The catalytic deacidification of acidic crude oil using Cu-doped alkaline earth metal oxide catalysts

Naphthenic acids (NAs) tend to cause operational problems that can lead to the deactivation of catalysts. To overcome the problem, catalytic deacidification was introduced utilizing an ammonia solution in ethylene glycol with the aids of alkaline earth metal catalyst with alumina as a support. The initial total acid number observed for NAs in n-dodecane was 4.21 mg KOH/g. In total, 1,000 mg/L of 0.4% NH₃-EG were used as the acid removal agent. Calcium, barium, and magnesium catalysts were tested in this study. The results showed Cu/Ca/Al₂O₃ was found to be the best catalyst that could be used to enhance the reaction.     

Thermal properties and aging characteristics of chemically modified oil palm ash-filled natural rubber composites

The chemically modified oil palm ash (OPA) with the cetyltrimethylammonium bromide (CTAB) solution was prepared prior to compounding with the natural rubber and other curing ingredients. The aging resistance and thermal stability of CTAB-modified OPA-filled natural rubber composites were evaluated in the same manner as non-modified OPA samples. The retention tensile properties after thermal aging was measured and based on the result shown, the CTAB-modified OPA-filled natural rubber composites imparted insignificant effect to aging resistance as compared to the non-modified OPA-filled natural rubber composites at very low OPA loading; however, the effect became apparent beyond 3 phr OPA loading where the CTAB-modified OPA-filled natural rubber composites provided better aging resistance than the corresponding non-modified OPA-filled natural rubber composites. The thermogravimetric analysis indicated that the CTAB-modified OPA-filled natural rubber composites exhibited lower thermal stability which showed lower temperature at their respective weight loss and lesser char residue than that of non-modified OPA-filled natural rubber composites. This was attributed to the CTAB which started to decompose at the temperature of 210 °C. However, for the range from ambient temperature to 210 °C, the CTAB-modified OPA-filled natural rubber composites produce better thermal stability than those of non-modified OPA-filled natural rubber composites.     

A review of the stabilization of tropical lowland peats

The Deep Mixing Method, which involves the formation of in situ stabilized peat columns, is suitable for deep peat stabilization, whereas the mass stabilization technique is used to stabilize the soil of shallow peat deposits instead of the costly and problematic removal and replacement method. The concept of soil-cement stabilization involves the addition of water to cement, resulting in a chemical process known as cement hydration. Stabilization of peat by cement, which requires a significant strength increase in the cement-stabilized peat or organic soil, is attributed largely to physicochemical reactions that include cement hydration, hardening of the resulting cement paste and interactions between soil substances and primary and secondary cementation hydration products. The factors that affect these physicochemical reactions and the interactions of peat soil-cementation products that influence peat stabilization are the amount of solid particles, the water: soil ratio, the quantity of binder, the presence of humic and/or fulvic acids, the soil pH and the amount of organic matter in the peat. With the Air Curing Technique, stabilized peat samples for unconfined compressive strength (UCS) tests were kept at a normal air temperature of 30 ± 2 °C and strengthened by gradual moisture content reduction instead of the usual water-curing technique or water submersion methods that have been common practice in past experiments involving the stabilization of peat with cement. The principle of using the Air Curing Technique to strengthen stabilized peat is that peat soil at its natural moisture content contains sufficient water (water content from 198 to 417 %) that, when mixed with cement, a curing process takes place that causes the stabilized peat soil to gradually lose its moisture content and to become drier and harder throughout the curing period. This process does not require the addition of water.     

Effects of Modified Atmosphere Packaging with Various Carbon Dioxide Composition on Biogenic Amines Formation in Indian Mackerel (Rastrelliger kanagurta) stored at 5 ± 1°C

The profile of major biogenic amines was investigated in Indian mackerel packed in modified atmosphere for up to 12 days at 5 ± 1°C. Beheaded and gutted Indian mackerel was packed under different carbon dioxide compositions to study the effects on biogenic amines formation. The treatments were control air (C), vacuum packaging (VP), 30% CO₂/65% N₂/5% O₂ (M30C), 60% CO₂/35% N₂/5% O₂ (M60C), 80% CO₂/15% N₂/5% O₂ (M80C) and 100% CO₂ (M100C). Each amine responded differently to different CO₂ levels. After 12 days of storage, concentrations of histamine were reduced by 6.4%, 8.5%, 70.3%, 78.8% and 90.2% in fish packed under VP, M30C, M60C, M80C and M100C, respectively as compared with control air. Changes in putrescine and cadaverine showed a similar pattern. Gas mix of M30C and VP stimulated the formation of tyramine reaching 203 and 172 ppm, respectively. Higher composition of CO₂ had a significant inhibitory effect on tyramine concentration (p < 0.05). There were parallel increases of putrescine and spermidine in C, VP and M30C. No significant effect of CO₂ was observed on spermine (p > 0.05). After 9 days of storage, more than 300 ppm of histamine was detected in mackerel packed in VP and M30C; therefore, these atmospheres pose a histamine intoxication risk. Copyright © 2013 John Wiley & Sons, Ltd.     

Inhibition of Aluminum Alloy Corrosion in 0.5 M Nitric Acid Solution by 4-4-Dimethyloxazolidine-2-thione

The corrosion inhibition of Al-Alloy (Al2024) in 0.5 M nitric acid solution at 30 °C was achieved using 4-4-dimethyloxazolidine-2-thione (DMT) as a corrosion inhibitor. The electrochemical performance of the DMT was studied by electrochemical impedance spectroscopy (EIS), potentiodynamic polarization measurements, and scanning electron microscopic study (SEM). The results indicated that DMT acts as an inhibitor for Al2024 in 0.5 M nitric acid. Polarization curves indicated that DMT was a mixed-type inhibitor. Inhibition efficiencies were observed to be increased with an increase in DMT concentration and attains approximately to 93.4% at 2 mM of DMT in 0.5 M nitric acid. The adsorption of DMT model on Al2024 surface obeyed in accordance with Langmuir adsorption isotherm model. The value of the free energy of adsorption ΔG _ads indicated that the adsorption of DMT molecule was a spontaneous process and was typical of physical and chemical adsorption.     

Effect of a post-weld heat treatment on the mechanical and microstructure properties of AA6061 joints welded by the gas metal arc welding cold metal transfer method

This work studies the effect of a post-weld heat treatment (PWHT) on the mechanical and microstructure properties of an AA6061 sample welded using the gas metal arc welding (GMAW) cold metal transfer (CMT) method. The CMT method was used because the method provides spatter-free welding, outstanding gap bridging properties, low heat input and a high degree of process flexibility. The welded samples were divided into as-welded and PWHT samples. The PWHTs used on the samples were solution heat treatment, water quenching and artificial aging. Both welded samples were cut according to the ASTM E8M-04 standard to obtain the tensile strength and the elongation of the joints. The failure pattern of the tensile tested specimens was analysed using scanning electron microscopy (SEM). A Vickers microhardness testing machine was used to measure the hardness across the joints. From the results, the PWHTs were able to enhance the mechanical properties and microstructure characteristics of the AA6061 joints welded by the GMAW CMT method.     

Woven hybrid composites: Tensile and flexural properties of oil palm-woven jute fibres based epoxy composites

In this research, tensile and flexural performance of tri layer oil palm empty fruit bunches (EFB)/woven jute (Jw) fibre reinforced epoxy hybrid composites subjected to layering pattern has been experimentally investigated. Sandwich composites were fabricated by hand lay-up technique in a mould and cured with 105 °C temperatures for 1 h by using hot press. Pure EFB and woven jute composites were also fabricate for comparison purpose. Results showed that tensile and flexural properties of pure EFB composite can be improved by hybridization with woven jute fibre as extreme woven jute fibre mat. It was found that tensile and flexural properties of hybrid composite is higher than that of EFB composite but less than woven jute composite. Statistical analysis of composites done by ANOVA-one way, it showed significant differences between the results obtained. The fracture surface morphology of the tensile samples of the hybrid composites was performed by using scanning electron microscopy.     

Performance analysis of a double-pass photovoltaic/thermal (PV/T) solar collector with CPC and fins

The use of PV/T in combination with concentrating reflectors has a potential to significantly increase power production from a given solar cell area. A prototype double-pass photovoltaic-thermal solar air collector with CPC and fins has been designed and fabricated and its performance over a range of operating conditions was studied. The absorber of the hybrid photovoltaic/thermal (PV/T) collector under investigation consists of an array of solar cells for generating electricity, compound parabolic concentrator (CPC) to increase the radiation intensity falling on the solar cells and fins attached to the back side of the absorber plate to improve heat transfer to the flowing air. Energy balance equations have been developed for the various nodes of the system. Both thermal and electrical performance of the collector are presented and discussed.     

Performance of H‐ZSM‐5‐supported bimetallic catalysts for the combustion of polluting volatile organic compounds in air

The performance of H‐ZSM‐5‐supported bimetallic catalysts with chromium as the base metal in the combustion of ethyl acetate and benzene is reported. A reactor operated from 100 to 500 °C at a gas hourly space velocity (GHSV) of 32 000 h^?1 was used for study of the activity. A combination of 1.0 wt% chromium and 0.5 wt% copper yielded a catalyst (Cr_1.0Cu_0.5/Z) with improved conversion and carbon dioxide yield. Cr₂O₃ (Cr³⁺) and CuO (Cu²⁺) were the predominant metal species in the catalyst. In agreement with the Mars–van Krevelen model, improved reducibility of Cr³⁺ in the presence of Cu²⁺ led to an improvement in activity. The copper content in Cr_1.0Cu_0.5/Z also favored the formation of deep combustion products. Condensation and subsequent growth of coke precursors in the catalyst pores led to the formation of a softer and less aromatic coke fraction while dehydrogenation activity on acid sites formed a harder and more aromatic coke fraction. The use of Cr_1.0Cu_0.5/Z favored the formation of lower molecular weight intermediates, leading to reduction in formation of softer coke. Copyright © 2005 Society of Chemical Industry     

A novel dengue fever (DF) and dengue haemorrhagic fever (DHF) analysis using artificial neural network (ANN)

Dengue fever (DF) is an acute febrile viral disease frequently presented with headache, bone or joint and muscular pains, and rash. A significant percentage of DF patients develop a more severe form of disease, known as dengue haemorrhagic fever (DHF). DHF is the complication of DF. The main pathophysiology of DHF is the development of plasma leakage from the capillary, resulting in haemoconcentration, ascites, and pleural effusion that may lead to shock following defervescence of fever. Therefore, accurate prediction of the day of defervescence of fever is critical for clinician to decide on patient management strategy. To date, no known literature describes of any attempt to predict the day of defervescence of fever in DF patients. This paper describes a non-invasive prediction system for predicting the day of defervescence of fever in dengue patients using artificial neural network. The developed system bases its prediction solely on the clinical symptoms and signs and uses the multilayer feed-forward neural networks (MFNN). The results show that the proposed system is able to predict the day of defervescence in dengue patients with 90% prediction accuracy.