Electrical and optical feedback in an InGaAs/InP light-amplifyingoptical switch (LAOS)

A circuit model for optical and electrical feedback has been developed to investigate the cause of negative differential resistance (NDR) switching in a series connected heterojunction phototransistor (HPT) light-emitting diode (LED) device. The model considers optical feedback from the light generated in the LED, electrical feedback from the holes thermally emitted over the LED cladding layer, nonlinear gain of the HPT, the Early effect, and leakage resistance. The analysis shows that either electrical or optical feedback can be the dominant cause for the NDR, depending upon their relative strengths. The NDR observed in the devices was caused primarily by electrical feedback since the optical feedback is weak. For low input power, avalanche breakdown appears to initiate the NDR in the devices although avalanching alone cannot cause NDR     

An integrated air-gap-capacitor pressure sensor and digital readoutwith sub-100 attofarad resolution

The fabrication and characterization of an integrated air-gap-capacitor pressure sensor are presented. The capacitor fabrication process uses standard IC processing to create NMOS circuits, and an added polysilicon layer to create poly-to-n⁺ capacitors with a 0.6-μm-thick dielectric using deposited oxide. Subsequent processing is used to produce deformable, parallel-plate, air-gap capacitors on the front side alongside MOS circuits. Sensor chips are fabricated using 100-μm×100-μm, 100-fF air-gap capacitors with on-chip circuitry. The sensor chip is a part of a capacitive measurement system that uses a charge-redistribution sense technique to achieve very high capacitance resolution. The behavior of the pressure sensor chips was studied as a function of applied pressure in the 0-240-kPa (0-35-psi) range. Measurements indicate a sensitivity of 0.93 mV/kPa (6.40 mV/psi) with a deflection of 10 nm/kPa (70 nm/psi) at 0-69 kPa (0-10 psi). Standard deviations indicate a static pressure resolution of 0.54 kPa (0.078 psi), which translates to 30 attofarads at a sampling frequency of 11 kHz     

Application of artificial neural networks to the analysis of two‐dimensional fluorescence spectra in recombinant E coli fermentation processes

A two‐dimensional (2D) spectrofluorometer was used to monitor various fermentation processes with recombinant E coli for the production of 5‐aminolevulinic acid (ALA). The whole fluorescence spectral data obtained during a process were analyzed using artificial neural networks, ie self‐organizing map (SOM) and feedforward backpropagation neural network (BPNN). The SOM‐based classification of the whole spectral data has made it possible to qualitatively associate some process parameters with the normalized weights and variances, and to select some useful combinations of excitation and emission wavelengths. Based on the classified fluorescence spectra a supervised BPNN algorithm was used to predict some of the process parameters. It was also shown that the BPNN models could elucidate some sections of the process's performance, eg forecasting the process's performance. Copyright © 2005 Society of Chemical Industry     

Survey of nitrate and nitrite contents of vegetables grown in Korea.

A scientific basis for the evaluation of the risk to public health arising from excessive dietary intake of nitrate in Korea is provided. The nitrate () and nitrite () contents of various vegetables (Chinese cabbage, radish, lettuce, spinach, soybean sprouts, onion, pumpkin, green onion, cucumber, potato, carrot, garlic, green pepper, cabbage and Allium tuberosum Roth known as Crown daisy) are reported. Six hundred samples of 15 vegetables cultivated during different seasons were analysed for nitrate and nitrite by ion chromatography and ultraviolet spectrophotometry, respectively. No significant variance in nitrate levels was found for most vegetables cultivated during the summer and winter harvests. The mean nitrates level was higher in A. tuberosum Roth (5150 mg kg(-1)) and spinach (4259 mg kg(-1)), intermediate in radish (1878 mg kg(-1)) and Chinese cabbage (1740 mg kg(-1)), and lower in onion (23 mg kg(-1)), soybean sprouts (56 mg kg(-1)) and green pepper (76 mg kg(-1)) compared with those in other vegetables. The average nitrite contents in various vegetables were about 0.6 mg kg(-1), and the values were not significantly different among most vegetables. It was observed that nitrate contents in vegetables varied depending on the type of vegetables and were similar to those in vegetables grown in other countries. From the results of our studies and other information from foreign sources, it can be concluded that it is not necessary to establish limits of nitrates contents of vegetables cultivated in Korea due to the co-presence of beneficial elements such as ascorbic acid and alpha-tocopherol which are known to inhibit the formation of nitrosamine.     

An online technique for monitoring the insulation condition of AC machine stator windings

A novel online technique for monitoring the insulation condition of ac machine stator windings is proposed in this paper. The concept is to measure the differential leakage currents of each phase winding from the terminal box in a noninvasive manner to assess the insulation condition during motor operation. The conventional differential CTs used for phase fault protection can be replaced with high performance current sensors to measure the leakage current with higher accuracy. Indicators for insulation condition such as the capacitance and dissipation factor are calculated based on the measurements to provide a low cost solution for online insulation condition assessment. A simplified online insulation system model is derived for analysis and interpretation of the measured data. Experimental results on a 15-hp induction motor under simulated insulation degradation conditions show that the proposed technique is a very sensitive method capable of detecting incipient signs of insulation degradation.     

Manufacturing and structural safety evaluation of a composite train carbody

This paper explains the manufacturing process of a composite train carbody with a sandwich composite structure for bodyshell and a stainless steel structure for the under frame. In addition, the structural behavior and safety of the composite carbody of the Korean tilting train was investigated by the static load tests. From the test results, the stiffness of the composite carbody met the specified design. In the aspect of strength, the maximum stress of the composite bodyshell was of 12.2% of strength of CF1263 carbon/epoxy.