Multi-fluid multi-phase subchannel analysis of subassembly accidents of LMFRs

Analyses of experiments simulating hypothetical subassembly accidents such as a large-scale inlet blockage in a Liquid Metal Cooled Fast Reactor (LMFR) have been performed with computer program KAMUI. With the use of relatively simple but reasonable constitutive models, the code has been applied to the SCARABEE experiments BE+1 and APL1 to validate the analytical capability against the accident conditions under the multi-pin geometry. The results show that the key events such as sodium boiling, clad melting, molten clad relocation, molten clad freezing were adequately simulated taking into account the effect of heat loss to the coolant flow in the outside channel of the test section.     

Polyacene capacitors

We fabricated two types of polyacene capacitor with extremely stable polyacenic semiconductor (PAS) as the positive and negative electrodes. The first one is a coin-type PAS capacitor (six different sizes), which possesses large capacity with high reliability. Its capacity is much larger than that of the conventional electric double-layer capacitor which uses activated carbon as electrode. PAS capacitor can maintain more than 70% of the initial capacity even after 100 000 cycles. Moreover, this capacitor can be charged and discharged in a few minutes as well as at low rate. The second one is a cylinder-type PAS capacitor (diameter: 18 mm, height: 65 mm) which shows high capacity of 100 F and can discharge at the extremely high rate of 80 C. The coin-type PAS capacitor is currently used for memory back-up of electrical and communication equipment, and the cylinder-type is considered to be useful as power back-up for starting drive parts of electric equipment which needs high power density.     

Development of AAS resin by the emulsion–suspension polymerization method

In order to improve the weatherability of acryonitrile—styrene—butadiene rubber graft polymer (ABS resin), an attempt was made to develop a resin (AAS resin) in which acrylic rubber of good weatherability was used instead of butadiene rubber. First, by copolymerizing dicyclopentenyl-methacrylate (DCP-MA,3%) with butyl acrylate, crosslinked acrylic rubber was obtained. This also introduced grafting sites into the rubber. Next, methods of graft copolymerizing styrene and acrylonitrile with this rubber were examined. An emulsion–suspension polymerization method was developed in which the initial stage of the polymerization, emulsion polymerization, changed into suspension polymerization during the process. By this method of polymerization, rubber particles were combined and enlarged, bringing about a graft-type resin with high impact resistance. This polymerization method is industrially useful because particle-shaped resins are obtained without the need of a salting-out process. The AAS resin, obtained in this way, has much improved weatherability over ABS resin and shows strength equal to that of ABS resin. © 1992 John Wiley & Sons, Inc.     

Polarization Switching in (100)/(001) Oriented Epitaxial Pb(Zr, Ti)O3 Thin Films

Thin films made of (100)/(001)-oriented Pb(Zr, Ti)O₃ (PZT) were deposited by liquid-delivery metal-organic chemical vapor deposition on Ir/MgAl₂O₄/SiO₂/Si(100) substrates. For comparison, PZT thin films were also deposited on Ir/MgO(100) substrates. The X-ray scan spectra for the (202) reflections revealed that the PZT films have four-fold symmetry. It indicates that the PZT films were epitaxially grown as a cube-on-cube structure on both substrates. The switchable polarization (Q_sw) of the PZT capacitors on the silicon substrate was only 23 C/cm² at 1.8 V; however, Q_sw of PZT capacitors on MgO was 99 C/cm². In the case of PZT films deposited on silicon, the volume fraction of (001)-oriented domains (which contribute to polarization switching) was 15.1% (calculated from an XRD pattern). This result is due to the lower Q_sw of PZT capacitors on silicon. By piezoresponse-force microscopy, switchable and unswitchable domains could be identified by imaging color contrast, namely, (001) and (100) domains, respectively. Consequently, domain distribution of the PZT film on a silicon substrate indicates that the (001) domain exists in the (100) domain matrix.     

Ion beam studies of events typical of soft errors in semiconductor memories

A fast ion microbeam has been used to study phenomena associated with soft errors in semiconductor memories. A spatially small beam with a fast blanking system is used to study both alpha particle and heavy ion strikes. The heavy ion strikes are typical of the recoil from cosmic-ray-generated neutrons. Charge collection and static RAM error-rate experiments are discussed.     

液氦自动补加实验

一种简易的液氦自动补加装置业已制成并通过了试验。该装置由一个１００Ｌ液氦贮存容器、一个蒸发率约５Ｌ／ｄ的低温恒温器、一条１ｍ长的柔性输送管、两个电磁阀、一个５Ｗ电加热器、一个容器压力传感器和控制器以及两个液面传感器和控制器组成。它没有旁通管和输送冷却的阀门。由于用加热器通过液氦蒸发使容器的压力升高，所以安全装置具有防止超压和无液加热的作用。这一简易可靠的装置，它的工作性能已通过模型试验和正常使用所     

Plasma dehydroepiandrosterone sulfate in unipolar major depression. Short communication

We investigated plasma dehydroepiandrosterone sulfate (DHEAS) and cortisol levels in 12 patients with unipolar depression and 11 matched normal controls. The depressed patients showed significantly higher values of plasma DHEAS and cortisol than the controls. After 4 weeks of treatment with antidepressants (mainly clomiplamine), the high plasma DHEAS levels recovered. This finding showed the possible relationship between plasma DHEAS levels and depression, as well as cortisol levels.     

Statistical evaluation of pin gaps in fuel clusters for fugen

The computer program STGAP has been developed to estimate pin gaps in a fuel assembly for FUGEN. The program optionally computes the probable distribution of the pin gap between any adjacent pair of fuel pins, either at a desired location in an assembly or longitudinally averaged over the total effective length of a pin, based on the measured manufacturing and assembling tolerances in geometrical dimensions and mechanical properties of all the independent elements composing a fuel assembly. It also correlates the computed fuel gap distribution with the minimum critical heat flux ratio in the corresponding local subchannel. Sample calculations were performed for the probable distributions of the pin gaps between pairs of adjacent fuel pins in the outermost layer of a FUGEN fuel assembly using the program and satisfactory agreement was obtained with the corresponding measured distributions.     

Probabilistic distributions of pin gaps within a wire-spaced fuel subassembly and sensitivities of the related uncertainties to pin gap

Probabilistic fuel pin gap distributions within a wire-spaced fuel subassembly and sensitivities of the related uncertainties to fuel pin gaps are discussed. The analyses consist mainly of expressing a local fuel pin gap in terms of sensitivity functions of the related uncertainties and calculating the corresponding probabilistic distribution through taking all the possible combinations of the distribution of uncertainties. The results of illustrative calculations show that with the reliability level of 0.9987, the maximum deviation of the pin gap at the cladding hot spot of a center fuel subassembly is 8.05% from its nominal value and the corresponding probabilistic pin gap distribution is shifted to the narrower side due to the external confinement of a pin bundle with a wrapper tube.