Microwave Dielectric Properties of CaTiO3-Ca(Al1/2Ta1/2)O3 Ceramics

The microwave dielectric properties of CaTi_1-χ(Al_1/2Ta_1/2)_cHO₃ solid solutions (0.3 ≤χ≤ 0.5) have been investigated. The ceramic samples had perovskite structures similar to CaTiO₃. The partial substitution of Ti₄₊ by a coupled Al₃₊/Ta_s+ permitted improvement of the quality factor Q . The dielectric constant (τ_r) and temperature coefficient of resonant frequency (τ_r) decrease rapidly with an increase of χ. A new high-quality microwave dielectric material was found at χ= 0.46 with σ_r= 46.5, Q f = 27300 GHz, and π_f= 0 ppm/°C. The relationship between microstructures and dielectric properties is presented.     

Kinetics of volume expansion during infusion of Ringer’s solution based on two volume model

In this work mathematical models were developed to represent the kinetics of volume changes of fluid spaces associated with infusion of Ringer’s solution. During infusion of Ringer’s solution, the human body is assumed to be characterized by the two-fluid space model which has second volume space in addition to the first volume so that fluid exchanges between these two spaces are possible. Various infusion types were tested to accommodate different medical situations. Volunteers were given Ringer’s solution and the changes in blood hemoglobin were detected. From the comparison with experimental data, the two-fluid space model was found to represent adequately the kinetics of human volume expansion during infusion of Ringer’s solution.     

Surface crosslinking of high‐density polyethylene beads in a modified plasma reactor

High‐density polyethylene (HDPE) beads were successfully surface‐crosslinked in a modified plasma reactor. The modified plasma reactor treats large amounts of beads, which are uniformly surface‐crosslinked. In this study, effects of the gas pressure, radio‐frequency (RF) power, and the treatment time on the degree of surface crosslinking were systematically investigated. Degree of surface crosslinking was measured by solvent extraction method (boiling xylene method, BXM). The gel content of plasma‐treated HDPE increases from 0.0 to 1.05% within 10 min at 100 mTorr, 200 W. FTIR and DSC analyses show that the crosslinked layer after plasma treatment is limited only at HDPE surface without changing the bulk thermal property of HDPE. Through the analysis of FTIR, it was confirmed that main peaks corresponding to CH₂ bands were decreased and two peaks corresponding to CF₂ and CF₃ were observed after plasma surface modification. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2921–2929, 2002; DOI 10.1002/app.10295     

Structure development in biaxially stretched polystyrene film: Part II. Theoretical analysis of orientation development

The present paper describes an analysis of the orientation developed in biaxially stretched polystyrene films in terms of the kinematics of the process and a viscoelastic constitutive equation. It was possible to achieve reasonable agreement of predicted and experimental birefringences through use of a convected Maxwell model and the Rheo-Optical Law.     

Polydispersity effect on transient flow behavior of polystyrene solution

Summary The transient flow behavior of the binary blend of monodisperse polystyrene fractions is measured by a flow birefringence method. Both of the shear stress and first normal stress difference are obtained simultaneously in time by using a PMFB technique. The entanglements of the polymer chains significantly affect the rheological property of the binary blend in flow region. Especially, the entanglements of the high molecular weight fractions with themselves is proven to be the main source to the growth of first normal stress differences.     

Dynamics of the wet-end section in paper mills

A model representing the wet-end section of a paper mill has been developed to characterize its dynamic behavior during the grade change. The model is based on the mass balance relationships written for the simplified wetend white water network. From the linearization of the dynamic model, higher-order Laplace transfer functions were obtained followed by the reduction procedure to give simple lower-order models in the form of 1^st-order or 2^nd-order plus dead times. The dynamic response of the wet-end is influenced both by the white water volume and by the level of wire retention. Effects of key manipulated variables such as the thick stock flow rate, the ash flow rate and the retention aid flow rate on the major controlled variables were analyzed by numerical simulations. The simple dynamic model developed in the present study can be effectively used in the operation and control. This paper is dedicated to Professor Se Ki Moon on the occasion of his retirement from Hanyang University.     

Preparation of ketoprofen‐loaded high‐molecular‐weight poly(vinyl alcohol) gels

High‐molecular‐weight atactic poly(vinyl alcohol) (a‐PVA) gels loaded with (R,S)‐2‐(3‐benzoylphenyl)propionic acid (ketoprofen) were prepared from 5, 6, 7, and 8 g/dL solutions of a‐PVA with a number‐average degree of polymerization of 4000 in an ethylene glycol/water mixture with an aging method to identify the effect of the initial polymer concentration on the swelling behavior, morphology, and thermal properties of a‐PVA gels. Then, the release behavior of ketoprofen from a‐PVA gels was investigated. As the polymer concentration decreased, the ability for network formation decreased, and the degree of swelling of the a‐PVA gels increased. In addition, the enthalpy increased with an increase in the a‐PVA concentration, but the melting temperatures of the gels prepared at different initial polymer concentrations were the same; this indicated that tighter gel networks would be formed by a higher polymer chain density. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Selective Oxidation of Methanol to Formaldehyde Using Modified Iron-Molybdate Catalysts

Methanol selective oxidation to formaldehyde over a modified Fe-Mo catalyst with two different stoichiometric (Mo/Fe atomic ratio = 1.5 and 3.0) was studied experimentally in a fixed bed reactor over a wide range of reaction conditions. The physicochemical characterization of the prepared catalysts provides evidence that Fe₂(MoO₄)₃ is in fact the active phase of the catalyst. The experimental results of conversion of methanol and selectivity towards formaldehyde for various residence times were studied. The results showed that as the residence time increases the yield of formaldehyde decreases. Selectivity of formaldehyde decreases with increase in residence time. This result is attributable to subsequent oxidation of formaldehyde to carbon monoxide due to longer residence time.     

Dispersant-free dyeing of polyester with temporarily solubilised azo disperse dyes from 1-substituted-2-hydroxypyrid-6-one derivatives

Four temporarily solubilised azo disperse dyes based on 1-substituted-2-hydroxypyrid-6-one were synthesised and characterised. The dyes showed high extinction coefficients and had a yellow shade on polyester fabric. They were successfully applied to polyester without the use of dispersants and the optimum pH was found to be 5. It was found that the dyes could be alkali-cleared due to ionisation of the dye under mild alkaline conditions. The dyes exhibited good to excellent fastness properties on the polyester fabric.     

Mechanical properties and morphology of polymer blends of poly(ethylene terephthalate) and semiflexible thermotropic liquid crystalline polyesters

Two thermotropic liquid crystalline polyesters (TLCPs) with long flexible spacer groups in the main chain were prepared by melt polymerization: one was a homopolymer with only decane groups (LCPHO) and the other was a copolymer with hexane or decane groups (LCPCO) between mesogen units. These polyesters were blended with a matrix polymer of poly(ethylene terephthalate) (PET). Scanning electron microscopy (SEM) revealed the excellent interfacial adhesion between polyester and PET, and the large aspect ratio of polyester microfibrils in the blend fiber made by extruding and drawing the blend through a die. The aspect ratio was estimated by using the modified Halpin-Tsai equation. The fiber with LCPHO showed more extensive fibril formation than that with LCPCO.