High throughput optical readout of dense arrays of nanomechanical systems for sensing applications

We present an instrument based on the scanning of a laser beam and the measurement of the reflected beam deflection that enables the readout of arrays of nanomechanical systems without limitation in the geometry of the sample, with high sensitivity and a spatial resolution of few micrometers. The measurement of nanoscale deformations on surfaces of cm(2) is performed automatically, with minimal need of user intervention for optical alignment. To exploit the capability of the instrument for high throughput biological and chemical sensing, we have designed and fabricated a two-dimensional array of 128 cantilevers. As a proof of concept, we measure the nanometer-scale bending of the 128 cantilevers, previously coated with a thin gold layer, induced by the adsorption and self-assembly on the gold surface of several self-assembled monolayers. The instrument is able to provide the static and dynamic responses of cantilevers with subnanometer resolution and at a rate of up to ten cantilevers per second. The instrumentation and the fabricated chip enable applications for the analysis of complex biological systems and for artificial olfaction.     

Evaluating landslide deposits along the Tsurukawa fault zone, Japan, using magnetic susceptibility

 This paper describes the results of in-situ measurements of magnetic susceptibility in landslide deposits along the Tsurukawa fault zone in central Japan. The measured magnetic susceptibility values range from 0.4 to 9.6×10^–3 (in SI) and correspond to the proportions of the two component materials, weathered volcanic ash and faulted rock fragments. The study shows that landslide deposits along the Tsurukawa fault zone are composed of varying proportions of weathered volcanic ash. The results contrast with some general assumptions concerning landslides along fault zones in Japan. Received: 16 April 1999 · Accepted: 10 August 1999     

Effect of anisotropic scattering in neutronics analysis of BWR assembly

The anisotropic scattering effect to keff is studied for UO₂ and MOX fueled BWR assemblies. The anisotropic scattering effect increases the assembly k_∞ by 0.44% Δk for the UO₂ assembly with 0% void fraction, and by 0.21% Δk for the MOX assembly with 0% void fraction. This is because the anisotropic scattering effect flattens the intra-assembly thermal flux, and the absorption rate in the surrounding water gap is decreased, but the absorption rates in the MOX fuel rods are increased compared to the UO₂ rods. Therefore, the total decrease in absorption rates in the UO₂ assembly is relatively large, and the k_∞ is increased in the UO₂ assembly. The dependence of the anisotropic scattering effect on the void fraction is investigated, and the significant difference of 0.62% Δk/k is found for the 0% and the 80% void fractions. The BWR assemblies with Gd rods are also considered. Furthermore, the usefulness of the transport cross section is investigated, and it is found that the transport cross section gives reasonable anisotropic scattering effect, though not satisfactory.     

An optimization approach to establish an appropriate energy group structure for BWR pin-by-pin core analysis

An optimization approach to establish an appropriate multi-group energy structure for boiling water reactor (BWR) pin-by-pin fine mesh core analysis is proposed. In the present approach, the number of energy groups of cross sections is successively reduced or increased. In order to select an energy group boundary that is removed or added, performances of all possible candidates of energy group structures are tested in multi-assembly geometries. Then, the energy group boundary, which provides the minimum difference of the k-infinity or the pin-by-pin fission rate distribution, is finally removed or added. This procedure is repeated until the number of energy groups reaches to the target value. In order to confirm the applicability of the present approach, the accuracies of the k-infinity and the pin-by-pin fission rate distribution are investigated in various 2 × 2 multi-assembly geometries with the established energy group structure. From the verification results, the differences of the k-infinity and the pin-by-pin fission rate distribution between the reference (fine) and the established (coarse) energy group structure are small in the various 2 × 2 multi-assembly geometries. Therefore, we can conclude that the present approach is efficient to establish an appropriate energy group structure for BWR pin-by-pin fine mesh core analysis.     

A nationwide survey of NDMA in raw and drinking water in Japan

A nationwide survey of N-nitrosodimethylamine (NDMA) in both raw and finished water samples from drinking water treatment plants (DWTPs) in Japan was conducted. NDMA was analyzed by solid-phase extraction (SPE) followed by ultra performance liquid chromatography (UPLC) coupled with tandem mass spectrometry (MS/MS). NDMA was detected in 15 of 31 raw water samples collected in the summer at concentrations up to 2.6 ng/L, and in 9 of 28 raw water samples collected in winter at concentrations up to 4.3 ng/L. The NDMA concentrations were higher in raw water samples collected from treatment plants with catchment areas that have high population densities. The NDMA concentrations were higher in river water samples collected from the east and west of Japan than in those collected from other areas. NDMA was detected in 10 of 31 finished samples collected in summer at reduced concentrations of up to 2.2 ng/L, while 5 of 28 finished samples collected in winter showed NDMA concentrations up to 10 ng/L. The highest NDMA levels were detected in finished water samples collected from the Yodo River basin DWTP, which uses ozonation. Furthermore, evaluation of the process water produced at six advanced water treatment plants was conducted. Influent from the Yodo River indicated that the NDMA concentration increased during ozonation to as high as 20 ng/L, and then decreased with subsequent biological activated carbon treatment. To our knowledge, this is the first nationwide evaluation of NDMA concentrations in water conducted in Japan to date.     

Identification and C-terminal characterization of proteins from two-dimensional polyacrylamide gels by a combination of isotopic labeling and nanoelectrospray Fourier transform ion cyclotron resonance mass spectrometry

We propose a novel method for the identification and C-terminal characterization of proteins separated by two-dimensional polyacrylamide gel electrophoresis (2D-PAGE). Proteins were digested in a gel in a buffer solution containing 50% 18O-labeled water, and mixtures of 18O/16O-labeled peptides were analyzed by nanoelectrospray Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). This method was evaluated using horse skeletal muscle myoglobin as the model protein in SDS gel. The high resolution of FT-ICR MS minimized the overlapping of peptide peaks and facilitated identification of the C-terminal peptide, which was done by observing the undisrupted isotope peak pattern. As well, with its low ppm-level high mass accuracy, it can rapidly and reliably identify the in-gel-separated protein and determine its C-terminal by peptide mass fingerprinting alone. Therefore, this method should be applicable to routine and high-throughput proteome studies. Here, the method was applied to the analysis of rat liver proteins separated by 2D-PAGE. The C-termini of eight proteins were successfully identified out of 10 randomly picked Coomassie brilliant blue-stained spots. The feasibility and limitations of this approach are reported in this paper.     

Uniform characteristics with low threshold and high efficiency fora single-transverse-mode vertical-cavity surface-emitting laser-typedevice array

Vertical-to-surface transmission electrophotonic devices with a vertical-cavity are described. The individually accessed 12×4 arrays are characterized and demonstrated to have uniform room-temperature continuous-wave operating characteristics for a threshold current of ~2.8±0.15 mA and a slope efficiency of ~0.18±0.012 W/A with a single transverse mode. Both low threshold and high efficiency with 5% and 7% deviation, respectively, are achieved simultaneously. These devices can be used to constructing two-dimensional massively parallel optical interconnections     

Inhibition of angiotensin-converting enzyme increases the nitric oxide levels in canine ischemic myocardium

Since angiotensin-converting enzyme (ACE) produces angiotensin II in the heart, ACE inhibitors may prevent coronary vasoconstriction and increase coronary blood flow. On the other hand, since ACE inhibitors also inhibit kininase II which results in reduced degradation of bradykinin, ACE inhibitors may increase cardiac nitric oxide (NO) levels via stimulation of bradykinin receptors. This study was undertaken to test whether ACE inhibitors increase the cardiac NO levels and coronary blood flow in the ischemic myocardium. In 34 open-chest dogs, the left anterior descending coronary artery was perfused through an extracorporeal bypass tube from the left carotid artery. When either imidaprilat or cilazaprilat of 3 microg/kg/min was infused into the bypass tube for 10 min after reduction of coronary blood flow due to partial occlusion of the bypass tube, coronary blood flow increased from 31 +/- 1 to either 45 +/- 5 or 43 +/- 4 ml/100 g/min despite no changes in coronary perfusion pressure (43 +/- 2 mmHg). During an infusion of either imidaprilat or cilazaprilat, bradykinin and the end-products of NO (nitrate + nitrite) concentrations of coronary venous blood were markedly increased, which were attenuated by either HOE-140 (an inhibitor of bradykinin receptors) or by N(omega)-nitro-L-arginine methyl ester (an inhibitor of NO synthase). We also observed increases in cardiac bradykinin and NO levels due to either imidaprilat or cilazaprilat in the low constant coronary blood flow condition. It is concluded that ACE inhibitors can increase cardiac NO levels via the accumulation of bradykinin in the ischemic myocardium.     

Gastric cancer occurring in a patient with Plummer-Vinson syndrome: report of a case

We report herein the unusual case of a 59-year-old woman with Plummer-Vinson syndrome who developed gastric cancer. The patient had a longstanding history of dysphagia and iron deficiency anemia, for which she had sporadically taken iron supplements that improved the dysphagia to some extent, but not completely. Owing to her tolerance of the dysphagia, she had not been taking iron supplements for the past 17 years. On admission, she was in fair nutritional condition and not anemic. Blood chemistry results were all normal, including the serum iron level. Gastrointestinal radiographic series demonstrated cervical esophageal webs and advanced gastric cancer. Her dysphagia was successfully treated by endoscopic bougienage through the webs, and a distal partial gastrectomy with nodal dissection was performed. Histology of the resected stomach revealed atrophic mucosal change and, by chance, an adenomatous lesion in addition to adenocarcinoma. Her postoperative course was uneventful and she is now well, without any signs of recurrence. Although Plummer-Vinson syndrome is known to be associated with upper alimentary tract cancers, gastric cancer is extremely rare. A discussion on the etiology of Plummer-Vinson syndrome and its link with potential carcinogenesis follows this case report.