含氮化合物废气选择性催化氧化技术研究进展

通过对当前含氮化合物废气治理技术的对比分析,总结选择性催化氧化的相关技术优势。根据对含氮化合物的种类及来源分析,介绍氨气、腈类、胺类及其他含氮化合物的催化净化技术。重点总结催化剂的种类、研发进展和在实际使用中可能遇到的问题,同时展望含氮化合物废气选择性催化氧化技术的研发方向。     

Simple approximations of the DC flux influence on the core losspower electronic ferrites and their use in design of magnetic components

The effect of DC flux on the core loss is examined for the practical range of power and frequency. Relevant core loss equations are derived and applied to an optimization algorithm to determine the minimum core loss at a given ratio of s (DC flux density to AC peak flux density). It has been found that the curves of hysteresis loss density versus the ratio of s exhibit a peak at a critical ratio. Below or above this critical ratio, the loss density decreases drastically. On the other hand, the curves of eddy-current loss density versus the ratio of s exhibits a minimum point at a critical ratio. Below or above this critical ratio, the loss density increases gradually     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

灌溉水库水资源优化调度

以榆社云簇水库为例、以水库灌区多种作物所能达到的最大产值为目标函数，本文研究了一套灌溉水库用水优化调度模型。它包括计划调度模型和实时调度模型两部分，适用于干旱半干旱地区灌溉水量不足的水库的用水调度。     

金刚石排锯及其合理使用

本文分析总结了锯切加工大理石、花岗石、毛板的金刚石排锯条的安装,使用原则,研究了金刚石刀头的配方,结构等质量性能。     

皮革真空鞣制新技术与设备的研究

本文对皮革在真空状态下鞣制进行了试验研究，使鞣制过程的物理—化学氛围得到改善，大大缩短了鞣制时间，废液排放量减少一半以上。     

脉冲啁啾对干涉相关测宽的影响及其消除方法

本文深入讨论了脉冲啁啾的非线性起源及其对干涉相关测宽(等值宽度和条纹计数)法的影响。提出根据干涉相关曲线下包络最大值位置适当降低等值宽度位置和用计算机平均处理干涉相关信息的技术以消除啁啾的影响。     

Hydrothermal Synthesis of Acicular Lead Titanate Fine Powders

A pure, acicular lead titanate (PbTiO₃) fine powder with a white color has been prepared by hydrothermal synthesis. It is a new phase of PbTiO₃ with I 4 symmetry, cell parameters of a = 12.358 Å and b = 14.541 Å, and a density of 6.80 g.cm⁻³. The influences of pH (12.5 to 14.4), Pb/Ti ratio (1.0 to 1.6) in the feedstock, reaction temperature (130° to 230°C), time (0.25 to 4 h), starting materials, and additives on the formation of acicular PbTiO₃ under hydrothermal conditions have been investigated. The acicular PbTiO₃ with I 4 symmetry, referred to as the PX phase, can be converted to the perovskite-type (PE phase) of PbTiO₃ at about 605°C while its acicular morphology is essentially unchanged. The preferable conditions for preparing pure acicular PX-phase PbTiO₃ are that the pH is 13.0 to 14.0, Pb/Ti ratio is >1.3, reaction temperature is 170° to 200°C, time is 0.5 to 1.0 h, titanium butoxide (Ti[O(CH₂)₃CH₃]₄) is the starting material, and poly(vinyl alcohol) is an additive. The acicular grain of the PX phase is usually less than 100 nm in diameter and more than 1000 nm in length.     

单相电焊机计量异常分析

针对单相电焊机采用单相感应式电能表进行计量中出现的圆盘反转现象 ,从理论和试验 2个方面分析和验证了 :由于单相电焊机本身的特点 ,无论它在负载还是空载状态 ,总会有 1块电能表出现圆盘反转 ,这是正常的     

Dipole radiation in the proximity of a chiral slab

Radiation of an electric dipole located along an arbitrary direction in the presence of a chiral slab is formulated using matrix analysis in conjunction with Fourier transform techniques. Moreover, dyadic Green's function of such a structure may be determined for further investigation porpose.