影响喷气燃料与橡胶相容性的因素

采用几种具有不同初始物理性能及不同丙烯腈含量、不同硫化剂和硫化程度的丁腈橡胶，考察了其配方和物理性能对采用不同工艺条件生产的喷气燃料的相容性。结果表明，喷气燃料与橡胶的相容性不仅与喷气燃料的加工工艺有关，而且与橡胶的组成及其制备工艺有关。采用非加氢工艺生产的喷气燃料与橡胶的相容性好于采用加氢工艺(特别是加氢裂化工艺)生产的喷气燃料。橡胶材料的初始力学性能的好坏并不完全决定其与喷气燃料相容性的好坏，橡胶材料的耐过氧化物侵蚀能力才是影响相容性好坏的主要因素。橡胶的组成和其制备工艺决定了橡胶在喷气燃料中萃取物的数量和组成，不同萃取物的综合作用给相容性带来不同程度的影响。用硫作硫化剂的橡胶虽然原始强度低于用过氧化物作硫化剂的橡胶，但前者与喷气燃料的相容性却远好于后者。     

Magnetic Resonance Visualisation of Flow and Pore Structure in Packed Beds with Low Aspect Ratio

Different NMR techniques were combined to obtain the structure and velocity information for a systematic investigation of fixed beds with low aspect ratio (tube diameter to particle diamter, d_t/d_p) in the range 1.4 to 32. The structure of the void space was determined for a variety of packed beds of glass beads or regular and irregular porous pellets by magnetic resonance imaging (MRI). Based on the images the radial distribution of the voids within the bed was obtained. Ordering effects were found even for non‐spherical and polydisperse particles, and a maximum of the fluid density near the tube wall was confirmed for all pellet geometries and sizes. By combining MRI with velocity encoding, velocity profiles and distributions of flow velocity components of a single fluid phase through packed beds have been acquired. The radial velocity distribution follows an oscillatory pattern which largely reflects the ordering of the particles, which can be accessed from the density distribution of the interparticle fluid. Maximum velocities of up to four times the average value were found to occur near the tube wall. This wall effect was observed for all but the smallest particles, where the aspect ratio was d_t/d_p = 32. Moreover, a visualisation of flow pattern in the presence of packed particles was achieved by using a tagging technique, and the stationary flow field could be identified for an experimental time of several hours.     

无氢类金刚石碳膜的研究进展

介绍了无氢类金刚石碳膜的制备方法 ,它们的机械、光学、电学性能 ,将无氢与含氢的类金刚石碳膜进行了简单比较 ,总结及探讨了它们的应用     

长链烯烃-苯烷基化反应的分子筛催化剂再生性能的研究

通过热重分析和活性稳定性评定考察催化剂的再生性能。研究结果表明,进行氯气吹扫以及苯抽提后进行氮气吹扫两种预处理,导致失活催化剂的起燃点和烧焦反应活化能均有所提高,有利于控制烧焦反应速度。按苯抽提、氮气吹扫、烧焦的顺序,分三个阶段进行催化剂再生,再生催化剂的活性稳定性得到更充分的恢复。     

飞行人员骨密度与内分泌调节关系的探讨

对37名骨密度(BD)低下的飞行员(实验组)和BD正常的48名飞行员、100名地面人员(正常对照组)进行了BD和血清TT_3、TT_4、TSH IRMA、CT、PTH、E_2和T放射免疫测定。结果显示,实验组BD均值明显低于对照组(p<0.01),血清TT_3、TT_4、CT、E_2(女性)和T(男性)均值与对照组比较,大多数年龄存在着显著或非常显著差异(p<0.05或p<0.01)。同时对飞行人员BD与几种内分泌激素关系进行了探讨。     

葡萄糖电解氧化还原工艺研究

采用自制的无膜电解槽，对同时电解氧化还原葡萄糖生成葡萄糖酸和山梨醇的工艺进行了研究。所得到的最佳工艺条件为：葡萄糖浓度０．４ｍｏｌ／Ｌ，ｐＨ值１１，电流密度３Ａ／ｄｍ￣２。在此条件下电解１２ｈ，葡萄糖转化率可达９６．４％，葡萄糖酸产率８８％，山梨醇产率１０％。同时，考察了和Ｚｎ￣（２＋）加入以及ｐＨ值对电流效率的影响。     

P偏振光双表面反射比的角谱及其应用

p-偏振光在镀膜平板基片两面的反射光强度比值的角谱是膜层参数(折射率、消光系数和厚度)的函数.实验表明通过角谱的测量和数值模拟是精确测量薄膜参数的新途径.基于此原理,还试制出掺Sb的SnO2溶胶凝胶薄膜的光化学气敏传感器.     

Effects of Sc2O3 and MgO passivation layerson the output power of AlGaN/GaN HEMTs

The low temperature (100°C) deposition of Sc₂O₃ or MgO layers is found to significantly increase the output power of AlGaN/GaN HEMTs. At 4 GHz, there was a better than 3 dB increase in output power of 0.5×100 μm² HEMTs for both types of oxide passivation layers. Both Sc₂ O₃ and MgO produced larger output power increases at 4 GHz than conventional plasma-enhanced chemical vapor deposited (PECVD) SiN_x passivation which typically showed ⩽2 dB increase on the same types of devices. The HEMT gain also in general remained linear over a wider input power range with the Sc₂O₃ or MgO passivation. These films appear promising for reducing the effects of surface states on the DC and RF performance of AlGaN/GaN HEMTs