Low-power CSD linear phase FIR filter structure using verticalcommon sub-expression

A high-speed/low-power canonic signed digit (CSD) linear phase finite impulse response (FIR) filter structure using vertical common sub-expression is proposed. In the conventional linear phase CSD filter, the horizontal common sub-expression method (see Hartley, 1996) has been widely utilised due to the inherent symmetrical filter coefficients. However, use has been made of the fact that the most significant bits of adjacent filter coefficients in the linear phase filter are also equal since they have mostly similar values. Through the example, it is shown that the proposed structure is more efficient in the case where bit precision of implementation is lower     

Selective and nonselective wet etching of Zn0.9Mg0.1O/ZnO

Wet etch rates at 25°C for Zn_0.9Mg_0.1O grown on sapphire substrates by pulsed laser deposition (PLD) were in the range 300–1100 nm · min⁻¹ with HCl/H₂O (5×10⁻³−2×10⁻² M) and 120–300 nm · min⁻¹ with H₃PO₄/H₂O (5×10⁻³−2×10⁻² M). Both of these dilute mixtures exhibited diffusion-limited etching, with thermal activation energies of 2–3 kCal · mol⁻¹. By sharp contrast, the etch rates for ZnO also grown on sapphire by PLD were much slower in similar solutions, with rates of 1.2–50 nm · min⁻¹ in HCl/H₂O (0.01–1.2 M) and 12–54 nm · min⁻¹ in H₃PO₄/H₂O (0.02–0.15 M). The etching was reaction limited over the temperature range 25–75°C, with activation energies close to 6 kCal · mol⁻¹. The resulting selectivity of Zn_0.9Mg_0.1O over ZnO can be a high as ∼400 with HCl and ∼30 with H₃PO₄.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

Error Concealment Based on Semantic Prioritization with Hardware‐Based Face Tracking

With video compression standards such as MPEG‐4, a transmission error happens in a video‐packet basis, rather than in a macroblock basis. In this context, we propose a semantic error prioritization method that determines the size of a video packet based on the importance of its contents. A video packet length is made to be short for an important area such as a facial area in order to reduce the possibility of error accumulation. To facilitate the semantic error prioritization, an efficient hardware algorithm for face tracking is proposed. The increase of hardware complexity is minimal because a motion estimation engine is efficiently re‐used for face tracking. Experimental results demonstrate that the facial area is well protected with the proposed scheme.     

Structural properties of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 relaxor ferroelectric thin films on SrRuO3 conducting oxides

Coating of 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) relaxor ferroelectrics by a sol–gel method is followed by growth of epitaxial SrRuO₃ (SRO) metallic oxide electrodes on SrTiO₃ (STO) single-crystal substrate by pulsed laser deposition. High-quality PMN–PT films on SRO with preferred growth orientation were successfully fabricated by controlling the operation parameters. Structural properties of relaxor ferroelectric PMN–PT thin films on SRO/STO substrates have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). In-plane and out-of-plane alignments of the heterostructure are confirmed and the structural twinning of the materials are also revealed.     

Microstructural investigation of long-term degradation mechanisms in GFRP dowel bars for jointed concrete pavement

Steel dowel bar is used to transfer loads in concrete pavement slab. However, once the steel dowel bar corrodes, it may cause faults, such as joint freezing in concrete pavement, level differences resulting from spalling or decreased efficiency of load transfer, etc., which are the same problems experienced by typical reinforcing steel. This study evaluated the applicability of glass fiber-reinforced polymer (GFRP) dowel bar as a substitute for steel dowel bar. A microstructural analysis was conducted to examine the decrease in durability of GFRP dowel bar exposed to deterioration environments. To analyze the deterioration mechanism of GFRP dowel bar, scanning electron microscopy was employed and the porosity was measured by the gas absorption method. It was concluded that the longer the GFRP dowel bar was exposed to deterioration environments, the more the interlaminar shear stress decreased. This result was validated by the microstructural analysis. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of changes in strain path on the anisotropy of yield stresses of low-carbon steel and 70-30 brass sheets

Uniaxial tensile tests in various directions following uniaxial extension, equibiaxial stretching or plane strain rolling have been performed to study the effects of changes in strain path on the anisotropy of yield stresses of aluminium-killed low-carbon steel and 70-30 brass sheets. The anisotropy could be predicted from the specimen textures, if dislocation structure were equiaxed, as in the case of equibiaxial stretching. However, elongated dislocation cell structures, developed in the steel specimens prestrained in uniaxial tension or plane strain rolling, gave rise to the second-stage yield stresses higher than predicted from textures in the directions different from the maximum prestrain direction. Planar dislocation structures in the brass specimens prestrained in uniaxial tension or plane strain rolling gave the second-stage yield stresses lower than predicted from the textures in the directions different from the maximum prestrain direction. The phenomena are discussed based on textures and dislocation structures.     

Development of a physics analysis procedure for the prismatic very high temperature gas-cooled reactors

A new physics analysis procedure has been developed for a prismatic very high temperature gas-cooled reactor based on a conventional two-step procedure for the PWR physics analysis. The HELIOS and MASTER codes were employed to generate the coarse group cross sections through a transport lattice calculation, and to perform the 3-dimensional core physics analysis by a nodal diffusion calculation, respectively. Physics analysis of the prismatic VHTRs involves particular modeling issues such as a double heterogeneity of the coated fuel particles, a neutron streaming in the coolant channels, a strong core-reflector interaction, and large spectrum shifts due to changes of the surrounding environment and state parameters. Double heterogeneity effect was considered by using a recently developed reactivity-equivalent physical transformation method. Neutron streaming effect was quantified through 3-dimensional Monte Carlo transport calculations by using the MCNP code. Strong core-reflector interaction could be handled by applying an equivalence theory to the generation of the reflector cross sections. The effects of a spectrum shift could be covered by optimizing the coarse energy group structure. A two-step analysis procedure was established for the prismatic VHTR physics analysis by combining all the methodologies described above. The applicability of our code system was tested against core benchmark problems. The results of these benchmark tests show that our code system is very accurate and practical for a prismatic VHTR physics analysis.