Reliable eye-diagram analysis of data links via device macromodels

This paper addresses the impact of device macromodels on the accuracy of signal integrity and performance predictions for critical digital interconnecting systems. It exploits nonlinear parametric models for both single-ended and differential devices, including the effects of power supply fluctuations and receiver bit detection. The analysis demonstrates that the use of well-designed macromodels dramatically speeds up the simulation as well it preserves timing accuracy even for long bit sequences.     

A spatiotemporal representation of the electromagnetic field radiated by short-pulse superwideband antennas

It is shown that two approaches can efficiently be applied to calculate impulse responses of antennas radiating superwideband signals. The simultaneous use of these approaches makes it possible to lucidly describe the operation of certain antennas and substantially simplify the calculations. The impulse responses of some short-video-pulse scanning array antennas and the shapes of radiated signals are calculated.     

PowerNap: an efficient power management scheme for mobile devices

We present PowerNap, an OS power management scheme, which can significantly improve the battery life of mobile devices. The key feature of PowerNap is the skipping of the periodic system timer ticks associated with the operating system. On an idle device, this modification increases the time between successive timer interrupts and enables us to put the processor/system into a more efficient low power state. This saves the energy consumed by workless timer interrupts and the excess energy consumed by the processor in less efficient low power states. PowerNap is tightly integrated with the kernel and is designed for optimal control of the latency and energy associated with transitioning in and out of the low power states. We describe an implementation of PowerNap and its impact on system software. Experiments with IBM's WatchPad verify the ability of PowerNap to extend battery life. An analytical model that quantifies the ability of the scheme to reduce power is also presented. The model is in good agreement with experimental results. We apply the model to small form-factor devices which use processors that have a PowerDown state. In such devices, PowerNap may extend battery life by more than 42 percent for small processor workloads and for background power levels below 10 mW.     

The method of double averaging: an approach for modeling power-factor-correction switching converters

This paper describes the modeling of power-factor-correction converters under average-current-mode control, which are widely used in switch-mode power supply applications. The objective is to identify stability boundaries in terms of major circuit parameters for facilitating design of such converters. The approach employs a double averaging procedure, which first applies the usual averaging over the switching period and subsequently applies generalized averaging over the mains period. The resulting model, after two averaging steps and application of a harmonic balance procedure, is nonlinear and capable of describing the low-frequency nonlinear dynamics of the system. The parameter ranges within which stable operation is guaranteed can be accurately and easily found using this model. Experimental measurements are provided for verification of the analytical results.     

Pre-Processing of Integral Images for 3-D Displays

This paper seeks to explore a method to accurately correct geometric distortions caused during the capture of three-dimensional (3-D) integral images. Such distortions are rotational and scaling errors which, if not corrected, will cause banding and moire effects on the replayed image. The method for calculating the angle of deviation in the 3-D Integral Images is based on Hough Transform. It allows detection of the angle necessary for correction of the rotational error. Experiments have been conducted on a number of 3-D integral image samples and it has been found that the proposed method produces results with accuracy of 0.05 deg     

Co-digestion of ruminal content and blood from slaughterhouse industries: influence of solid concentration and ammonium generation.

At the present time, organic solid wastes from industries and agricultural activities are considered to be promising substrates for biogas production via anaerobic digestion. Moreover solids stabilisation is required before reutilization or disposal. Slaughterhouses are among the most important industries in Uruguay and produce 150,000 tons of ruminal content (RC) and 30,000 tons of blood per year. In order to determine the influence of the solids and blood contents, the ammonia inhibition and the inoculum adaptation co-digestion batch tests were performed. A set of experiences with TS concentration of 2.5%, 5% and 7.5% and different ratios of RC/blood were carried out using an inoculum from an UASB reactor. In all experiences fast blood hydrolisation was observed. A higher methane production was detected in the experiences with higher TS content. However, the fraction of solids degradation was lower in these experiences. A plateau in the biogas production was found. The free ammonia level, which was above the reported inhibitory levels, could explain this behaviour. After the inhibition period the biogas production restarted probably due to the biomass acclimatisation to the ammonia. In order to determine the inoculum adaptation a new experiment was performed. The inoculum used was the sludge coming from the first set of experiences. Based upon batch tests a 3.5 m3 pilot reactor was designed and started up. Ammonia inhibition was avoided by the start-up strategy and in two weeks the biogas production was 3.5 m3/d. The VS stabilisation with a solid retention time of 20 days was of 43%. The pilot reactor working at steady state had a TS concentration of 3-4% with a ratio of RC/blood of 10:1 at the entrance.     

新安江电站进水口快速闸门动水闭门鉴定试验

本文叙述了应用现代科学方法和实验原型观测技术对新安江水电站进水口快速闸门进行安全检测鉴定，并介绍了水电站快速闸门动水闭门试验程序，对水电站快速闸门试验及相关鉴定有重要参考意义。     

Production of compounded asphalts of improved quality

Paving-and roofing-grade asphalts were obtained at LUKOIL-Permnefteorgsintez Ltd. by mixing peroxidized asphalt and a number of high-boiling unoxidized petroleum products in certain ratios. The asphalts obtained have improved performance characteristics: high plasticity and low brittleness temperature. __________ Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 2, pp. 26–28, May–June, 2006.     

CYLINDRICAL AND CONICAL FOLD GEOMETRIES IN THE CANTARELL STRUCTURE, SOUTHERN GULF OF MEXICO: IMPLICATIONS FOR HYDROCARBON EXPLORATION

The NW‐SE trending Cantarell structure in the Gulf of Campeche hosts the largest oilfield in Mexico. The oil occurs predominantly in latest Cretaceous – earliest Tertiary breccias with subsidiary reserves in Upper Jurassic (Oxfordian and Kimmeridgian) and Lower Cretaceous oolitic and partially dolomitized limestones, dolomites and shaly limestones. Cantarell has been interpreted both as a fold‐and‐thrust zone and as a dextral transpressional structure. Analysis of structure contours at 100m intervals, on the tops of the Tertiary breccia and the Kimmeridgian (Upper Jurassic) dolomite, indicates that the structure is an upright cylindrical fold with gently plunging conical terminations; there is also a conical portion in the central part of the structure. The axes of the central, NW and SE cones are subvertical. This geometry indicates that the two fold terminations and the central cone are aprons rather than points, with the NW and central cone axes intersecting the cylindrical fold axis at the point where the geometry switches from conical to cylindrical. The apical angle (i.e. the angle between the fold and cone axes) varies as follows: (i) in the NW cone, it is ～70° in the breccia and ～76° in the Kimmeridgian dolomite; (ii) in the central cone, it is ～77° in the breccia and ～73° in the Kimmeridgian dolomite; and (iii) in the SE cone, it is ～64° in the breccia and ～57° in the Kimmeridgian dolomite. This indicates that whereas the fold opens with depth in the NW cone, it tightens with depth in the central and SE cones. Assuming a parallel fold geometry, these apical angles indicate an increase in volume in the NW cone (i.e. larger hydrocarbon reservoirs), compared to the central and SE cones. Theoretical considerations indicate that the curvature increases dramatically towards the point of the cone. In the case of the Cantarell structure, the apices of the cones are located at the conical‐cylindrical fold junctions, where the highest curvature may have resulted in a higher degree of fracturing. The coincidence of maximum curvature and the intersection of the conical and cylindrical fold axes in the fold culminations with porous and permeable reservoir rocks may have made these locations favourable for the accumulation of hydrocarbons.     

Beneficial effects of wettability altering surfactants in oil-wet fractured reservoirs

In fractured reservoirs, an effective matrix-fracture mass transfer is required for oil recovery. Surfactants have long been considered for oil recovery enhancement, mainly in terms of their ability to reduce oil–water interfacial tension. These surfactants are effective when the fractured formations are water-wet, where capillary imbibition of surfactants from the fracture into the matrix contributes to oil recovery. However, another beneficial aspect of surfactants, namely their ability to alter wettability, remains to be explored and exploited. Surfactants capable of altering wettability can be especially beneficial in oil-wet fractured formations, where the surfactant in the fracture diffuses into the matrix and alters the wettability, enabling imbibition of even more surfactant into the matrix. This sequential process of initial diffusion followed by imbibition continues well into the matrix yielding significant enhancements in oil recovery.In order to test this hypothesis of sequential diffusion–imbibition phenomenon, Dual-Drop Dual-Crystal (DDDC) contact angle experiments have been conducted using fractured Yates dolomite reservoir fluids, two types of surfactants (nonionic and anionic) and dolomite rock substrates. A new experimental procedure was developed in which crude oil equilibrated with reservoir brine has been exposed to surfactant to simulate the matrix-fracture interactions in fractured reservoirs. This procedure enables the measurements of dynamic contact angles and oil–water interfacial tensions, in addition to providing the visual observations of the dynamic behavior of crude oil trapped in the rock matrix as it encounters the diffusing surfactant from the fractures. Both the measurements and visual observations indicate wettability alterations of the matrix surface from oil-wet to less oil-wet or intermediate wet by the surfactants. Thus this study is of practical importance to oil-wet fractured formations where surfactant-induced wettability alterations can result in significant oil recovery enhancements. In addition, this study has also identified the need to include contact angle term in the dimensionless Bond number formulations for better quantitative interpretation of rock–fluids interactions.