An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Practical limitations of subwavelength resolution using negative-refractive-index transmission-line lenses

Previously, we have demonstrated both analytically and experimentally subwavelength imaging using a negative-refractive-index lens made of a periodically L, C loaded transmission line (TL) network. This loaded transmission line network has been referred to as the dual TL lens. Here, we consider the limitations on subwavelength imaging imposed by impedance mismatches and the component losses of a practical dual TL lens. Simple expressions for estimating the resolving capability of a dual TL lens are given. It is found that the resolution enhancement of the dual lens is proportional to the quality factor of the series loading capacitors divided by the electrical thickness of the lens. The effective material parameters of the dual TL lens are also derived so that these expressions can be directly related to those of previous studies considering uniform and isotropic left-handed lenses. Finally, the resolving capability of an experimental lens that achieves subwavelength imaging is theoretically predicted. These theoretical predictions are then directly compared to previously reported experimental results.     

Circuits and techniques for high-resolution measurement of on-chip power supply noise

This paper presents a technique for characterizing the statistical properties and spectrum of power supply noise using only two on-chip low-throughput samplers. The samplers utilize a voltage-controlled oscillator to perform high-resolution analog-to-digital conversion with minimal hardware. The measurement system is implemented in a 0.13-/spl mu/m process along with a high-speed link transceiver. Measured results from this chip validate the accuracy of the measurement system and elucidate several aspects of power supply noise, including its cyclostationary nature.     

Programmable analogue VLSI implementation for asymmetric sigmoid neural activation function and its derivative

A new CMOS VLSI implementation of an asymmetric programmable sigmoid neural activation function, as well as of its derivative, is presented. It consists of two coupled PMOS and NMOS differential pairs with different programmable bias currents that set the upper and lower limits of the sigmoid. The circuit works in the weak inversion region, for low power consumption and exponential envelope, or in strong inversion to achieve higher speeds. The results obtained from the theoretical transfer function, and from the simulations of the circuit implemented in AMI's 0.35 /spl mu/m technology, show a very good match.     

Dynamic vulcanisation of EPDM/PE-based thermoplastic vulcanisates studied along the extruder axis

Simple blending and dynamic vulcanisation of EPDM/PE blends using the resol/SnCl₂ system was studied in an extruder using a series of sampling devices. The melting of the PE pellets occurs just in front of and in the first kneading zone. Upon complete melting of the PE phase, the EPDM/PE blends reach very quickly their final morphology. Crosslinking of the EPDM phase to high levels occurs already when the PE phase is not yet fully molten. The higher the EPDM content, the higher the viscous dissipation, the higher the melt temperature and, consequently, the higher the crosslinking rate. For the EPDM/PE (50/50; w/w) TPV a transition from continuous via co-continuous to fully dispersed EPDM is observed, which is driven by crosslinking. Although the degree of crosslinking of the EPDM rubber is very high, this does not prevent phase inversion of the blend. The EPDM/PE interface is rather blurred, because PE crystalline lamellae are growing into the EPDM domains, probably because of the high compatibility between PE and EPDM (60 wt% of ethene). This study shows that dynamic vulcanisation in extruders proceeds quite differently from that in batch kneaders, where melting, mixing and crosslinking are separated in time. In extruders mass and heat transport, melting of the thermoplastic, morphology development (including dispersion and phase inversion), distribution and dissolution of (crosslinking) chemicals and crosslinking of the rubber do not occur as independent phenomena, but mutually and/or continuously interact.     

Polyimide foams from powder: Experimental analysis of competitive diffusion phenomena

In the present study, various diffusive processes have been investigated during foaming of powdered precursors of polyimide. A detailed analysis of the powdered precursor's characteristics allows for an enhanced morphological understanding of the resulting microstructures and foam unit cell. Parameters that are central to the foaming process such as particle morphology, volatile concentration and sorption-desorption processes are evaluated. Isothermal and non-isothermal desorption experiments have been carried out by thermogravimetric analysis (TGA), and specific diffusive processes have been correlated to thermodynamic and kinetic transitions by means of modulated differential scanning calorimetry (MDSC) of the corresponding materials. It was found that two primary fluxes of volatiles, one out of the external surface of the particles (responsible for volatile desorption) and the other into the growing bubble (responsible for vapor supersaturation inside the bubble) compete against each other creating a competitive scenario that becomes the controlling factor for potential inflation within the precursor particles.     

Optimal design and manufacture of thin‐walled polystyrene structures

In this study, we investigated the implementation of an automatic procedure for optimizing thermoformed thin‐walled structures. Such objects are created in great numbers, especially in the food packaging industry. The methodology for the optimal design of such structures is based on the use of a parameterized geometry model created within an interactive design environment. By varying the parameters associated with the computer‐aided design (CAD) model, one can create a rich variety of possible designs. One can then subject these designs to physical analysis to calculate their physical properties, and thus select an optimal design. The two distinct stages of this process—the prediction of the shape of the thermoformed structure, and the physical behavior of the structure—were validated by experiments. This article reports the experimental investigation of the deformation behavior of polystyrene, the mechanical behavior of specially prepared deformed polystyrene sheets, and the response to loading of a hemispherical structure (used in the validation). POLYM. ENG. SCI., 45:694–703, 2005. © 2005 Society of Plastics Engineers     

Dynamics of plastic polygonal plates with rounded corners

A method of calculating the dynamic deflection of rigidly plastic plates resting on a viscoelastic bed with complex piecewise-smooth support contours composed of sections of straight lines and circles under impact and explosion loading is presented. The general solution, which includes previously known partial solutions for circular and polygonal plates, is obtained. The results of calculation of the deflection of a square hinge-supported plate with rounded corners are presented for the case of the presence and absence of a plastic base.Translated from Problemy Prochnosti, No. 9, pp. 62–66, September, 1991.     

The state of stress and strain of an elastic cylindrical shell under acoustic action

The article investigates the state of stress and strain of the surface of an elastic cylindrical shell whose outer part is subjected to the effect of an incident acoustic wave. A qualitative and quantitative analysis of the state of strain of the surface is carried out and recommendations are given for optimizing the functional purpose of the shell and minimizing the arising stresses.Translated from Problemy Prochnosti, No. 4, pp. 43–47, April, 1991.