A micromachined electrochemical sensor for free chlorine monitoring in drinking water.

In this work, we designed, fabricated and tested a disposable, flow-through amperometric sensor for free chlorine determination in water. The sensor is based on the principle of an electrochemical cell. The substrate, as well as the top microfluidic layer, is made up of a polymer material. The advantages include; (a) disposability from low cost; (b) stable operation range from three-electrode design; (c) fluidic interconnections that provide on line testing capabilities; and (d) transparent substrate which provides for future integration of on-chip optics. The sensor showed a good response and linearity in the chlorine concentration ranging from 0.3 to 1.6 ppm, which applies to common chlorination process for drinking water purification.     

双能X射线骨密度仪测定技术研究

以Ｌｕｎａｒ公司ＤＰＸ－Ｌ型双能Ｘ射线骨密度仪为例，研究引起测量误差的主要因素并提出质控措施。用自检模块、腰椎体膜评定仪器的体外测量精度好于１％。对１０位志愿者重复２次测量，体内精度对腰椎，ＭＰＤ（平均百分差）为０．４６，ＣＶ（变异系数）为０．７５；对股骨颈，ＭＰＤ为１．２６、ＣＶ为０．４７；Ｗａｒｄ’ｓ三角区ＭＰＤ为２．０１、ＣＶ为１．１４；大转子ＭＰＤ为１．６６、ＣＶ为０．７２。扫描图像由２位     

Nonregular feedback linearization: a nonsmooth approach

In this note, we address the problem of exact linearization via nonsmooth nonregular feedback. A criterion of nonregular static state feedback linearizability is presented for a class of nonlinear affine systems with two control inputs, and its application to nonholonomic systems is briefly discussed.     

EC与~（99m）Tc－GH之间的配体交换反应动力学研究

实验表明，ＥＣ浓度与配体交换反应速度常数无关，体系的ｐＨ值对速度常数和９９ｍＴｃ－ＥＣ的标记率影响较大。测定并计算了不同ｐＨ值的交换反应速度常数。结果表明，为保证用配体交换法制备９９ｍｃ－ＥＣ时９９ｍｃ－ＥＣ的标记率大于９０％，体系的ｐＨ值必须≥８。     

用CAXA电子图板求解冲模压力中心

在模具设计中 ,冲裁模压力中心通常采用解析法或图解法求解。本文提出一种用CAXA绘图软件在设计制图时直接求解的方法 ,快速直接 ,简单方便 ,精度较高。     

Influence of volatile matter and deposited carbon on coke yield from coals

The relations between coke yields and the volatile matter content of 30 individual and 30 blended coals were investigated. Coke yields and deposited carbon related to volatile matter content can be expressed in the following equations: CY (%) = 97.89?0.86 VMch+VMc; and DC (%)= ?2.24+0.16 VMch; where: CY=real coke yield; VMch = volatile matter content of charging coal; VMc=volatile matter content of coke, and in the case of <2%; DC = deposited carbon. The test results show excellent correlation with practice.     

如何提高预焙铝电解槽阳极质量

预焙阳极的质量已严重制约铝电解技术的发展，必须予以足够的重视．国外在提高阳极质量方面的有效措施，可以供国内阳极工厂技术改造及科研攻关借鉴．     

Poly(3‐chlorothiophene) films prepared by the direct electrochemical oxidation of 3‐chlorothiophene in mixed electrolytes of boron trifluoride diethyl etherate and sulfuric acid

3‐Chlorothiophene (CT) was electrochemically polymerized in mixed electrolytes of a boron trifluoride diethyl etherate solution containing 0–20% (by volume) sulfuric acid. The oxidation potentials of the monomer in these media were measured to be only 1.06–1.31 V (vs Ag/AgCl). These values were much lower than that of CT in acetonitrile and 0.1 mol/L (Bu)₄NBF₄ (1.92 V vs Ag/AgCl). Poly(3‐chlorothiophene) (PCT) films with conductivities of 0.1–2 S cm^?1 were obtained. The structure, morphology, and electrochemical behavior of the PCT films also were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 502–509, 2003     

Strain-induced crystallization,Part IV: Induction time analysis

The empirical equation, 1/t_i = Ae^Ei/RT, which expresses the exponential dependence of the reciprocal of crystallization induction time, t_i, has been analyzed and shown to be equivalent to the nucleation rate equations derived earlier in Part III (1). Consequently we have used the t_i measurements obtained earlier by Krueger and Yeh to calculate not only the nucleation rate enhancements but also the melting point elevations, the relative crystal thickness changes and molecular coil extension ratios of shear-crystallization polyethylene. It is shown that polyethylene when crystallized between 129 and 131°C at shear rates between 1.56 and 9.70 sec^?1 can have melting point increases of 4.2 to 7.2°C and crystal thickness decreases of 20 to 25 percent, when compared to those crystallized at 130°C in the quiescent state. The predicted “coil” extension in the melt just prior to shear-induced crystallization ranges between 21 and 36 percent. The results of these analyses as well as those on nucleation rates of polyethylene oxide are discussed in detail.