Clay compaction modelling by homogenization theory

The modelling of hydromechanical behavior of clayey sediments by homogenization theory is described. The rheological model of clays buried in depth requires a three-dimensional approach and laboratory experiments to quantify the model parameters. An iterative process which can be coupled to any homogenization method is used to model the porous media behavior. Hydromechanical compaction results from oedometric experiments are simulated with the proposed model.     

Fractographic and numerical study of hydrogen–plasticity interactions near a crack tip

This paper offers a fractographic and numerical study of hydrogen–plasticity interactions in the vicinity of a crack tip in a high-strength pearlitic steel subjected to previous cyclic (fatigue) precracking and posterior hydrogen-assisted cracking (HAC) under rising (monotonic) loading conditions. Experiments demonstrate that heavier cyclic preloading improves the HAC behaviour of the steel. Fractographic analysis shows that the microdamage produced by hydrogen is detectable through a specific microscopic topography: tearing topography surface or TTS. A high resolution numerical modelling is performed to reveal the elastoplastic stress–strain field in the vicinity of the crack tip subjected to cyclic preloading and subsequent monotonic loading up to the fracture instant in the HAC tests, and the calculated plastic zone extent is compared with the hydrogen-assisted microdamage region (TTS). Results demonstrate that the TTS depth has no relation with the active plastic zone dimension, i.e., with the size of the only region in which there is dislocation movement, so hydrogen transport cannot be attributed to dislocation dragging, but rather to random-walk lattice diffusion. It is, however, stress-assisted diffusion in which the hydrostatic stress field plays a relevant role. The beneficial effect of crack-tip plastic straining on HAC behaviour might be produced by the delay of hydrogen entry caused by residual compressive stresses and by the enhanced trapping of hydrogen as a consequence of the increase of dislocation density after cyclic plastic straining.     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

The radiative recombination coefficient and the internal quantum yield of electroluminescence in silicon

The results of the analysis of variations in the radiative recombination coefficient with varying doping level and concentration of excess electron-hole pairs are reported. It is shown that, along with the effect of narrowing of the band gap calculated in the many-electron approximation, the effect of screening of the Coulomb interaction responsible for the decrease in the excition binding energy should be taken into account. Both effects produce similar trends and decrease the radiative recombination coefficient with increasing levels of doping or injection. The contributions of excitonic radiative recombination and band-to-band radiative recombination to the total radiative recombination coefficient are separated from each other. It is shown that, in the region of room temperature, both contributions are comparable, while at liquid-nitrogen temperature, the excitonic component dominates over the band-to-band component. The results obtained by refined calculations of the limiting value of the internal quantum yield of electroluminescence for the silicon diodes and p-i-n structures are presented. It is shown that the internal quantum yield of electroluminescence can be as high as 14%. However, this values sharply decreases with increasing surface recombination rate and decreasing lifetime of excess charge carriers in the bulk.     

Radioecological state of the territory and water area in Guba Andreev

The radioecological conditions which developed on the territory over the long operating time of the object of the naval fleet in Guba Andreev are described. The results of an analysis of the sources of the real and potential danger and measures to prevent dangerous effects for the environment and the workers at the time remediation work is performed are discussed. __________ Translated from Atomnaya énergiya, Vol. 101, No. 1, pp. 49–55, July, 2006.     

A prototype of a superconducting magnet for a 170-GHz gyrotron

Within the framework of the “International Thermonuclear Experimental Reactor” (ITER) program, a prototype of a superconducting magnet for a 170-GHz gyrotron has been developed, manufactured, and tested. The operating induction value (7.1 T at the center of a 219-mm-diameter cold hole and 8.1 T on the winding) is reached at a current of 185.2 A. In the final version of the magnet, the required induction value was reached without aging. Special requirements are imposed on the distribution of the magnetic field along the axis, including an abrupt field decrease on both sides of the magnet. Axial forces are additionally taken by a special device. The magnet’s sections are wound with multifiber conductors based on niobium-tin and niobium-titanium alloys. Seventeen resistive shunts are provided for protecting sections during their transition to the normal state. The magnet is equipped with a device for removing a part of energy from the sections. Mechanical stresses in the magnet’s sections and the structure’s power elements have been measured during tests.     

A device for measuring the equivalent resistance of an energized circuit section

A device for measuring the active resistance of a direct current energized circuit section is described. Owing to the use of up-to-date electronic components, an iteration measurement algorithm, and a sinusoidal signal as a test one, the following performance characteristics have been obtained: the measurement time is <1 s, and the error varies from 0.3 to 2.0% in a 100-Ω to 1-MΩ range and ≤25% in 10-to 100-Ω and 1-to 10-MΩ ranges.     

Effect of ultrasonic treatment on photoelectric and luminescent properties of ZnSe crystals

The results of the effect of ultrasonic treatment of ZnSe crystals on the structure of the energy spectrum of electronic states of centers with deep levels forming photoelectric and luminescent properties of this compound are presented. It is for the first time proved experimentally that the climb of edge dislocations under the effect of ultrasound leads to regrouping and generation of defects forming deep levels, which manifest themselves in phenomena of photosensitivity and radiative recombination.     

Tri-Gate Bulk MOSFET Design for CMOS Scaling to the End of the Roadmap

A tri-gate bulk MOSFET design utilizing a low-aspect-ratio channel is proposed to provide an evolutionary pathway for CMOS scaling to the end of the roadmap. 3-D device simulations indicate that this design offers the advantages of a multi-gate FET (reduced variability in performance and improved scalability) together with the advantages of a conventional planar MOSFET (low substrate cost and capability for dynamic threshold-voltage control).     

Identification of the temperature field and stresses in a thermosensitive cylinder according to the surface strains

We identify the time dependence of temperature of a surface of a long hollow thermosensitive cylinder and its thermal and thermal stressed states according to the known temperature and strains on the other surface. The posed problem is reduced to the inverse problem of thermoelasticity. By using the solution of the direct problem of thermoelasticity, we perform the numerical verification of the proposed procedure of solution of the inverse problem. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 43, No. 6, pp. 55–61, November–December, 2007.