中原高温高盐油藏疏水缔合聚合物凝胶调剖剂研究

针对中原油田高温(>80℃)、高盐度(>50 g/L)、高硬度(>1 g/L)砂岩油藏,研制了地下成胶的高热稳定性聚合物凝胶调剖剂。所用聚合物为疏水缔合聚合物AP-P4,M=9.0×106,HD=27%,疏水基摩尔分数0.2%;交联剂为可生成酚醛树脂的3种化合物;调剖剂胶液用矿化度160 g/L的马寨油田污水配制;实验温度95℃。根据形成的凝胶黏度(95℃,1.1 s-1)确定交联剂各组分用量为:MZ-YL 0.429%,MZ-BE 0.060%,MZ-XS 0.012%;酸度调整剂用量0.12%;成胶时间10~15小时。2.5、3.0、3.5 g/L AP-P4的凝胶在95℃老化100天后黏度保持在~40 Pa.s及以上。初配制胶液在3000 r/min下剪切15分钟后黏度降低87.5%~89.0%,但成胶后和老化过程中凝胶黏度只比未剪切样降低17.1%~6.6%。3.5 g/L AP-P4的调剖剂对~1μm2的6支储层岩心的堵塞率在88.1%~95.8%范围,平均93.3%,造成的残余阻力系数在15.2~28.6范围,平均19.8,使渗透率级差2.3~8.0的4组双人造岩心的注水流量比发生不同程度的反转。认为该凝胶调剖剂高温下稳定性好的原因,是强化学交联密度低,因而凝胶脱水收缩作用弱。图2表5参5。     

Novel Folded Waveguide Resonator Filter Using Slot Technique

This letter presents a primary investigation into developing a compact and low-loss bandpass filter using novel folded-waveguide resonators with a footprint reduction. A slot coupling between adjacent resonators is introduced, which is characterized using full-wave electromagnetic simulations and verified experimentally. Two two-pole folded-waveguide resonator filters of this type have been designed, fabricated and tested. Simulation and measurement results are presented to validate the design and to show the advantages of this type of filter.     

光谱法快速测定土壤中的多个微量元素

本法采用碳酸钡、氟化锂、石墨粉作缓冲剂，用锑做铅锌的标．用铪作铌的内标，用钯作铍、铬、镧、锶、铜的内标。采用小孔电极，交流电弧做为激发光源，同时测定铅、锡、锌、铍、铬、镧、铌、铜、锶等九个元素。分析数据基本稳定．能达到土壤样品的检出限要求。     

Lactic acid production from dining‐hall food waste by Lactobacillus plantarum using response surface methodology

BACKGROUND: Food waste generally has a high starch content and is rich in nutritional compounds, including lipids and proteins. It therefore represents a potential renewable resource. In this study, dining‐hall food waste was used as a substrate for lactic acid production, and response surface methodology was employed to optimise the fermentation conditions. RESULTS: Lactic acid biosynthesis was significantly affected by the interaction of protease and temperature. Protease, temperature and CaCO₃ had significant linear effects on lactic acid production, while α‐amylase and yeast extract had insignificant effects. The optimal conditions were found to be an α‐amylase activity of 13.86 U g^?1 dried food waste, a protease activity of 2.12 U g^?1 dried food waste, a temperature of 29.31 °C and a CaCO₃ concentration of 62.67 g L^?1, which resulted in a maximum lactic acid concentration of 98.51 g L^?1 (88.75% yield). An increase in inoculum size would be appropriate for accelerating the depletion of initial soluble carbohydrate to enhance the efficiency of α‐amylase in dining‐hall food waste fermentation. CONCLUSION: A suitable regression model for lactic acid production was developed based on the experimental results. Dining‐hall food waste was found to be a good substrate for lactic acid fermentation with high product yield and without nutrient supplementation. Copyright © 2008 Society of Chemical Industry     

Restraining the associations of anthracene fluorophore by chemically linking to poly(methyl methacrylate)

Associations (dimer or aggregate) of anthracene (An) fluorophores tend to interrupt the monomer emission and reduce the quantum yield (Φ_PL); therefore, poly(methyl methacrylate) (PMMA) chain was used in this study to chemically link to anthracene and to block the mutual associations among the anthracene fluorophores. With this aim, the target polymers were prepared by anionic polymerizations with 9,10‐dibromoanthracene/s‐butyllithium as initiating system to proceed polymerizations of methyl methacrylate (MMA) directly or in the presence of 1,1‐diphenylethylene (DPE). Use of DPE before addition of MMA produces stable initiating anionic species and avoids potential side reactions during polymerization; however, it also introduces four β‐phenylene rings around the central anthracene ring, which interfere with the corresponding emission pattern and reduce the Φ_PL (32%) value due to potential interactions between phenylene rings and anthracene. On the contrast, polymerization without participation of DPE results in polymer with central anthracene ring directly connected to two PMMA chains, which gives clean vibronic emission pattern with limited association emissions and enhanced Φ_PL (52%) value. Physical blending of anthracene by PMMA is less efficient to restrain the associations and results in a film of lower Φ_PL (20%). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and properties of novel amphiphilic sulfated ionomers by the ring‐opening reaction of an epoxidized styrene–butadiene–styrene triblock copolymer

A method for the synthesis of novel sulfated ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed. SBS was first epoxidized by performic acid in the presence of a phase‐transfer catalyst; this was followed by a ring‐opening reaction with an aqueous solution of alkali salt of bisulfate. The optimum conditions for the ring‐opening reaction of the epoxidized SBS with an aqueous solution of KHSO₄ were studied. During the ring‐opening reaction, both phase‐transfer catalyst and ring‐opening catalyst were necessary to enhance the conversion of epoxy groups to ionic groups. The products were characterized with Fourier transform infrared spectrophotometry and transmission electron microscopy (TEM). After the potassium ions of the ionomer were substituted with lead ions, the lead sulfated ionomer exhibited dark spots under TEM. Some properties of the sulfated ionomer were studied. With increasing ionic groups or ionic potential of the cations, the water absorbency and emulsifying volume of the ionomer and the intrinsic viscosity of the ionomer solution increased, whereas the oil absorbency decreased. The sulfated ionomer possessed excellent emulsifying properties compared with the sulfonated SBS ionomer. The sodium sulfated ionomers in the presence of 10% zinc stearate showed better mechanical properties than the original SBS. When the ionomer was blended with crystalline polypropylene, a synergistic effect occurred with respect to the tensile strength. The ionomer behaved as a compatibilizer for blending equal amounts of SBS and oil‐resistant chlorohydrin rubber. In the presence of 3% ionomer, the blend exhibited much better mechanical properties and solvent resistance than the blend without the ionomer. SEM photographs indicated improved compatibility between the two components of the blend in the presence of the ionomer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

面向技术创新机遇组建虚拟企业与兼并行为的比较分析

以技术创新机遇为例分析了核心企业选择实现市场机遇的战略模式的决策过程，并给出核心企业选择实现市场机遇的战略模式的决策模型。在模型中考虑了核心企业组建虚拟企业的一个重要目的就是快速地实现市场机遇，因此在提出的决策模型中引入了时间因素。研究结果表明，当市场机遇生命周期较长时，核心企业采取兼并策略优于组建虚拟企业，反之组建虚拟企业更有利。最后提出采用期权定价模型来判断组建虚拟企业的价值，并举例说明。     

武钢第二炼钢厂连铸坯喷号机自动控制系统

对武钢第二炼钢厂连铸坯喷号机自动化控制景统配置、网络通讯、伺服控制系统进行了阐述；经运行考验证明系统性能提高、稳定可靠。     

住宅楼温度裂缝产生的原因与防治措施

本文对建筑物温度裂缝产生的原因进行了分析和探讨 ,并从设计、施工方面对防治裂缝提出了措施。