Enhancement mode InP MISFET's with sulfide passivation andphoto-CVD grown P3N5 gate insulators

High performance enhancement mode InP MISFET's have been successfully fabricated by using the sulfide passivation for lower interface states and with photo-CVD grown P₃N₅ film used as gate insulator. The MISFET's thus fabricated exhibited exhibited pinch-off behavior with essentially no hysteresis. Furthermore the device showed a superior stability of drain current. Specifically under the gate bias of 2 V for 10⁴ seconds the room temperature drain current was shown to reduce from the initial value merely by 2.9% at the drain voltage of 4 V. The effective electron mobility and extrinsic transconductance are found to be about 2300 cm ²/V·s and 2.7 mS/mm, respectively. The capacitance-voltage characteristics of the sulfide passivated InP MIS diodes show little hysteresis and the minimum density of interface trap states as low as 2.6×10¹⁴/cm² eV has been attained     

Einfluß der Korngröße auf mechanische Eigenschaften und den ungeschmierten reversierenden Gleitverschleiß von Al2O3-Keramik

Influence of grain size on mechanical properties and dry oscillating sliding wear of Al₂O₃-ceramics Specimens with average grain sizes varying between about 0.8 μm and 12 μm were produced by cold isostatic pressing of high purity Al₂O₃-powder followed by sintering between 1300°C and 1700°C. Hardness, Young's modulus, bending strength and fracture toughness were measured as a function of average grain sizes. Tribological tests were carried out on the different microstructures at normal laboratory air and room temperature by using a ring-on-block tribometer. Experimental results showed the dependence of mechanical properties on grain size, hardness and bending strength obeying a Hall-Petch type relation, approximately. Coefficient of friction was relatively independent of grain size under the test conditions used. However, wear intensity increased substantially if a critical grain size was surpassed. This was due to a change in mechanisms of material removal which was confirmed by scanning electron microscopical studies of the worn surfaces.     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.     

The design of experiments when there are errors in all the variables

The Error-in-Variables Model (EVM) applies to a large class of problems in parameter estimation in which there is error in all the variables. This property makes it of more general applicability than the widely used technique of ordinary Least Squares. While there is a voluminous literature on EVM there is nothing on a general method for designing experiments when EVM applies. In this paper we present an extension of the concept of D-optimality to provide such a general method. It is illustrated by applying it to the estimation of copolymer reactivity ratios and to fitting an ellipse.     

The prospects of non-volatile phase-change RAM

Phase-change read-and-write memory (PRAM) is a promising memory that can solve the problems of conventional memory—scalability, read/write speed, and reliability. We will review the opportunities and technical challenges of PRAM. The most important challenge of PRAM is the reduction of the writing current. Various approaches to reduce the writing current will be reviewed and the prospects of PRAM are discussed.     

From information to probability: An axiomatic approach—Inference is information processing

We define the very rich language of composed conditionals on a three‐valued logic and use this language as the communication tool between man and machine. Communication takes place for three reasons: knowledge acquisition, query, and response. Learning, thinking, and answering questions are of a pure information theoretical nature. The pivot of this knowledge processing concept is the amount of information (bit) we receive if a conditional becomes true. We follow an axiomatic approach to information theory rather than the classical probabilistic approach of Shannon; information comes first, and then comes probability. In the light of this philosophy, query and response experience new interpretations. Both, acquisition and response are realized by maximizing entropy and minimizing relative entropy, respectively. The iterative solution of these mathematical optimization problems gives new insights into the adaptation of prior knowledge to new information. Our expert system shell SPIRIT supports this kind of knowledge processing, which will be established by suitable examples. © 2003 Wiley Periodicals, Inc.     

Prediction of fire classification for wood based products. A multivariate statistical approach based on the cone calorimeter

Wood has long traditions as a building material, and is often used in construction elements, and as interior and exterior surfaces in the Nordic countries. In most applications, there are reaction to fire requirements to products used as surfaces, e.g. in escape routes and larger public spaces. Most wood products will therefore have to be treated with fire retardant (FR) agents to fulfil the strict requirements to properties connected to heat release and flame spread. Unfortunately, FR agents usually also increase the smoke production, as they cause a more incomplete combustion of the wood. The wood product manufacturers seek to find the optimal amount of FR additives where both heat release and smoke production in the classifying test are within the requirements given in the building regulations. This paper describes models for prediction of the European reaction to fire classes of wood products. The models are based on multivariate statistical analysis, and use test results from the cone calorimeter test as input. The presented models are, with very good precision, able to predict which Euroclass and additional smoke class a wood based product would obtain if it were to be tested in the single burning item test. Copyright © 2006 John Wiley & Sons, Ltd.     

Possibility of sewage and combined sewer overflow reuse with biological aerated filters.

The secondary effluent from municipal plants in Korea generally represents higher BOD with lower SS. Therefore, more soluble forms of organics and NH4-N need to be removed to improve its effluent for reuse. In this study reuse possibility of secondary effluent and CSO (combined sewer overflow) using BAF (biological aerated filter) was evaluated. The tertiary application with 1.2 h EBCT, SS, BOD and COD showed stable concentrations less than 1.3, 1.3 and 6.2 mg/L, respectively. Nitrogen could be nitrified even at 7 degrees suggesting BAF can be used for a water reuse method as well as an effective add-on facility in cold regions. However, BAF was not stable with CSO application at increased flow rates suggesting CSO must be equalised prior to application. Disinfection was necessary even during normal weather conditions.