14 nm FinFET栅围寄生电容的建模与拟合

提出了一种基于保角映射方法的14 nm鳍式场效应晶体管(FinFET)器件栅围寄生电容建模的方法。对FinFET器件按三维几何结构划分寄生电容的种类,再借助坐标变换推导出等效电容计算模型,准确表征了不同鳍宽、鳍高、栅高和层间介质材料等因素对寄生电容的依赖关系。为了验证该寄生电容模型的准确性,对不同结构参数的寄生电容进行三维TCAD仿真。结果表明,模型计算结果与仿真结果的拟合度好,准确地反映了器件结构与寄生电容之间的依赖关系。     

Effects of testing configurations and cell geometries on the performance of a SOFC: A modeling approach

A two-dimensional electrochemical model including mass and charge transfer has been developed to illustrate the effects of testing configurations and cell geometries on SOFC’s performance. The model is favorably validated by the well agreeable experimental results. It is shown that the separation of anode and cathode overpotential by three-electrode method is essentially impractical for anode-supported SOFCs. It is also found that testing configuration has little effect on cell performance due to the high electrical conductivity in anode. Furthermore, because the effective resistance of electrolyte is lower for asymmetric cells than for symmetric cells, cell performance of a symmetric cell is smaller than that of an asymmetric cell. Discrepancy in cell performance is shown to increase with increasing the thickness of electrolyte or decreasing the cathode radii.     

15%三唑磷微乳剂配方研制及其田间药效

采用反相法研制15%三唑磷微乳剂,所得制剂在54℃下热贮14d分解率小于5%,室温下2a分解率小于5%,透明区域为-30~100℃,稀释稳定性及低温稳定性合格,药效优于20%三唑磷乳油。     

一类n维Lotka—Volterra模型的稳定性特征

本文给出n维Lotka-Volterra合作系统局部渐近稳定性和全局稳定性的判别条件,并证明该系统正平衡位置的稳定性特征:局部渐近稳定性和全局稳定性是等价的.     

纳米BaTiO3的Sn掺杂改性与性能研究

通过溶胶凝胶法制备了掺锡钛酸钡前驱体并进行了粉末和陶瓷样品制备,分析了掺杂Sn比例对BaTi1-xSnxO3粉末和陶瓷物相组成、微观形貌和铁电性能的影响.结果 表明,不同Sn掺杂比例下BaTi1-xSnxO3粉末的晶胞体积随着x值增加不断增大,当x=0.06时,BaTi0.94Sn0.06O3粉末中c/a值约等于1.009,为不同Sn掺杂比例下BaTi1-xSnxO3粉末中最大值;扫描电镜下,BaTi0.94Sn0.06O3粉末中颗粒的尺寸基本都在30μm以下,且基本呈四方结构.在x=0.06时,BaTi1-xSnxO3陶瓷中c/a值(1.021)和晶胞体积(65 166 nm3)为几组试样中最大值,表明BaTi0.94Sn0.06O3陶瓷中四方相晶型结构最显著.随着频率增加,BaTi1-xSnxO3陶瓷的剩余极化强度和矫顽场强都呈现逐渐减小特征,在相同频率下,BaTi0.94Sn0.06O3陶瓷的剩余极化强度最大、矫顽场强最小,具有最佳的铁电性能.     

压力容器局部区域的应力分析设计

就“99版”《压力容器安全技术监察规程》第 40条有关内容展开分析讨论 ,阐述按常规设计标准和分析设计标准设计计算时 ,材料许用应力、计算方法和判据以及最终应力控制水平方面的差异 ;并阐述这种设计方法在相互交错、相互组合时的处理方法 ;以及局部参照分析设计标准在分析计算中可能会遇到的一些问题。此外 ,还论述了站在 GB1 50常规设计立场上怎样正确理解和运用局部参照分析设计计算的观点和方法     

造纸黑液制水煤浆添加剂成浆性能的研究

针对淮化德士古气化炉所用的义马煤和鲁南化肥厂使用的配煤 ,进行了造纸黑液制添加剂实验室和工业制浆性能的考察。结果表明 ,其在工业应用中的添加量范围在 1.2 %～ 1.6 % (浆基 ,添加剂含固量 2 0 % ) ,对义马煤和鲁南配煤分别可以制出浓度在 6 4 .5 %和 6 9%之间 ,稳定性能良好 ,满足工业生产要求的水煤浆     

高结构导电炭黑填充硅橡胶复合材料的性能

研究了导电炭黑（ＨＧ－ＣＢ）的高结构对乙烯基甲基硅橡胶（ＶＭＱ－１１０）复合材料电性能和机构性能的影响。由ＴＥＭ观察看出,随ＨＧ－ＣＢ用量增加,其在硫化胶中形成的导电网络逐渐完善,用量达１９份（质量份,下同）时已形成完整的导电网络,导电机理可用电子隧道效应来解释,同时随ＨＧ－ＣＢ填充量增加,复合材料的拉伸强度、硬度增大,但对ＶＭＱ－１１０的硫化有影响。欠硫现象严重,ＨＧ－ＣＢ的用量一般控制在１０～１５份,所得硅橡胶复合材料具有较佳的电性能和机械性能。     

藏北高原地区和西北干旱区地表能量季节变化特征对比分析

基于中日合作研究项目"全球协调加强观测计划之亚澳季风青藏高原试验"(CAMP/Tibet,2001～2005年)和大型野外观测试验国家重点基础研究发展规划项目中的"西北干旱区陆气相互作用试验"(DHEX,2000-2003年) 1a年的观测数据资料分析研究了干旱区地表能量,即净辐射通量、感热通量、潜热通量和土壤热通量。得到一些有关地表能量的新认识,最后还提出并讨论了计算地表能量通量的方法及其优缺点。     

Sm0.2(Ce1−xTix)0.8O1.9 modified Ni-yttria-stabilized zirconia anode for direct methane fuel cell

Sm_0.2(Ce_1−xTi_x)_0.8O_1.9 (SCTx, x = 0-0.29) modified Ni-yttria-stabilized zirconia (YSZ) has been fabricated and evaluated as anode in solid oxide fuel cells for direct utilization of methane fuel. It has been found that both the amount of Ti-doping and the SCTx loading level in the anode have substantial effect on the electrochemical activity for methane oxidation. Optimal anode performance for methane oxidation has been obtained for Sm_0.2(Ce_0.83Ti_0.17)_0.8O_1.9 (SCT0.17) modified Ni-YSZ anode with SCT0.17 loading of about 241 mg cm⁻² resulted from four repeated impregnation cycles. When operating on humidified methane as fuel and ambient air as oxidant at 700 °C, single cells with the configuration of SCT0.17 modified Ni-YSZ anode, YSZ electrolyte and La_0.6Sr_0.4Co_0.2Fe_0.8O₃-Sm_0.2Ce_0.8O_1.9 (LSCF-SDC) composite cathode show the polarization cell resistance of 0.63 Ω cm² under open circuit conditions and produce a peak power density of 383 mW cm⁻². It has been revealed that the coated Ti-doped SDC on Ni-YSZ anode not only effectively prevents the methane fuel from directly impacting on the Ni particles, but also enhances the kinetics of methane oxidation due to an improved oxygen storage capacity (OSC) and redox equilibrium of the anode surface, resulting in significant enhancement of the SCTx modified Ni-YSZ anode for direct methane oxidation.