Biodegradability Study of the Biosurfactant Contained in a Crude Extract from Corn Steep Water

Over the last few years, the global biosurfactant market has raised due to the increasing awareness among consumers, for the use of biological or bio-based products. Because of their composition, it can be speculated that these are more biocompatible and more biodegradable than their chemical homologous. However, at the moment, no studies exist in the literature about the biodegradability of biosurfactants. In this work, a biosurfactant contained in a crude extract, obtained from a corn wet-milling industry stream that ferments spontaneously in the presence of lactic acid bacteria, was subjected to a biodegradation study, without addition of external microbial biomass, under different conditions of temperature (5–45 °C), biodegradation time (15–55 days), and pH (5–7). For that, a Box–Behnken factorial design was applied, which allowed to predict the percentage of biodegradation for the biosurfactant contained in the crude extract, between the range of the independent variables selected in the study, obtaining biodegradation values between 3 and 80%. The percentage of biodegradation for the biosurfactant was calculated based on the increase in the surface tension of samples of the crude extract. Furthermore, it was also possible to predict the variation in t_1/2 for the biosurfactant (time to achieve the 50% of biodegradation) under different conditions.     

Separation of hematite from banded hematite jasper (BHJ) by magnetic coating

The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that besides hematite and goethite,jasper, a microcrystalline form of quartzite, is the major impurity associated with this ore. Beneficiation by conventional magnetic separation technique could yield a magnetic concentrate containing 60.8% Fe with 51% Fe recovery. In order to enhance the recovery of the iron oxide minerals, fine magnetite, colloidal magnetite and oleate colloidal magnetite were used as the coating material. When subjected to magnetic separation, the coated ore produces an iron concentrate containing 60.2% Fe with an enhanced recovery of56%. The AFM studies indicate that the coagulation of hematite particles with the oleate colloidal magnetite facilitates the higher recovery of iron particles from the low grade BHJ iron ore under appropriate conditions.     

Quantitative UPLC‐MS/MS analysis of chlorogenic acid derivatives in antioxidant fractionates from dandelion (Taraxacum officinale) root

While qualitative studies have identified chlorogenic acids in antioxidant extracts, particularly ethyl acetate‐derived extracts, of Taraxacum officinale, quantitative analysis of these phenolic compounds remains largely unreported for this species. In this study, bioactivity‐guided fractionation of an antioxidant crude ethyl acetate extract (DPPH = 295.481 ± 0.955 mg TE g^?1 extract) from T. officinale root resulted in a number of reverse‐phase fractions that demonstrated high antioxidant activity (DPPH = 1058.733–1312.136 mg TE g^?1 extract), stronger than that of the synthetic antioxidant Trolox^®. UPLC‐MS/MS screening of these fractions for the presence of selected mono‐ and di‐caffeoylquinic acids revealed large quantities of 1,5‐dicaffeoylquinic acid present in several fractions (853.052–907.324 μg mg^?1), respectively. Due to the antioxidant potency and high levels of 1,5‐dicaffeoylquinic acid observed in these fractions, it was concluded that specifically this chlorogenic acid derivative is a major contributor to the antioxidant efficacy of dandelion root.     

A Stimulation Method to Assess the Contractile Status of the Lumbar Extensors in a Seated Posture

The purpose of present study was to develop and evaluate methods to assess stimulation responses of the lumbar extensors, as part of a longer‐term goal of detecting fatigue during prolonged sitting. Three stimulation frequencies (2, 5, and 8 Hz) were tested in separate stages, which include 3 stimulation trains and 4 sampling blocks. Repeated measures analyses of variance were used to determine whether any significant differences in mean stimulation responses occurred with respect to stimulation frequency, sampling block, and stimulation train. Reliability of measured stimulation responses was assessed within and between sampling blocks using intraclass correlation coefficients. Stimulation frequencies significantly affected the stimulation responses and time‐to‐potentiation differed between the 3 stimulation frequencies; it was highest for 2 Hz stimulation. All 3 stimulation frequencies resulted in excellent reliability within and between sampling blocks. Use of the current protocol at 2 Hz is recommended as appropriate to measure the lumbar extensors status during prolonged sitting.     

Ga-doped IZO films obtained by magnetron sputtering as transparent conductors for visible and solar applications

C-axis textured thin films of gallium-doped indium zinc oxide (GIZO) with a 2% ratio of Ga/Zn, were obtained via RF-magnetron sputtering with high transparency and electrical conductivity. A Box-Behnken response surface design was used to evaluate the effects of the deposition parameters (In₂O₃ target power, deposition time, and substrate temperature) on the chemical composition, optical, electrical, and structural properties of the GIZO films. The optical constants and the electrical properties were obtained using optical models. The GIZO stoichiometry, and therefore the In/Zn atomic ratio, affected the crystallinity, crystalline parameters, band gap, and charge carrier mobility of the GIZO films. The charge carrier density was related to the change in the crystalline parameters of the hexagonal structure and the In/Zn atomic ratio. The best electrical conductivity values (1.75?×?10³ Ω^?1 cm^?1) were obtained for GIZO films with In/Zn ratio ≥?1. Several figures of merit (FOM) defined for the visible and solar regions were comparatively used to select the optimal In/Zn atomic ratio that provided the best balance between the conductivity and the transparency. The optimal In/Zn ratio was in a range of 0.85–0.90 for the GIZO films.     

Design guidelines for titania-silica-alumina ceramics with tuned anatase to rutile transformation

Titania-based ceramics with adjustable anatase-rutile fractions were obtained by milling of anatase, quartz and corundum precursors, uniaxial pressing and firing at 1100?°C. The influence of silica and alumina, combined with milling time and compaction pressure, was studied by design of experiments. The L9 orthogonal array with a three-level noise factor was employed. Firing of pure titania at 1100?°C yielded complete anatase to rutile transformation (ART), whereas stabilized samples show that an optimum amount of 9% silica and 33% alumina reduces phase transformation to only about 5?wt% rutile. An extended correlation matrix combined with analysis of variance (ANOVA) was applied to assess the combined effects of quartz, alumina, milling time and uniaxial compressing pressure on relative density, and anatase to rutile transformation. Results show absence of ART after milling, and controlled partial conversion of anatase to rutile after firing. Very good fitting was obtained by multivariate analysis on considering first and second order terms for dependence on silica contents and interactions between silica and each of the remaining factors, including milling time. This empirical dependence could be interpreted on a sound physicochemical basis, allowing the prediction of suitable compositions and processing conditions to obtain rutile-free samples by conventional ceramic processing, and to design ceramic samples with controlled fractions of anatase and rutile.     

Investigation on external stimuli engendered magnetic ordering in polycrystalline CaCu3Ti4O12 quadruple perovskite

The consequences of high energy mechanical milling, microwave-assisted heating and rapid thermal cooling on magnetic ordering in polycrystalline CaCu₃Ti₄O₁₂ cubic perovskite have been investigated by means of X-ray powder diffractometry (300?K), dc magnetization in field – cooled and zero – field cooled modes (H = 100?Oe and 1000?Oe, T?=?5–300?K) (M – T curves) and M – H loop characteristics (T?=?5?K and 300?K, H_max = 70?kOe). The M – T curves of unmilled and 16?h milled samples show pure antiferromagnetic and weak ferromagnetic ordering, respectively, 1?h and 6?h milled samples demonstrate the coexistence of both the phases while microwave-assisted and quenched samples exhibit classic antiferromagnetic transition and a low temperature paramagnetic–like contribution with different weights, well supported by the M – H loop characteristics. The observed transformations in the magnetic ordering are attributed to the ball-milling induced stress which curtails hybridization of empty Ti-3d orbitals with Cu-3d and O-2p orbitals and secondary phase formation. Oxygen vacancies associated with bound magnetic polarons originate ferromagnetism in the milled samples while unpaired electrons inhabited at the empty sites are the cause of paramagnetic centers. The low-temperature Curie – tail in M – T curve for quenched and microwave assisted samples is attributed to Ti³⁺ cations.