Characterization and comparison of PECVD silicon nitride and silicon oxynitride dielectric for MIM capacitors

In this letter, we report on the electrical characteristic and the comparison of the metal-insulator-metal (MIM) capacitors with PECVD silicon nitride (SiN) and silicon oxynitride (SiON). Both capacitors are found to exhibit low leakage and high breakdown field strength, as well as absence of dispersive behavior, good linearity, and comparable quality factor behaviors.     

Field dependence of impact ionization coefficients in In/sub 0.53/Ga/sub 0.47/As

Electron and hole ionization coefficients in In/sub 0.53/Ga/sub 0.47/As are deduced from mixed carrier avalanche photomultiplication measurements on a series of p-i-n diode layers, eliminating other effects that can lead to an increase in photocurrent with reverse bias. Low field ionization is observed for electrons but not for holes, resulting in a larger ratio of ionization coefficients, even at moderately high electric fields than previously reported. The measured ionization coefficients are marginally lower than those of GaAs for fields above 250 kVcm/sup -1/, supporting reports of slightly higher avalanche breakdown voltages in In/sub 0.53/Ga/sub 0.47/As than in GaAs p-i-n diodes.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

The Effect of Moisture Content on the Conversion of Ergosterol to Vitamin D in Shiitake Mushrooms

The distribution of ergosterol in different parts of shiitake mushrooms was studied in order to optimize the conversion of ergosterol to vitamin D₂ during drying. The effect of moisture on the conversion of ergosterol to vitamin D₂ was also investigated by adjusting the moisture content of fresh mushrooms to different levels in a large vacuum desiccator and subjecting them to UV irradiation at 290-320 nm wavelength, for 2 h. The moisture, ergosterol and vitamin D₂ contents were determined using standard procedures. It was found that the ergosterol content on a dry matter basis of fresh shiitake mushroom was highest in the gills (10.6 ± 0.99 mg/g DM), followed by the cap or pileus (5.34 ± 0.64 mg/g DM) and was least in the stalk or stipe (2.97 ± 0.56). The moisture content had a marked influence on the conversion of ergosterol to vitamin D₂, the best conversion taking place at a moisture content of about 70% on a wet basis.     

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO2 for no reduction by NH3

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO₂ for NO reduction by NH₃ was examined in a fixed-bed flow reactor. The deactivation of the catalyst was strongly dependent on reaction temperature. At high reaction temperatures over 300°C, the catalyst did not lose its initial activity up to 50 h of operation, regardless of SO₂ feed concentration from 500 to 20,000 ppm. However, at low reaction temperatures near 250°C, apparent deactivation did occur. Changes in the physicochemical properties such as surface area and sulfur content of deactivated catalyst well correlated with catalyst activity, depending upon reaction temperatures. The deactivation was due to pore blocking and/or filling by deactivating agents, which plugged and/or filled the pores of catalyst. The deactivating agents deposited on the catalyst surface were presumed to be (NH₄)₂SO₄ and/or (NH₄)HSO₄ from the results of TGA and ion-chromatography measurement.     

Monolithic SiGe Up‐/Down‐Conversion Mixers with Active Baluns

The purpose of this paper is to describe the implementation of monolithically matching circuits, interface circuits, and RF core circuits to the same substrate. We designed and fabricated on‐chip 1 to 6 GHz up‐conversion and 1 to 8 GHz down‐conversion mixers using a 0.8 µm SiGe hetero‐junction bipolar transistor (HBT) process technology. To fabricate a SiGe HBT, we used a reduced pressure chemical vapor deposition (RPCVD) system to grow a base epitaxial layer, and we adopted local oxidation of silicon (LOCOS) isolation to separate the device terminals. An up‐conversion mixer was implemented on‐chip using an intermediate frequency (IF) matching circuit, local oscillator (LO)/radio frequency (RF) wideband matching circuits, LO/IF input balun circuits, and an RF output balun circuit. The measured results of the fabricated up‐conversion mixer show a positive power conversion gain from 1 to 6 GHz and a bandwidth of about 4.5 GHz. Also, the down‐conversion mixer was implemented on‐chip using LO/RF wideband matching circuits, LO/RF input balun circuits, and an IF output balun circuit. The measured results of the fabricated down‐conversion mixer show a positive power conversion gain from 1 to 8 GHz and a bandwidth of about 4.5 GHz.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

Efficient Computation of EXIT Functions for Nonbinary Iterative Decoding

The calculation of nonbinary extrinsic information transfer charts for the iterative decoding of concatenated index-based codes is addressed. We show that the extrinsic information at the output of a constituent a posteriori probability decoder can be calculated with very low complexity, where expensive histogram measurements are not required any more. An example for turbo trellis-coded modulation demonstrates the capabilities of the proposed approach     

The slot-coupled hemispherical dielectric resonator antenna with a parasitic patch: applications to the circularly polarized antenna and wide-band antenna

The aperture-coupled hemispherical dielectric resonator antenna (DRA) with a parasitic patch is studied rigorously. Using the Green's function approach, integral equations for the unknown patch and slot currents are formulated and solved using the method of moments. The theory is utilized to design a circularly polarized (CP) DRA and a wide-band linearly polarized (LP) DRA. In the former, the CP frequency and axial ratio (AR) can easily be controlled by the patch location and patch size, respectively, with the impedance matched by varying the slot length and microstrip stub length. It is important that the AR will not be affected when the input impedance is tuned, and the CP design is therefore greatly facilitated. For the wide-band LP antenna, a maximum bandwidth of 22% can be obtained, which is much wider than the previous bandwidth of 7.5% with no parasitic patches. Finally, the frequency-tuning characteristics of the proposed antenna are discussed. Since the parasitic patch can be applied to any DRAs, the method will find applications in practical DRA designs.     

A kinetic study on isothermal crystallization of palm oil by solid fat content measurements

Isothermal crystallization of plam oil was studied by means of differential scanning calorimetry (DSC) as well as by nuclear magnetic resonance spectrometry to monitor its solid fat content (SFC). The temperature of crystallization (Tc) varied from 0 to 30°C, depending on the method used. The plot of %SFC vs. time at 25°C was sigmoidal in shape. However, at lower temperatures, two consecutive curves were clearly visible. Results from DSC experiments showed the following interesting features. At each Tc, the crystals produced were of different compositions. From 0 to 8°C, the thermogram showed three peaks, with the first two peaks (I and II) sharp, and the third (III) rather broad. At elevated temperatures up to 20°C, peak II disappeared totally while peak III tended to shift toward peak I. Above 20°C, both peaks shifted downward to longer times. Peak I continued to be broadened, and then suddenly disappeared at Tc above 24°C. The melting thermograms of the crystals obtained above and below this cut-off point were distinctly different. Kinetic studies on isothermal crystallization based on the data of SFC measurements showed that the data fit well into the Avrami-Erofeev equation with n=3 over the first 70% of the crystallization.