Analytical evaluation technique of self-phase-modulation effect onthe performance of cascaded optical amplifier systems

We propose an approximate analytical evaluation technique of self-phase-modulation (SPM) in cascaded optical amplifier systems. The effect of SPM on optical pulse distortion is represented by the increase in the α-parameter of the transmitter. The waveform distortion is approximated by assuming that the pulse is transmitted over a dispersive fiber without nonlinearity. This technique greatly reduces the calculation time, and is especially useful in designing cascaded amplifier systems, evaluating theoretical maximum transmission distance     

Transmission distance of in-line amplifier systems withgroup-velocity-dispersion compensation

Group-velocity dispersion (GVD) compensation in in-line amplifier systems is evaluated from the viewpoint of improving the transmission distance. The nonlinear Schrodinger equation, which simulates signal propagation in optical fibers, is numerically evaluated to clarify the optimum configuration for GVD compensation. It is shown that the optimum amount of GVD compensation is about 100% of the GVD experienced by the transmitted signal. The optimum compensation interval is found to be a function of the bit rate, signal power, and dispersion parameter. For dispersion parameter values ranging from about -0.1 ps/nm/km to -10 ps/nm/km, and an amplifier noise figure of about 6 dB, the optimum compensation configuration can eliminate the GVD from in-line amplifier systems, thus improving transmission distances to those limited by self-phase modulation and higher-order GVD     

Integrated-optic double-ring resonators with a wide free spectralrange of 100 GHz

Integrated-optic double-ring resonators with a wide free spectral range (FSR) of 100 GHz are fabricated using GeO₂-doped silica waveguides with a high relative refractive index difference (Δ) of 1.5%. The resonators are composed of two ring resonators comprising small ring waveguides with radii of 1.75 and 2.0 mm. The double-ring resonator module exhibited a wide FSR of 98.0 GHz, a finesse of higher than 138, a low crosstalk of less than -11.7 dB, and a low insertion loss of 6.1 dB. The measured FSR of 98.0 GHz is wider than any previously reported ring resonator composed of optical waveguides     

Pyrolysis of tertiarybutylphosphine at low pressure

The pyrolysis of tertiarybutylphosphine (TBP) has been studied in the low pressure conditions used for chemical beam epitaxy (CBE). The pyrolysis studies were carried out in low pressure reactors of two different configurations, one of which is a cracker cell designed for use in a CBE system. The reaction products were studied using a quadrupole mass spectrometer. The products observed are accounted for by a reaction mechanism involving homolysis of the parent TBP molecule to produce PH₂ and C₄H₉ radicals. These undergo subsequent reactions to form the stable products C₄H₈, PH₃ and H₂, with smaller amounts of P and P₂ being produced. The production of the sub-hydride PH₂ using this cracker cell design indicates that the use of partially cracked TBP may be a promising technique for reducing the amount of carbon incorporated into the growing epitaxial layer.     

Speed control of a PV powered DC motor driving a self-excited3-phase induction generator for maximum utilization efficiency

Photovoltaic (PV) powered DC motors driving dedicated loads (e.g. water pumps) are increasingly used in the remote rural areas of many developing countries. The key to their success is simplicity (direct coupling, no DC-AC conversion, no storage batteries, etc.). Because of the relatively high cost of the PV array, the system designer is interested in maximizing its utilization efficiency. A PV powered DC motor can also be used to drive a three-phase self-excited induction generator (SEIG). This arrangement is useful as part of an integrated renewable energy system (IRES), which takes advantage of the inherent diversity of wind and solar energy in most developing countries to improve power quality. The SEIG is driven by a wind-turbine, DC motor, or both. Another advantage of this arrangement is its versatile control characteristics through the DC motor control. This paper describes a technique to maximize the utilization efficiency of the PV array by controlling the field current of the DC motor through a DC chopper     

Sensitivity of torsional stress predictions of diesel generatorsets to critical parameter values

In the present paper a new method is presented for the evaluation of torsional stressing of diesel-generator sets consisting of components with uncertain torsional characteristics. A frequency scanning technique is implemented for eigenvalue analysis of the elastic system. Due to the uncertainty of the values of stiffness and damping coefficients, a sensitivity analysis method is also presented, suitable for the evaluation of the range of the mechanical stresses. Special consideration is given to the correct simulation of the coupling to the electric network, including the influence of generator regulators and possible network interactions. An exact formula is extracted for the synchronizing and damping torque coefficients. The method presented was checked in a diesel power station of the autonomous electric system of a Greek island     

Trade-off between resolution and interactivity in spatial taskperformance

Virtual reality displays usually lag far behind classical computer graphics displays in static image quality parameters, such as resolution. Both the popular press and scientific papers often stress that resolution will have to increase greatly before users can experience virtual environments as “the real thing”. Nevertheless, it is already possible to do some useful work in VR environments. The point we experimentally demonstrate here is that resolution is much less important for interactive tasks that employ immersive VR, where users can explore the environment by moving their heads and bodies, than it is in classical computer graphics applications, where users can only explore by gazing at a single picture. In the context of unmanned aerial vehicles, frame rate (read: passive camera movement) is more important than resolution for target detection, recognition, designation, and tracking. In the experiments reported here, we investigated the relative importance of various image parameters like spatial resolution (number of pixels per video frame), intensity resolution (number of gray levels per pixel), and temporal resolution (number of frame updates per second). Most experimental data concerning these resolutions come from classical psychophysics. However, experimental conditions in classical psychophysics feature stationary observers looking at short-term, pointlike flashes on stationary displays, and are thus far more representative of human interaction with pictures and photographs than with highly interactive systems like those employed in virtual reality     

Oblique flow impinging on a wall with suction or blowing

Summary The oblique flow of a viscous fluid impinging on a flat wall with suction or blowing is studied. It is found that when suction is applied the fluid penetrates the wall while blowing causes the shifting of the stagnation point. It is also found that this shifting depends upon the magnitude of the blowing.     

Optimization of a Reconstitutable Suspension of Rifampicin Using 24 Factorial Design

In this study 2⁴ factorial design associated with surface response methodology was used to develop and optimize a reconstitutable suspension of rifampicin. The study illustrated the effect of the percentage of each of sucrose, avicel RC-591, hydrophilic aerosil, and aerosol-OT on the flowability and the bulk density of the dry mixture as well as the viscosity, the sedimentation volume, and the redispersibility of the suspension. An empirical equation developed for each of the above responses was used with the aid of computer software to plot a contour map of the most significant effects and interactions. Five replicates at the center of the design were used to independently calculate the experimental error and to detect any curvature in the response surface. Three formulas which are not included in the design were prepared to check the validity of the model equation.