Effect of field enhancement on inorganic powder electroluminescence using short carbon nanotubes

Inorganic powder electroluminescence (IPEL) devices with the insertion of a carbon nanotube (CNT) layer were investigated to verify the effect of the increased local field produced by CNTs on electroluminescence (EL). To increase the field strength effectively, the CNTs were shortened using the cryogenic crushing method. IPEL devices with the insertion of a short CNT layer exhibited an increase in brightness and efficiency with increasing amount of CNTs. The local field enhancement by CNTs, further enlarged by the triple-junction, could increase the field strength applied to the phosphor, resulting in improved EL performance. In addition, short CNTs in an EL device can lead to field enhancement without an unintentional current flowing into the device.     

Comparative Analysis of Single‐Cascade Five‐Zone and Two‐Zone SMB Systems for the Separation of a Ternary Amino Acid Mixture

A ternary separation usually requires the use of two simulated moving bed (SMB) units in series. Since an increase in the number of SMB units leads to a significant increase in capital and operational costs, the use of a single SMB unit is preferred if its structure can be modified to treat a ternary separation. Such a modified single SMB unit has been typified by a five‐zone SMB or a two‐zone SMB so far. The separation performances‐of a five‐zone SMB and a two‐zone SMB are compared in this paper by using the ternary amino acid mixture as a model system. A five‐zone SMB is designed with the safety margin method while a two‐zone SMB is optimized using genetic algorithm. A five‐zone SMB based on the maximum allowable safety margin, although it may not guarantee the global optimum solution, results in much better separation performance than a two‐zone SMB at its global optimum state.     

The influence of filler on the emission properties and rheology of carbon nanotube paste

CNT paste consists of organic solution, inorganic binder and filler. Organic solution contains organic resins and solvent including surfactants which finely disperse CNTs. Filler affects surface morphology, electron emission property, viscosity, and rheological characteristics of CNT paste. We used different fillers such as silver and alumina in CNT paste for special function. The emission properties of CNT paste with silver are similar to those of CNT paste with alumina if filler portion is the same. From the scanning electron microscope (SEM) different morphologies of CNTs was observed depending on the type of filler. CNT paste which showed good emission property had vertically well-aligned CNTs on the surface after surface treatment using adhesive tape. We measured viscosity and rheological properties with rheometer RS600 from HAAKE. Emission property of CNT paste was evaluated in vacuum chamber of 10^{− 6} Torr with pulse generator and duty was 1/500.     

用于先进PCB制造工艺的叠层封装

在20世纪90年代,球栅阵列封装(BGA)和芯片尺寸封装(CSP)在封装材料和加工工艺方面达到了极限。这2种技术如同20世纪80年代的表面安装器件(SMD)和70年代通孔安装器件(THD)一样,在电学、机械、热性能、尺寸、质量和可靠性方面达到最大值。目前,三维封装正在成为用于未来采用的先进印制板(PCB)制造工艺的下一个阶段。它们可以分为圆片级封装、芯片级封装、和封装面。叠层封装(PoP)是一种封装面叠层封装类型的三维封装技术[15]。     

Photocatalytic hydrogen production over CuO and TiO2 nanoparticles mixture

Cheap and efficient photocatalysts were fabricated by simply mixing TiO₂ nanoparticles (NPs) and CuO NPs. The two NPs combined with each other to form TiO₂/CuO mixture in an aqueous solution due to the opposite surface charge. The TiO₂/CuO mixture exhibited photocatalytic hydrogen production rate of up to 8.23 mmol h⁻¹ g⁻¹ under Xe lamp irradiation when the weight ratio of P25 to CuO was optimized to 10. Although the conduction band edge position of CuO NPs is more positive than normal hydrogen electrode, the TiO₂/CuO mixture exhibited good photocatalytic hydrogen production performance because of the inter-particle charge transfer between the two NPs. The detailed mechanism of the photocatalytic hydrogen production is discussed. This mixing method does not require a complicated chemical process and allows mass production of the photocatalysts.     

Black silicon layer formation for application in solar cells

Low-cost, large area, random and mask less texturing scheme independent of crystal orientation are some of the factors that significantly influence the success of terrestrial photovoltaic technology. This work is focused on the texturing of the silicon surface microstructures by reactive ion etching using a multi-hollow cathode system. Desirable texturing effect has been achieved by applying a radio-frequency power of about 20 W per hollow cathode glow. The etched silicon surface shows almost zero reflectance in the visible region as well as in near-IR region. The silicon surface is covered by columnar microstructures with diameters ranging from 50 to 100 nm and with a depth of about 500 nm. Solar cells with efficiencies of 11.7% and 10.2% with black mono-crystalline and multi-crystalline silicon wafers, respectively, were successfully fabricated and tested.     

Early-warning performance monitoring system (EPMS) using the business information of a project

An early-warning performance monitoring system (EPMS) is proposed to objectively measure and monitor the performance of a project for early detection of inherent poor performance problems. The EPMS is built based on project progress data and consists of a database of business information, an optimized theoretical model used as a performance measurement baseline, and an index for monitoring and forecasting the performance. By monitoring the performance through an application of the EPMS to the Korean construction project, the quarterly variation of index was found to differ by project type. These results could explain the environmental changes in the project execution. Therefore, the EPMS is expected to be an alternative for objective performance monitoring and forecasting while applying the existing methods is difficult because of the limited available data on performance indicators. The development procedures may also be useful to researchers interested in approaches to quantitatively analyze trends in various industries.     

A web-based 3D ontology navigation system for spinal disease diagnosis

The Journal of Supercomputing - This paper presents a web-based three-dimensional (3D) navigation system for a spinal disease ontology using a 3D virtual human spine. The 3D navigation system...     

A continuous reverse skyline query processing scheme for multimedia data sharing in mobile environments

Multimedia Tools and Applications - Recently, various query processing schemes in mobile environments have been studied. Particularly, a reverse skyline query that is the variation of a skyline...     

The latent learning model to derive semantic relations of words from unstructured text data in social media

Multimedia Tools and Applications - Unstructured text data is very important in many applications because it reflects the thought of the people who create this data. However, it is difficult to...