A new hybrid active power filter (APF) topology

In this paper, a new hybrid active power filter topology is presented. A higher-voltage, low-switching frequency insulated gate bipolar transistor (IGBT) inverter and a lower-voltage high-switching frequency metal oxide semiconductor field effect transistor (MOSFET) inverter are used in combination to achieve harmonic current compensation. The function of the IGBT inverter is to support utility fundamental voltage and to compensate for the fundamental reactive power. The MOSFET inverter fulfills the function of harmonic current compensation. To further reduce cost and to simplify control, the IGBT and MOSFET inverters share the same DC-link via a split capacitor bank. With this approach harmonics can be cancelled over a wide frequency range. Compared to the conventional APF topology, the proposed approach employs lower dc-link voltage and generates less noise. Simulation and experimental results show that the proposed active power filter topology is capable of compensating for the load harmonics     

A new measurement technique for obtaining the complex relativepermittivity of terrain surfaces

A new method for measuring the effective complex relative permittivity of a reflecting surface is presented. The approach is based on the two-ray model. We derive an equation of a circle representing the complex reflection coefficient which relates the incidence angle, frequency, and received power from the path gain using the two-ray model. The intersection point of three such circles at different heights, while maintaining the same incidence angle, yields the correct complex reflection coefficient value. By measuring the received power for both the vertical and horizontal polarizations, the relative permittivity of the surface can be determined. The technique is validated using computer simulation, as well as field measurements of typical terrain surfaces, such as asphalt, grass, and bare soil. A major advantage of this method is that it obviates the need to use antennas with a narrow beam pattern     

Long-wavelength GaInNAs(Sb) lasers on GaAs

The boom in fiber-optic communications has caused a high demand for GaAs-based lasers in the 1.3-1.6-μm range. This has led to the introduction of small amounts of nitrogen into InGaAs to reduce the bandgap sufficiently, resulting in a new material that is lattice matched to GaAs. More recently, the addition of Sb has allowed further reduction of the bandgap, leading to the first demonstration of 1.5-μm GaAs-based lasers by the authors. Additional work has focused on the use of GaAs, GaNAs, and now GaNAsSb barriers as cladding for GaInNAsSb quantum wells. We present the results of photoluminescence, as well as in-plane lasers studies, made with these combinations of materials. With GaNAs or GaNAsSb barriers, the blue shift due to post-growth annealing is suppressed, and longer wavelength laser emission is achieved. Long wavelength luminescence out to 1.6 μm from GaInNAsSb quantum wells, with GaNAsSb barriers, was observed. In-plane lasers from these samples yielded lasers operating out to 1.49 μm, a minimum threshold current density of 500 A/cm² per quantum well, a maximum differential quantum efficiency of 75%, and pulsed power up to 350 mW at room temperature     

A Thermoelectric Generator Using Engine Coolant for Light-Duty Internal Combustion Engine-Powered Vehicles

We proposed and fabricated a thermoelectric generator (TEG) using the engine water coolant of passenger vehicles. The experimental results revealed that the maximum output power from the proposed thermoelectric generator was ~75 W, the calculated thermoelectric module efficiency of the TEG was ~2.1%, and the overall efficiency of electric power generation from the waste heat of the engine coolant was ~0.3% in the driving mode at 80 km/h. The conventional radiator can thus be replaced by the proposed TEG without additional devices or redesign of the engine water cooling system of the existing radiator.     

Effect of Vacancy Distribution on the Thermal Conductivity of Ga<Subscript>2</Subscript>Te<Subscript>3</Subscript> and Ga<Subscript>2</Subscript>Se<Subscript>3</Subscript>

Our group has focused attention on Ga₂Te₃ as a natural nanostructured thermoelectric material. Ga₂Te₃ has basically a zincblende structure, but one-third of the Ga sites are structural vacancies due to the valence mismatch between Ga and Te. It has been confirmed that (1) vacancies in Ga₂Te₃ exist as two-dimensional (2D) vacancy planes, and (2) Ga₂Te₃ exhibits an unexpectedly low thermal conductivity (κ), most likely due to highly effective phonon scattering by the 2D vacancy planes. However, the effect of the size and periodicity of the 2D vacancy planes on κ has been unclear. In addition, it has also been unclear whether only the 2D vacancy planes reduce κ or if point-type vacancies can also reduce κ. In the present study, we tried to prepare Ga₂Te₃ and Ga₂Se₃ with various vacancy distributions by controlling annealing conditions. The atomic structures of the samples were characterized by means of transmission electron microscopy, and κ was evaluated from the thermal diffusivity measured by the laser flash method. The effects of vacancy distributions on κ of Ga₂Te₃ and Ga₂Se₃ are discussed.     

Enhanced Performance of I2‐Free Solid‐State Dye‐Sensitized Solar Cells with Conductive Polymer up to 6.8%

An iodine‐free solid‐state dye‐sensitized solar cell (ssDSSC) is reported here, with 6.8% energy conversion efficiency—one of the highest yet reported for N719 dye—as a result of enhanced light harvesting from the increased transmittance of an organized mesoporous TiO₂ interfacial layer and the good hole conductivity of the solid‐state‐polymerized material. The organized mesoporous TiO₂ (OM‐TiO₂) interfacial layer is prepared on large‐area substrates by a sol‐gel process, and is confirmed by scanning electron microscopy (SEM) and grazing incidence small‐angle X‐ray scattering (GISAXS). A 550‐nm‐thick OM‐TiO₂ film coated on fluorine‐doped tin oxide (FTO) glass is highly transparent, resulting in transmittance increases of 8 and 4% compared to those of the bare FTO and conventional compact TiO₂ film on FTO, respectively. The high cell performance is achieved through careful control of the electrode/hole transport material (HTM) and nanocrystalline TiO₂/conductive glass interfaces, which affect the interfacial resistance of the cell. Furthermore, the transparent OM‐TiO₂ film, with its high porosity and good connectivity, exhibits improved cell performance due to increased transmittance in the visible light region, decreased interfacial resistance ( Ω ), and enhanced electron lifetime ( τ ). The cell performance also depends on the conductivity of HTMs, which indicates that both highly conductive HTM and the transparent OM‐TiO₂ film interface are crucial for obtaining high‐energy conversion efficiencies in I₂‐free ssDSSCs.     

Measurement of nonlinear mechanical properties of PDMS elastomer

This paper presents the measurement of the nonlinear mechanical properties of polydimethylsiloxane (PDMS) elastomer based on the mixing ratio of base polymer to curing agent. Strip-type PDMS samples with different mixing ratios were prepared using a simple coating, curing, and cutting process. A cyclic uniaxial tension test with a fixed magnitude of applied strain and a single-pull-to-failure tension test were performed with a micro-tensile tester at room temperature.Our new finding is that when the PDMS is mixed with excessive curing agent, stress softening occurs and residual strain exists in cyclic tension tests when the magnitude of the applied strain increases. For the PDMS-05 samples, in which the mixing ratio of base polymer to curing agent was 5 to 1, there were large differences in the stresses for the same strain level under loading and unloading during the first cycle with a 100% fixed strain amplitude, but the softening effect of the stress in the PDMS dropped rapidly starting from the second cycle.Nonlinear mechanical Neo-Hookean, third-order Mooney, and second-order Ogden models of three different PDMS films were computed from the stress-strain data. The results showed that all models were preferable for the small strain region of PDMS compared with other models. In the nonlinear, large strain region, only the second-order Ogden model properly described the mechanical behavior of the PDMS, while the Neo-Hookean and third-order Mooney-Rivlin models were too stiff or flexible in the measurement range. The bulk modulus of PDMS increased with the amount of curing agent in it. Therefore, the second-order Ogden model is preferable for analyzing the PDMS structure over the entire measurement range. This could provide reasonable mechanical models of PDMS for rapid computational prototyping and for designing active and passive components from PDMS.     

Biometric bits extraction through phase quantization based on?feature level fusion

Biometric bits extraction has emerged as an essential technique for the study of biometric template protection as well as biometric cryptosystems. In this paper, we present a non-invertible but revocable bits extraction technique by means of quantizing the facial data from two feature extractors in the phase domain, which we coin as aligned feature-level fusion phase quantization (AFPQ). In this technique, we utilize helper data to achieve the revocability requirement of bits extraction. The feature averaging and remainder normalization technique are integrated with the helper data to reduce feature variance within the same individual and increase the distinctiveness of bit strings of different individuals to achieve good recognition performance. A scenario in which the system is compromised by an adversary is also considered. As a generic technique, AFPQ can be easily extended to multiple different biometric modalities.     

部分响应连续相位调制信号在卫星移动信道中的误比特率性能分析

该文给出了组合卫星移动信道中采用差分相位检测(DPD)和最大比组合(MRC)的部分响应连续相位调制(PRCPM)信号的误比特率计算公式,并给出了有关数值计算结果。