNT composite films were successfully deposited on polypropylene and nano-porous structured aluminum substrates by CS.     

Influence of Cu metal on the domain structure and carrier mobility in single-layer graphene

We demonstrate that domain structure of single-layer graphene grown by ambient pressure chemical vapor deposition is strongly dependent on the crystallinity of the Cu catalyst. Low energy electron microscopy analysis reveals that graphene grown using a Cu foil gives small and mis-oriented graphene domains with a number of domain boundaries. On the other hand, no apparent domain boundaries are observed in graphene grown over a heteroepitaxial Cu(111) film deposited on sapphire due to unified orientation of graphene hexagons. The difference in the domain structures is correlated with the difference in the crystal plane and grain structure of the Cu metal. The graphene film grown on the heteroepitaxial Cu film exhibits much higher carrier mobility than that grown on the Cu foil.     

Chemical vapor deposition of boron- and nitrogen-containing graphene thin films

Boron and nitrogen-incorporated graphene thin films were grown on polycrystalline Ni substrates by thermal chemical vapor deposition using separate boron- and nitrogen-containing feedstocks. Boron and nitrogen atoms were incorporated in the film in almost equal amounts and the total content reached ∼28%. The film predominantly consisted of separate graphene and boron nitride domains. Carrier concentration in the graphene domains was estimated to be about 1 × 10⁻³ e/atom (3.8 × 10¹² cm⁻²) from G band shift in Raman spectra.     

Effect of α-substituents on molecular motion and wetting behaviors of poly(fluoroalkyl acrylate) thin films with short fluoroalkyl side chains

The effect of α-substituent on the molecular motion and wetting behavior of poly{2-(perfluorobutyl)ethyl acrylate} [PFA-C₄], poly{2-(perfluorobutyl)ethyl methacrylate} [PFMA-C₄], poly{2-(perfluorobutyl)ethyl α-fluoroacrylate} [PFFA-C₄], and poly{2-(perfluorobutyl)ethyl α-chloroacrylate} [PFClA-C₄] films were characterized by dynamic contact angle measurement, lateral force microscopy (LFM), wide angle X-ray diffraction (WAXD), and X-ray photoelectron spectroscopy (XPS). WAXD of oriented PFClA-C₄ fiber suggested the presence of rod-like chain due to the presence of bulky α-substituent. The glass transition temperature (T_g) of PFFA-C₄ and PFClA-C₄ were well above the room temperature. The water repellencies of PFFA-C₄ and PFClA-C₄ were as high as that of PFMA-C₄ and their oil repellency of PFFA-C₄ and PFClA-C₄ was higher than the PFMA-C_4. This result was originated from the low main chain mobility of PFFA-C₄ and PFClA-C₄ due to the presence of bulky α-substituents. The effect of molecular motion on water repellency was clarified by the results of temperature dependence studies of dynamic contact angle, LFM, and surface chemical composition measured by XPS.