Electronic properties of magnetically doped nanotubes

Effect of doping of carbon nanotubes by magnetic transition metal atoms has been considered in this paper. In the case of semiconducting tubes, it was found that the system has zero magnetization, whereas in metallic tubes the valence electrons of the tube screen the magnetization of the dopants: the coupling to the tube is usually antiferromagnetic (except for Cr).     

Low-temperature poly-SiGe alloy growth of high gain/speed pin infrared photosensor with gold-induced lateral crystallization (Au-ILC)

The hydrogenated poly-silicon germanium (poly-SiGe:H) epitaxial film has been investigated using gold-induced lateral crystallization (Au-ILC) technology on a-SiGe:H layers at 10-h 350/spl deg/C annealing temperature and 60-sccm hydrogen (H/sub 2/) content. Using this optimal condition, the growth rate of the induced Au was as large as 15.9 /spl mu/m/h. With a low annealing temperature (/spl les/400/spl deg/C) and large growth rate, this novel technology will be noticeably useful for poly-SiGe:H pin IR-sensing fabrication on a conventional precoated indium tin oxide (ITO)-glass substrate. Under a 1-/spl mu/W IR-LED incident light (with peak wave length at 710 nm) and at a 5-V biased voltage, the poly-SiGe:H pin IR sensor developed by the Au-ILC technology, i.e., an Al (anode)/n poly-SiGe:H/i poly-SiGe:H/p poly-SiGe:H/ITO (cathode)/glass-substrate structure allowed for maximum optical gain and response speed. The optical gains and the response speeds were almost 600 and 130%, respectively, better than that of a traditional pin type. Meanwhile, the FWHM of a poly-SiGe:H pin sensor with Au-ILC technology was reduced from 280 to 150 nm. This reveals excellent IR-sensing selectivity. These IR-sensing trials demonstrated again that the proposed Au-ILC technology has very useful application in the field of low cost integrated circuits on optoelectronic applications.     

Understanding the differences between how novice and experienced designers approach design tasks

Research was undertaken to understand how to provide the most appropriate support for novice designers in engineering design. However, how designers apply their experience and knowledge is not understood and further research in this area is required. This paper describes an observational study to understand how novice and experienced designers approach design tasks. Electronic Publication     

Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

A New Approach for Built‐in Self‐Test of 4.5 to 5.5 GHz Low‐Noise Amplifiers

This paper presents a low‐cost RF parameter estimation technique using a new RF built‐in self‐test (BIST) circuit and efficient DC measurement for 4.5 to 5.5 GHz low noise amplifiers (LNAs). The BIST circuit measures gain, noise figure, input impedance, and input return loss for an LNA. The BIST circuit is designed using 0.18 μm SiGe technology. The test technique utilizes input impedance matching and output DC voltage measurements. The technique is simple and inexpensive.     

General expression for pdf of a sum of independent exponential random variables

In order to evaluate exactly the performance of some diversity schemes, the probability density function (pdf) of a sum of independent exponential random variables (r.v.'s) must be known. This paper proposes a simple method to find it by using characteristic function., The resultant pdf is successfully applied to formulate the closed-form BER expression of 2 Tx-J Rx transmit diversity as well as the outage probability of repetition coding.     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Diagnostic value of the study of caffeine elimination in chronic liver diseases

Data from the past few years have shown that as caffeine metabolizes solely in the liver, caffeine elimination can serve as a liver function test. We have collected data by monitoring 40 persons with liver diseases (11 chronic alcoholic hepatitis, 24 liver cirrhosis, 5 non-cirrhotic liver disease). Eight subjects served as controls. The patients with liver cirrhosis were classified according to the Child--Pugh scoring system. To determine caffeine elimination blood samples were collected before and at 3, 6, 9 and 12 hours after oral administration of 0.2 g caffeine. Fasting serum caffeine concentration and concentration 12 hours after administration, serum clearance, half life, peak concentration and volume of distribution have been compared. The respective values measured in patients with non-cirrhotic liver diseases did not differ significantly from the controls. The disappearance of caffeine was significantly decreased in cirrhotics. Our results demonstrated a good correlation between impairment of caffeine elimination and assessment of severity of liver disease by the Child--Pugh classification. Measuring serum levels in samples taken 12 hours after caffeine administration is a simple and useful method in the diagnosis of liver diseases at cirrhotic stage.