低银医用X光胶片的研制

对几种增黑剂进行了筛选实验研究，选用了两种增黑剂组合使用，提高了遮盖力，使医用Ｘ光胶片涂布银量由原业的９ｇ／ｍ２降到了６．８ｇ／ｍ２，与美国医用Ｘ光胶片涂布银量（６．７ｇ／ｍ２）相当，照相性能不低于国产医用Ｘ光胶片。     

Fabrication and Characterization of Carbon Nanotube–Titanium Nitride Composites with Enhanced Electrical and Electrochemical Properties

This work reports the fabrication and the characterization of a new composite consisting of multiwalled carbon nanotubes (CNTs) and conducting titanium nitride (TiN) with a higher specific surface area ( S _BET), enhanced electrical conductivity (σ), and specific capacitance. With increasing CNT content, the electrical conductivity and electrochemical performance of the CNT–TiN composites gradually increase. In the presence of 5 wt% (12.0 vol%) CNTs, the electrical conductivity and the weight-specific capacitance of CNT–TiN composite are increased by 3.6 times and 54.8% compared with pure TiN, respectively.     

汽车空调冷凝器腐蚀试验的表征与评价

介绍了汽车空调冷凝器的腐蚀试验程度及方法，对试验后的冷凝器进行了密封性检查，并用光学显微镜和扫描电镜检测和分析了材料的显微结构，焊接质量，腐蚀性质及其腐蚀深度等。通过对冷凝器的宏微观检查与表征，评价了冷凝器质量的优劣，提出了改进措施与建议。     

热轧高强钢平整机辊径参数设计技术研究

基于高强钢平整机的生产工艺特点,结合板形与辊耗问题,将带材的出口前张力与辊间压力横向分布都均匀作为目标函数,把保证所有被平整高强钢产品的机械性能满足产品大纲要求作为约束条件,提出了一套针对热轧高强钢平整机的工作辊与支承辊辊径参数设计模型.其研究结果对指导宝钢分公司1880 mm热轧平整机的工艺参数的确定与技术谈判发挥了重要作用,并具有进一步的推广价值.     

火焰原子吸收法测定高铋物料中的铅

本文介绍了在以高铋物料为基体 ,5 %的HNO3 介质中 ,波长 2 17nm处进行火焰原子吸收法测定铅的试验 ,采用标准加入法进行回收率的试验 ,回收率大于 98% ,特征浓度为 0 .0 7μg/ml,结果令人满意 ,能满足炉前样分析的要求     

金属—PAN—S配合物的极谱研究——Ⅱ:Fe~(3+)—PAN—S—TEA—NH_3·H_2O—NH_4Cl体系配合吸附波

在NH_3·H_2O—NH_4Cl—三乙醇胺底液中Fe(Ⅲ)与PAN—S产生一灵敏的配合吸附波,峰电位在—0.50伏(vs.SCE)。峰电位与铁离子浓度在2.8×10~8～3.4×10~(-6)mol/L范围内线性良好,检出下限可达2.8×10~(-8)mol/L。该法用于乳粉、头发、血清等样品的测定,结果满意。     

柴达木盆地北缘的右行走滑冲断系统及其动力学

通过对于断裂系统分析和地球物理资料的解释,证实了柴达木盆地北缘西段的主要构造形成时间为上新世以后,变形样式为一系列右行走滑冲断构造。走滑冲断构造带内部的断层在平面上呈分支复合,剖面上表现为正花状构造,断层上、下盘地层层序无法直接对比。右行走滑冲断构造形成于南祁连由北向南的斜向推覆作用,而主要应力来源于柴达木地块北缘由南向北的陆内俯冲作用。用一个运动学模型解释了柴北缘的右行走滑冲断作用机制。     

Preparation of nanosized titania powder via the controlled hydrolysis of titanium alkoxide

By controlling the hydrolysis of titanium butoxide, followed with or without an ethanol washing process, the preparation of nanoscale titania powder was studied in detail. The characteristics of different powders produced by the direct precipitation (without an ethanol wash) and ethanol wash processes were studied by X-ray diffraction, transmission electron microscopy, BET, thermogravimetry and differential thermal analysis techniques. By comparison, it was found that both the direct precipitation and ethanol wash methods can obtain slightly agglomerated nanoscale titania powders of less than 15 nm, but the ethanol wash can further reduce the agglomeration. The particle sizes of titania powders can be modified while still retaining the anatase structure.     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

造纸机集散控制系统

本文介绍了造纸机集散控制系统．讨论了其硬件的组成和软件结构．研究了ＤＤＳ过程级控制器的功能及对造纸机各分部速度的优化控制．系统投人运行后，取得较好的经济效益．