2-D symmetry: theory and filter design applications

In this comprehensive review article, we present the theory of symmetry in two-dimensional (2-D) filter functions and in 2-D Fourier transforms. It is shown that when a filter frequency response possesses symmetry, the realization problem becomes relatively simple. Further, when the frequency response has no symmetry, there is a technique to decompose that frequency response into components each of which has the desired symmetry. This again reduces the complexity of two-dimensional filter design. A number of filter design examples are illustrated.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

Motive Force in a Complex Model of Mass Transfer

Relations for determining a motive force in a complex model of mass transfer as applied to concurrent, countercurrent, and cross motion of the vapor and liquid phases have been introduced. These forces have been compared for different forms of organization of the flow, and their comparison with similar quantities from the known Murphree and Hausen models is presented.     

Interior symmetry and local bifurcation in coupled cell networks

A coupled cell system is a network of dynamical systems, or 'cells', coupled together. Such systems can be represented schematically by a directed graph whose nodes correspond to cells and whose edges represent couplings. A symmetry of a coupled cell system is a permutation of the cells and edges that preserves all internal dynamics and all couplings. It is well known that symmetry can lead to patterns of synchronized cells, rotating waves, multirhythms, and synchronized chaos. Recently, the introduction of a less stringent form of symmetry, the 'symmetry groupoid', has shown that global group-theoretic symmetry is not the only mechanism that can create such states in a coupled cell system. The symmetry groupoid consists of structure-preserving bijections between certain subsets of the cell network, the input sets. Here, we introduce a concept intermediate between the groupoid symmetries and the global group symmetries of a network: 'interior symmetry'. This concept is closely related to the groupoid structure, but imposes stronger constraints of a group-theoretic nature. We develop the local bifurcation theory of coupled cell systems possessing interior symmetries, by analogy with symmetric bifurcation theory. The main results are analogues for 'synchrony-breaking' bifurcations of the Equivariant Branching Lemma for steady-state bifurcation, and the Equivariant Hopf Theorem for bifurcation to time-periodic states.     

Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar

The main objective of this present study was to evaluate, for a standard mortar, the drying effect on its mechanical behaviour. Numerous uniaxial compression tests were thus performed with loading-unloading cycles. They were carried out on different samples previously preserved under various conditions of conservation: preserved from desiccation, air drying and rapid drying at 60°C. The obtained results showed significant influences of these conditions on the material behaviour (increase in strength, decrease in Young's modulus and Poisson's ratio) and the necessity of taking into account the coupling effects between mechanical—poromechanical behaviours and drying.     

Trajectory control of incompletely restrained parallel-wire-suspended mechanism based on inverse dynamics

This paper discusses parallel wire mechanisms where an end-effector of the mechanism is suspended by multiple wires. The mechanisms enable not only three-dimensional (3-D) positioning but also 3-D orienting of the end-effector, unlike typical wire suspension-type mechanisms such as overhead crane. To discuss the parallel-wire-suspended mechanisms generally, two forms of basic dynamic equations are presented. Then the parallel wire mechanisms are classified into two types based on the basic equations. Dynamical properties of the two types of wire-suspended positioning mechanism are discussed. In this paper, one of the wire-suspended mechanism, incompletely restrained-type parallel wire mechanism, is mainly discussed on its inverse dynamics problem and its trajectory control problem. The inverse dynamics problem for the incompletely restrained-type mechanism plays an important role on its control problem, because the mechanism has low stiffness based on incomplete constraints on the suspended object which is governed by its dynamics. The paper proposes an antisway control method for the suspended object. In the method, the inverse dynamics calculation is used for nonlinear dynamics compensation to control the suspended object of the incompletely restrained parallel wire mechanism.     

NEXUS — Resilient Intelligent Middleware

Service-oriented computing is the latest software paradigm brought about by the computing revolution. The different viewpoint and granularity of software components used in technologies based on the service-oriented architecture paradigm, compared to traditional object-oriented methodologies makes them better suited to many of the efforts that are being made in the pervasive and ubiquitous computing world. In the NEXUS project we are seeking ways of fusing the SOA and pervasive computing paradigms in order to build intelligent, robust and resilient networks connecting dynamic islands of service resources.     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.