Comparison of stress field forming methods for vibro-acoustography

Vibro-acoustography is a method that produces images of the acoustic response of a material to a localized harmonic motion generated by ultrasound radiation force. The low-frequency, oscillatory radiation force (e.g., 10 kHz) is produced by amplitude modulating a single ultrasound beam, or by interfering two beams of slightly different frequencies. Proper beam forming for the stress field of the probing ultrasound is very important because it determines the resolution of the imaging system. Three beam-forming geometries are studied: amplitude modulation, confocal, and x-focal. The amplitude of radiation force on a unit point target is calculated from the ultrasound energy density averaged over a short period of time. The profiles of radiation stress amplitude on the focal plane and on the beam axis are derived. The theory is validated by experiments using a small sphere as a point target. A laser vibrometer is used to measure the velocity of the sphere, which is proportional to the radiation stress exerted on the target as the transducer is scanned over the focal plane or along the beam axis. The measured velocity profiles match the theory. The theory and experimental technique may be useful in future transducer design for vibro-acoustography.     

Improved parametric imaging of scatterer size estimates using angular compounding

The feasibility of estimating and imaging scatterer size using backscattered ultrasound signals and spectral analysis techniques was demonstrated previously. In many cases, size estimation, although computationally intensive, has proven to be useful for monitoring, diagnosing, and studying disease. However, a difficulty that is encountered in imaging scatterer size is the large estimator variance caused by statistical fluctuations in echo signals from random media. This paper presents an approach for reducing these statistical uncertainties. Multiple scatterer size estimates are generated for each image pixel using data acquired from several different directions. These estimates are subsequently compounded to yield a single estimate that has a reduced variance. In this feasibility study, compounding was achieved by translating a sectored-array transducer in a direction parallel to the acquired image plane. Angular compounding improved the signal-to-noise ratio (SNR) in scatterer size images. The improvement is proportional to the square root of the effective number of statistically independent views available for each image pixel.     

Initial perspectives on process threat management

Terrorist and criminal acts are now considered credible risks in the process industries. Deliberate attacks on the nation's petroleum refineries and chemical plants would pose a significant threat to public welfare, national security, and the US economy. To-date, the primary response of government and industry has been on improved security to prevent attacks and the associated consequences. While prevention is clearly preferred, the potential for successful attacks must be addressed. If plant security is breached, the extent of the inflicted damage is determined by the available plant safety systems and procedures. We refer to this "inside the gate" response as process threat management. The authors have initiated a joint industry/academia study to address: the level of safety provided by existing plant equipment and safety systems in response to a terrorist act, and identification of process (rather than security) needs or opportunities to address this new safety concern. This paper describes the initial perspectives and issues identified by the team at the beginning of the study.     

A torsional transducer through in-plane shearing of paired planar piezoelectric elements

A torsional microtransducer for high-power applications was developed using standard bulk lead zirconium titantate (PZT) placed upon a small rectangular prism made from phosphor bronze, with a tapered conical end serving as a horn and a machined interior to improve the actuator's response. Torsion was obtained from a prototype at the design frequency of 192 kHz as well as over a wide range of frequencies from 136 kHz to 1.02 MHz. Torsional vibration velocities of 335 mm/s at 192 kHz were measured at 27.3 V(RMS) on the 1.5-mm diameter output tip, amounting to 25,600 degree/s vibration velocity along the outer circumference of the tip. At 1.02 MHz, a torsional vibration velocity of 1750 mm/s (134,000 degree/s) at 17.8 V(RMS) was obtained through use of the thickness mode of the PZT elements. Using the design described in this study, high-power torsional transducers with diameters of 5 mm and below are now possible.     

Thermal characterization of PMMA-based bone cement curing

In thermal characterization tests of polymethylmethacrylate bone cement performed according to the ASTM Standard Specification for Acrylic Bone Cement, time-temperature profiles of bone cement were observed to be sensitive to the thickness of the cement patty and the mold material. Due to the heat transfer from cement to the surrounding mold, such tests might underestimate the exothermic temperature of bone cement. Developing test methods to better characterize cement thermal behavior is necessary for accurate cement curing simulations. In this paper, the effects of the mold material and geometry on experimental measurements of bone cement setting temperature and setting time were evaluated by conducting the polymerization in different test molds. Finite element (FE) numerical simulations were also performed to provide a further understanding of these effects. It was found that the mold material and geometry significantly influence the values of the parameters measured using the ASTM standard. Results showed that the setting temperature measured was about 50 degrees C lower in a polytetrafluoroethylene (PTFE) mold than in a polyurethane (PU) foam mold for the 6 mm thickness cement. The measured peak temperature using PTFE molds varied about 75 degrees C for different mold heights (6mm vs. 40 mm), but only by 28 degrees C with PU molds. The measured setting time with PTFE molds varied by about 740 s for different mold heights (6 mm vs. 40 mm), while only by about 130 s for PU molds. Using PU foam materials for the test mold decreases cement heat transfer effects due to the poor heat conductivity of PU foam and provides more consistent measured results. FE parametric studies also support these observations. Poor conductivity materials, like PU foam, make better molds for the characterization of bone cement thermal behavior.     

"Conflicting" motion cues to the visual and vestibular self-motion systems around 0.06 Hz evoke simulator sickness

The basic question this research addressed was, how does simulator sickness vary with simulated motion frequency? Participants were 11 women and 19 men, 20 to 63 years of age. A visual self-motion frequency response curve was determined using a Chattecx posture platform with a VR4 head-mounted display (HMD) or a back-projected dome. That curve and one for vestibular self-motion specify a frequency range in which vestibular and visual motion stimuli could produce conflicting self-motion cues. Using a rotating chair and the HMD, a third experiment supported (p < .01) the hypothesis that conflicting cues at the frequency of maximum "crossover" between the curves (about 0.06 Hz) would be more likely to evoke simulator sickness than would conflicting cues at a higher frequency. Actual or potential applications of this work include a preliminary design guidance curve that indicates the frequency range of simulated motion that is likely to evoke simulator or virtual reality sickness; for simulators intended to operate in this frequency range, appropriate simulator sickness interventions should be considered during the design process.     

A temporal stability approach to position and attention-shift-invariant recognition

Incorporation of visual-related self-action signals can help neural networks learn invariance. We describe a method that can produce a network with invariance to changes in visual input caused by eye movements and covert attention shifts. Training of the network is controlled by signals associated with eye movements and covert attention shifting. A temporal perceptual stability constraint is used to drive the output of the network toward remaining constant across temporal sequences of saccadic motions and covert attention shifts. We use a four-layer neural network model to perform the position-invariant extraction of local features and temporal integration of invariant presentations of local features in a bottom-up structure. We present results on both simulated data and real images to demonstrate that our network can acquire both position and attention shift invariance.     

Disinformation: The Use of False Information

The distinction between misinformation and disinformation becomes especially important in political, editorial, and advertising contexts, where sources may make deliberate efforts to mislead, deceive, or confuse an audience in order to promote their personal, religious, or ideological objectives. The difference consists in having an agenda. It thus bears comparison with lying, because lies are assertions that are false, that are known to be false, and that are asserted with the intention to mislead, deceive, or confuse. One context in which disinformation abounds is the study of the death of JFK, which I know from more than a decade of personal research experience. Here I reflect on that experience and advance a preliminary theory of disinformation that is intended to stimulate thinking on this increasingly important subject. Five kinds of disinformation are distinguished and exemplified by real life cases I have encountered. It follows that the story you are about to read is true.     

A per-object-granularity tracking mechanism and systemfor interactive TV viewership estimation and program rating in real time

TV program ratings directly affect the decisions of advertisers and TV stations program offerings. TV program providers use television ratings reports to offer appropriate programs as well as attract advertisers. In this paper we propose a framework for TV audience estimates and program ratings using a per-object-granularity tracking mechanism for interactive TV content tracking in real time. It can be applied to live TV broadcasting environments as well as recorded broadcasting environments. The major components of the proposed tracking architecture are an interactive TV content creation tool powered by hotlinked video technology, a tracking information delivery framework with live interactive content insertion capability, an interactive TV content receiver, and tracking servers. The proposed mechanism and system in this paper enables a broadcast station or a rating agency to automatically perform tracking functions in real time based on viewer actions as well as on the content of audiovisual programming.