Thermo-optic design for microwave and millimeter-wave electromagnetic power microsensors

Rendina et al. recently proposed the original configuration of an electromagnetic power sensor for microwaves and millimeter waves that is based on an optically interrogated all-silicon chip [Electron. Lett. 35, 1748 (1999)]. Here we theoretically analyze and discuss in detail the performances of such a new class of nonperturbing and wideband probe in terms of sensitivity, resolution, intrinsic detectivity, linearity, and response time. Good agreement between theory and experiments is demonstrated. In particular, minimum resolutions of approximately 1 mW/cm2 are obtained at frequencies beyond 10 GHz. The dependence of response on the geometrical and electromagnetic parameters of the sensing element is analyzed, and on this basis the possibility of achieving optimized configurations is discussed.     

A Scalable Architecture for MPEG-4 Wavelet Quantization

Wavelet-based image compression has been adopted in MPEG-4 for visual texture coding. All wavelet quantization schemes in MPEG-4—Single Quantization (SQ), Multiple Quantization (MQ) and Bi-level Quantization—use Embedded Zero Tree (EZT) coding followed by an adaptive arithmetic coder for the compression and quantization of a wavelet image. This paper presents the OZONE chip, a dedicated hardware coprocessor for EZT and arithmetic coding. Realized in a 0.5 m CMOS technology and operating at 32 MHz, the EZT coder is capable of processing up to 25.6 Mega pixel-bitplanes per second. This is equivalent to the lossless compression of 31.6 8-bit grayscale CIF images (352 × 288) per second. The adaptive arithmetic coder processes up to 10 Mbit per second. The combination of the performance of the EZT coder and the arithmetic coder allows the OZONE to perform visual-lossless compression of more than 30 CIF images per second. Due to its novel and scalable architecture, parallel operation of multiple OZONEs is supported. The OZONE functionality is demonstrated on a PC-based compression system.     

On the rates of convergence of the finite element method

The rate of convergence of the finite element method is a function of the strategy by which the number of degrees-of-freedom are increased. Alternative stragegies are examined in the light of recent theoretical results and computational experience.     

Integrated ambient ozone evaluation by passive samplers and clover biomonitoring mini-stations

An ozone monitoring network was set up using passive samplers and biological mini-stations of two clones of white clover (Trifolium repens L. cv. Regal), NC-R (O(3)-resistant) and NC-S (O(3)-sensitive). This paper reports on a pilot study performed in the period June-October 1999 in the Rome municipal area by using five biomonitoring mini-stations and ozone passive samplers with a new nitrite based design. This combined methodology can be used to obtain information on the biological implications of the injury due to tropospheric ozone. The two techniques can integrate data for the short-medium period and can be placed in different urban and rural sites, proving to be a very useful tool for ozone concentration mapping.     

Computer-controlled mechanical simulation of the artificially ventilated human respiratory system

A mechanical lung simulator can be used to simulate specific lung pathologies, to test lung-function equipment, and in instruction. A new approach to mechanical simulation of lung behavior is introduced that uses a computer-controlled active mechatronic system. The main advantage of this approach is that the static and dynamic properties of the simulator can easily be adjusted via the control software. A nonlinear single-compartment mathematical model of the artificially ventilated respiratory system has been derived and incorporated into the simulator control system. This model can capture both the static and dynamic compliance of the respiratory system as well as nonlinear flow-resistance properties. Parameters in this model can be estimated by using data from artificially ventilated patients. It is shown that the simulation model fits patient data well. This mathematical model of the respiratory system was then matched to a model of the available physical equipment (the simulator, actuators, and the interface electronics) in order to obtain the desired lung behavior. A significant time delay in the piston motion control loop has been identified, which can potentially cause oscillations or even instability for high compliance values. Therefore, a feedback controller based on the Smith-predictor scheme was developed to control the piston motion. The control system, implemented on a personal computer, also includes a user-friendly interface to allow easy parameter setting.     

A new removable resist for high aspect ratio applications

A variety of different photo resists are used for fabrication of MEMS. Presently good results were reported for SU-8, a chemically amplified negative tone photoresist. But SU-8 has a disadvantage for some applications in LIGA technique, especially in the X-ray mask fabrication. After processing the finished resist pattern are hardly soluble from the substrate. This paper will briefly describe the current status of the development of the new negative tone photoresist CAR 44 whose big advantage is the easy removableness of the cross linked pattern. This work widely uses the contents of the presentation “A New Removable Resist for High Aspect Ratio Applications” to the High Aspect Ratio Micro Structure Technology workshop HARMST 2005 held in Gyeongyu (Republic of Korea), June 10–13, 2005.     

Assessment of the cost and accuracy of the generalized FEM

In this paper, we address the cost versus accuracy capabilities for the generalized FEM (GFEM) which was developed in (Comput. Methods Appl. Mech. Eng. 2003; 192 :3109–3161, Int. J. Numer. Meth. Engng 2004; 60 :1639–1672, Ph.D. Thesis, Texas A&M University, College Station, TX, August 2003 (Advisor: T. Strouboulis)), and also the construction of two‐sided a posteriori error estimates, which can be used to assess the achieved accuracy at all levels of the method. Copyright © 2006 John Wiley & Sons, Ltd.     

Microwave dewaxing applied to the investment casting process

Autoclave processing is commonly used nowadays for dewaxing in the investment casting process. However, since the use of microwave is steadily growing in industrial processes and the wax interacts with the electromagnetic energy of the microwaves, the present work studies the possibility of carrying out dewaxing via microwave. The wax (mineral wax, vegetable resin, low molecular-weight polymer and anti-oxidant) used in this work was prepared by melting in an oven equipped with a mineral oil bath. The chemical and structural stability of the wax were monitored throughout 12 simulated dewaxing cycles, via various analyses, namely, volumetric expansion, hardness, Fourier transform infrared spectroscopy, ultraviolet–visible spectrophotometry, differential scanning calorimetry and viscosity. The results showed that microwave dewaxing is viable, significantly decreasing the incorporation of dirt and water, which is inevitable in the autoclave dewaxing process.