Modelling and analysis of productivity teamwork based on information technology

Organizations are usually represented and evaluated by their output. Therefore, all procedures and models which may affect and improve output attract the attention of researchers. The effects of organizing work teams as one essential resource of organizations, in addition to the structure, size and effectiveness of the team, are also considered important factors. This paper reports on an investigation performed to define a model to explain how the results of teamwork may improve production, while considering the role of IT as an effective parameter. Also, it is shown that if there is a number of IT improvement options, there may be a mix of IT improvement and team size increase that will yield the most cost efficient increase in team output.     

Bearing fault detection using wavelet packet transform of induction motor stator current

Induction motor vibrations, caused by bearing defects, result in the modulation of the stator current. In this research, bearing defect is detected using the stator current analysis via Meyer wavelet in the wavelet packet structure, with energy comparison as the fault index. The advantage of this method is in the detection of incipient faults. The presented method is evaluated using experimental signals. Sets of data are gathered before and after using defective bearings. Compared to conventional methods, the superiority of the proposed method is shown in the success of fault detection.     

Scheduling flowshops with condition-based maintenance constraint to minimize expected makespan

Flexible job-shop scheduling problem (FJSP) is an extended traditional job-shop scheduling problem, which more approximates to practical scheduling problems. This paper presents a multi-objective genetic algorithm (MOGA) based on immune and entropy principle to solve the multi-objective FJSP. In this improved MOGA, the fitness scheme based on Pareto-optimality is applied, and the immune and entropy principle is used to keep the diversity of individuals and overcome the problem of premature convergence. Efficient crossover and mutation operators are proposed to adapt to the special chromosome structure. The proposed algorithm is evaluated on some representative instances, and the comparison with other approaches in the latest papers validates the effectiveness of the proposed algorithm.     

The non-cooperative game theory for trades in B2B electronic market

B2B electronic market facilitates the transactions among businesses. It consists of buyers, sellers, and the market owner. But most of these markets could not generate the expected profits for all market participants. In this paper, expected profit for each market participant has been considered in a neutral market with double auction. Based on these profit functions, optimal quantities of bids and offers are determined for buyers and sellers. Then, a model based on game theory is proposed that leads to recognize optimal strategies for game players that include buyers, sellers, and the market owner. Using the optimal strategies will satisfy the game participants and maximize their benefits. Additionally, a numerical example is illustrated to better describe the proposed model.     

An experimental investigation of cylindrical wire electrical discharge turning process

The cylindrical wire electrical discharge turning (CWEDT) process was developed to generate precise cylindrical forms on hard, difficult to machine materials. A precise, flexible, and corrosion-resistant submerged rotary spindle was designed and added to a conventional five-axis CNC wire electrical discharge machine (EDM) to enable the generation of free-form cylindrical geometries. The hardness and strength of the work material are no longer the dominating factors that affect the tool wear and hinder the machining process. In this study, the effect of machining parameters on surface roughness (R _a) and roundness in cylindrical CWEDT of a AISI D3 tool steel is investigated. The selection of this material was made taking into account its wide range of applications in tools, dies, and molds and in industries such as punching, tapping, reaming, and so on in cylindrical forms. Surface roughness and roundness are chosen as two of the machining performances to verify the process. In addition, power, pulse off-time, voltage, and spindle rotational speed are adopted for evaluation by full factorial design of experiments. In this case, a 2²?×?3² mixed full factorial design has been selected considering the number of factors used in the present study. The main effects of factors and interactions were considered in this paper, and regression equations were derived using response surface methodology. Finally, the surfaces of the CWEDT parts were examined using scanning electron microscopy (SEM) to identify the macro-ridges and craters on the surface. Cross sections of the EDM parts were examined using the SEM and microhardness tests to quantify the sub-surface recast layers and heat-affected zones under specific process parameters.     

Multivariable data analysis of a cold rolling control system to minimise defects

This paper focuses on the application of principal component analysis (PCA) to thoroughly analyse and interpret multidimensional data from a cold rolling process. The analysis includes the effects of variables on the final properties of strips in a cold rolling mill. Unscrambler software was used to analyse and identify hidden variables. Variable correlations were also used to derive correlations between the control parameters. The results of this research will be used to improve the selection of material in order to reduce the occurrence of defects in the cold rolling process and to improve the adjustment of the set points that are performed in every pass or section of the cold rolling process. The hot rolled strips that enter the cold rolling mill are made of different materials and are produced by different strip manufacturers. Some strips break during the thickness reduction process in the cold rolling mill. This paper focuses on two possible causes of breakage: non-uniform strip material properties and failures in the rolling mill process. Two types of rolled strips (those that break and those that do not break) were compared to identify causes of breakage. The results indicate that breakages are caused by material or process failures. PCA was applied to the dataset in order to identify and analyse the relationships between the variables in the process. This information was used to interpret and diagnose the process behaviour. Swarm analysis and relating observations to process behaviour were able to distinguish between different start-up conditions, and between desirable and undesirable process conditions.     

Introduction of an empirical classification system for evaluating tunneling impact on the discharge of springs (TIS) in the surrounding areas

Bulletin of Engineering Geology and the Environment - Water inflow caused by tunneling can have severe impacts on the springs’ discharge rate. If these impacts have not been predicted...     

Stability analysis of shallow tunnels subjected to eccentric loads by a boundary element method

In this paper, stress behavior of shallow tunnels under simultaneous non-uniform surface traction and symmetric gravity loading was studied using a direct boundary element method(BEM). The existing fullplane elastostatic fundamental solutions to displacement and stress fields were used and implemented in a developed algorithm. The cross-section of the tunnel was considered in circular, square, and horseshoe shapes and the lateral coefficient of the domain was assumed as unit quantity. Double-node procedure of the BEM was applied at the corners to improve the model including sudden traction changes. The results showed that the method used was a powerful tool for modeling underground openings under various external as well as internal loads. Eccentric loads significantly influenced the stress pattern of the surrounding tunnel. The achievements can be practically used in completing and modifying regulations for stability investigation of shallow tunnels.     

The effect of sintering time on the densification and mechanical properties of a mechanically alloyed Cr–Mn–N stainless steel

Sintering is an essential stage in powder metallurgy, which affects the final microstructure and performance of the part. This study is concerned with the sintering and mechanical behaviors of Fe–18Cr–8Mn–0.9N stainless steel prepared from mechanically alloyed amorphous/nanocrystalline powders. The contribution of sintering time to the densification at 1100 °C is considered and a sluggish densification is found for the alloy. Furthermore, the correlation between the microstructure and mechanical properties of the fabricated porous parts is studied. It is found that the yield stress is affected by both porosity and the material’s intrinsic yield strength. Nonetheless, the effect of porosity on the overall hardness typically prevails over the effect of matrix hardness. Interestingly, even after sintering at 1100 °C for up to 20 h, the nanometric structure of the material is retained.