基于80C51F005单片机数据采集系统设计

文章阐述了一种利用新型集成数据采集芯片C8051F005来设计数据采集系统的思路。相对于一般的设计方法，由于其集成度高，且采用了高性能的闪速／电擦除存储器技术，能灵活地对芯片进行编程，方便地解决了数据采集问题，大大降低了数据采集系统的开发时间和系统成本。     

表冷器设计计算的一种新方法

本文从分析盘管内、外侧换热系数着手，提出了表冷器一种新的热工计算方法。     

单壁碳纳米管的制备及生长特性研究

采用Fe/MgO作为催化剂 ,催化裂解CH4制备了较纯的单壁碳纳米管 ,用TEM和Raman对碳纳米管进行了表征 ,对不同生长温度下制备的碳纳米管Raman径向呼吸振动峰 (RBM)进行了分析 ,研究了生长温度对单壁碳纳米管生长特性和结构特性的影响     

Calciothermic reduction of titanium oxide in molten CaCl<Subscript>2</Subscript>

Titanium oxides were reduced to metallic titanium using the liquid calcium floating on the molten CaCl₂. A part of Ca dissolved into CaCl₂ and reacted with TiO₂ settled below CaCl₂. The by-product CaO also dissolved by about 20 mol pct into CaCl₂, which was effective in reducing the oxygen concentration in the obtained Ti particles. The compositional region in the Ca-CaCl₂-CaO system was examined for the less oxygen contamination in Ti and the better handling in leaching. A large amount of the residual calcium oxidized the titanium powder in leaching. The metallic Ti powder less than 1000 mass ppm oxygen could be obtained only for 3.6 ks using 5 to 7 mol pct Ca-CaCl₂ at 1173 K. The powder was slightly sintered like sponge, and contained approximately 1500 ppm Ca. The anatase phae, the intermediate product in the refining process of TiO₂, could be also supplied as raw material as well as rutile.     

The electrochemical behaviour of nitrogen-containing austenitic stainless steel in methanolic solution

The corrosion behaviour of nitrogen-containing austenitic stainless steel in methanol containing different concentrations of H₂SO₄, HCl, LiCl and H₂SO₄ + HCl has been investigated using a potentiostatic polarization method. The cathodic reaction in the H₂SO₄, HCl and H₂SO₄ + HCl solutions was proton reduction whereas in the neutral LiCl solution, oxygen reduction was the predominant cathodic reaction. Active, passive and transpassive behaviours were observed only for higher concentrations of H₂SO₄ (0.01–2.0 M) due to the inherent water content. A cathodic loop, characterized by measured negative current in the anodic region, was also observed in solutions, in which the concentration of H₂SO₄ was 1.0 M or higher. The relative stability of the passive films decreased as the H₂SO₄ concentration increased, and thus the steel suffered from mild pitting corrosion. In the chloride environment, the rate of corrosion increased as the Cl⁻ ion concentration increased. The presence of acid along with Cl⁻ ions enhanced corrosion, and the corrosion rate increased significantly. The steel suffered from mild intergranular corrosion in acidic chloride solutions of methanol. In the H₂SO₄ + HCl solutions, passive films were only formed when the H₂SO₄ to HCl concentration ratio was greater than ∼10:1.     

Deposition and Properties of Superconducting MgB2 Thin Films

The recently discovered superconductor MgB₂ with T _c at 39 K has great potential in superconducting electronics. In this paper, we review the deposition techniques used for MgB₂ thin films in the light of a thermodynamic study of the Mg-B system with the calculation of phase diagrams (CALPHAD) modeling technique. This thermodynamic study identifies a growth window in the pressure–temperature phase diagram, in which the magnesium pressure is very high for likely in situ growth temperatures. A Hybrid Physical–Chemical Vapor Deposition (HPCVD) technique that successfully achieves such a high Mg pressure is shown to produce in situ epitaxial MgB₂ thin films with bulk superconducting properties.     

Physiology of spinal anaesthesia and practical suggestions for successful spinal anaesthesia

There are numerous physiological effects of spinal anaesthesia. This chapter focuses on the physiological effects that are of clinical relevance to the anaesthesiologist, and provides suggestions for successful management of this simple and popular technique. The mechanisms and clinical significance of spinal-anaesthesia-induced hypotension, bradycardia and cardiac arrest are reviewed. The increasing popularity of ambulatory spinal anaesthesia requires knowledge that long-acting local anaesthetics, such as bupivacaine, impair the ability to void far longer than short-acting local anaesthetics, such as lidocaine. The importance of thermoregulation during spinal anaesthesia, and the clinical consequences of spinal-anaesthesia-induced hypothermia are reviewed. Effects of spinal anaesthesia on ventilatory mechanics are also highlighted. Lastly, the sedative and minimum-alveolar-concentration-sparing effects of spinal anaesthesia are discussed to reinforce the need for the judicious use of sedation in the perioperative setting.     

油库防爆电气设备运行安全管理注意事项

分析了油库防爆电气设备运行中安全管理应注意的几个事项。     

计算机辅助维修性设计与分析中的版本管理

为了支持渐进的和探索武的维修性设计与分析过程，必须进行有效的版本管理。本文研究了维修性CAD框架中版本管理的设计方案以及实现过程。     

Nanocrystalline Ni coatings strengthened with ultrafine particles

In this study, nanocrystalline Ni powders and thermally sprayed coatings, containing ultrafine AlN particles, were synthesized and characterized. The results indicated that the presence of AlN particles in the powders drastically decreased the dimension of agglomerates formed by cryomilling and increased the surface roughness of the agglomerates. The AlN phase was broken down into ultrafine particles of approximately 30 nm in size. These particles were dispersed in the Ni matrix and enhanced the development of a nanocrystalline structure in the Ni matrix during cryomilling. Selected-area diffraction patterns, obtained from transmission electron microscopy (TEM) and X-ray mapping with scanning electron microscopy (SEM), confirmed the presence of AlN particles in the coatings. The presence of AlN particles also led to an increase in the amount of NiO phase that was distributed in the coating, in the form of ultrafine, round particles. AlN particles increased the microhardness of the Ni coating by approximately 60 pct. Indentation-fracture results also indicated that the fine, dispersed AlN particles raised the apparent toughness of the Ni coating. The synthesized Ni coatings containing ultrafine AlN particles were characterized as equiaxed nanocrystalline grains with an average size of 24 nm, in which twins were observed. The increase in microhardness resulted from both grain refinement and the presence of ultrafine particles. The latter played the primary role in strengthening.