A vertically integrated tool for automated design of /spl Sigma//spl Delta/ modulators

We present a tool that starting from high-level specifications of switched-capacitor (SC) /spl Sigma//spl Delta/ modulators calculates optimum specifications for their building blocks and then optimum sizes for the block schematics. At both design levels, optimization is performed using statistical techniques to enable global design and innovative heuristics for increased computer efficiency as compared with conventional statistical optimization. The tool uses an equation-based approach at the modulator level, a simulation-based approach at the cell level, and incorporates an advanced /spl Sigma//spl Delta/ behavioral simulator for monitoring and design space exploration. We include measurements taken from two silicon prototypes: (1) a 16 b @ 16 kHz output rate second-order /spl Sigma//spl Delta/ modulator; and (2) a 17 b @ 40 kHz output rate fourth-order /spl Sigma//spl Delta/ modulator. Both use SC fully differential circuits and were designed using the proposed tool and manufactured in a 1.2 /spl mu/m CMOS double-metal double-poly technology.<>     

Transient complete remission of acute lymphoblastic leukemia in relapse after allogeneic bone marrow transplantation induced by donor leukocyte transfusions

We report the case of a young patient with refractory acute lymphoblastic leukemia relapse, after allogeneic bone marrow transplantation, who was treated by donor leukocyte infusions. We observed potent adoptive immunotherapy which produced a cytologic complete remission and total chimeric state. This was of short duration and the patient died of severe graft-versus-host disease. We present a short summary of the literature concerning acute lymphoblastic leukemia and donor leukocyte infusions.     

Investigation of optical losses in photoelastic and ridge waveguides in GaAs-AlGaAs heterostructures

Two approaches have been used to fabricate stable photoelastic waveguides with planarized surfaces on GaAs-AlGaAs heterostructures. The first approach uses tensile Ni/sub 3/GaAs stressors formed by metal-semiconductor reactions. The second approach uses inert, refractory and compressive stressors, such as RF sputtered W and RF co-sputtered WNi films. For comparison purposes, ridge waveguides have also been fabricated using the same heterostructure by a dry etching technique. Optical losses of photoelastic waveguides, measured by Fabry-Perot (FP) method at a wavelength of 1.53 /spl mu/m, are comparable to or better than those of the ridge waveguides. Material loss appears to be the primary loss mechanism in both photoelastic and ridge waveguides. These results indicate that the photoelastic waveguide processing technique reported in this study is a promising alternative to commonly used dry etching techniques for planarization.     

Imitation and pantomime in high-functioning adolescents with autism spectrum disorders

A study was designed to test 2 alternative hypotheses--a symbolic hypothesis and an executive function hypotheses--for the imitation and pantomime deficits found in previous studies of autism. The subjects were 17 adolescent high-functioning subjects with autism spectrum disorders and 15 clinical comparison subjects who were matched on chronological age and verbal IQ. Meaning and sequence were manipulated in facial and manual imitation tasks. Sequence was manipulated in the pantomime and control tasks. Recognition memory and motor control tasks were matched to the experimental tasks. The results provided no support for the symbolic deficit hypothesis; meaning aided rather than hindered the performance of the group with autism. Partial support for the executive deficit hypothesis was found. There were no group differences on motor control tasks, and few on the memory control tasks, arguing against deficits in motor initiation, basic motor coordination, or visual recognition memory.     

Measurement and prediction of pressure drop in two-phase flow

Experimental data for air–water two-phase co-current flow in two different pipe diameters were used to test the prediction of pressure drop by a number of existing theories and correlations. Several models are shown to be useful for prediction, particularly with the stratified regimes which have proved difficult to handle in the past. The model suggested by Olujic proved to be of particular value.     

An assessment of potential nonlinear circuit models for thecharacterization of resonant tunneling diodes

The intrinsically fast process of resonant tunneling through double barrier heterostructures along with the existence of negative differential resistance in the current-voltage characteristic of these structures has led to their implementation as sources for high frequency electromagnetic energy. While sources based upon resonant tunneling diodes (RTDs) have produced frequency of oscillations up to 712 GHz, only microwatt levels of performance has been achieved above 100 GHz. Since stability criteria plays critical role in determining the deliverable power of any oscillator, a physically accurate equivalent-circuit model for the RTD is extremely important for optimizing the dynamics of the device-cavity package. This study identifies a distinctly new equivalent circuit model for characterizing the modes of oscillation in RTD-based sources. Specifically, in order to exhibit the fundamental self-oscillations and the overall I-V characteristics (plateau structure and hysteresis) observed experimentally, an accurate circuit model of the RTD must incorporate: (i) a quantum-well inductance which directly chokes the nonlinear conductance and, (ii) a nonlinear access resistance, associated with the accumulation of charge in the injection region of the double barriers, with a nonlocal dependence on the bias across the double barrier structure     

The effect of bandwidth allocation policies on delay inunidirectional bus networks

We consider the problem of allocating bandwidth fairly to each node in a shared, unidirectional bus network. We focus on the p_i persistent protocol, since these are open loop policies designed to operate well in high speed networks, which have a very large bandwidth-delay product and feedback in the upstream direction is not available in a timely manner. First, we introduce an improvement to the basic p_i persistent protocol, in which we replace random coin tosses with a deterministic counting algorithm, and thereby reduce the delays for all nodes for any given choice of {p_i}. We then describe an exact method for calculating average packet delays and queue lengths in both the p_i persistent and our new deterministic n out of m protocols, based on the regenerative approach of Georgiades et al. (1987). These delay results, together with simulation measurements, show that both of these protocols still waste some bandwidth. After presenting a lower bounding argument to show that some wasted bandwidth is inevitable in all such distributed access control schemes, assuming a passive bus without feedback in the upstream direction, we show that changing the bus to unidirectional point-to-point links between (very simple) active interfaces at each node allows us to construct distributed access schemes that require no upstream feedback and are both work conserving and fair. To illustrate how this can be done, we introduce the p_i preemptive protocol, in which each node randomly inserts its own packets into the traffic arriving from upstream. We derive a simple and effective heuristic for calculating the preemption probability for each node, and use simulation to show how well it equalizes the delays at each node     

Structure and mechanical properties of polyethylene-fullerene composites

The microhardness of films of fullerene-polyethylene composites prepared by gelation from semidilute solution, using ultrahigh molecular weight polyethylene (PE) (6×10⁶), has been determined. The composite materials were characterized by optical microscopy and X-ray diffraction techniques. The microhardness of the films is shown to increase notably with the concentration of fullerene particles within the films. In addition, a substantial hardening of the composites is obtained after annealing the materials at high temperatures (T _a=130 °C) and long annealing times (t _a=10⁵s). The hardening of the composites with annealing temperature has been identified with the thickening of the PE crystalline lamellae. Comparison of X-ray scattering data and the microhardness values upon annealing leads to the conclusion of phase separation of C₆₀ molecules from the polyethylene crystals within the material. The temperature dependence is discussed in terms of the independent contribution of the PE matrix of the C₆₀ aggregates to the hardness value.     

The use of force modulation microscopy to investigate block copolymer morphology

Force modulation microscopy (FMM) is used to characterize the external surface and internal fracture surface morphologies of three different block copolymer samples. A roll-cast poly(styrene-butadiene-styrene) triblock copolymer film, spin-coated poly(styrene-b-methyl methacrylate) thin films, and an ultrathin poly(styrene-b-hexyl isocyanate) rod-coil block copolymer film were investigated. For each sample, height and elasticity images were obtained for the same areas allowing direct comparison. The elasticity images obtained using force modulation microscopy were independent of surface roughness and found to exhibit better contrast and spatial resolution of the respective block copolymer domains than the height images. The lateral resolution of the elasticity images was sufficient to show microphase separated domains having length scales as small as about 10 nm. The poly(styrene-b-methyl methacrylate) samples demonstrate that FMM can even be successfully used to study block copolymers in which both blocks are glassy under the conditions of measurement.     

Sliding wear of Al2O3P/6061 Al composite

The mild sliding wear behaviour of a 15 vol % Al₂O_3P/6061 Al composite has been investigated by using a pin-on-disc reciprocating sliding machine. The composite has been shown to exhibit an excellent wear resistance as compared to the unreinforced matrix alloy. The wear rate of the composite under dry wear conditions with a 12N load is approximately one tenth of that in the 6061 aluminium alloy. The wear rate of the composite under lubrication with 15W/40 gear oil under a 100N load is only one thousandth ofthat in the 6061 aluminium alloy.The dry wear resistance of an over-aged sample is shown here to be better than a peak aged or under-aged sample when the composite was aged at 160°C. The coefficient of friction of the composite was approximately 0.5–0.6 under dry conditions and 0.07 in lubricated wear experiments.In the initial stage, the worn surface of the composite under dry conditions is primarily composed of ploughed grooves and ductile tear. The composite makes a conducting contact with the steel pin. The worn surface is composed of compacted powder and the contact potential gradually increases when the period of the wear experiment goes beyond 2 h.