Security of the Cao-Li public key cryptosystem

The author shows that the Cao-Li cryptosystem proposed [1991] is not secure. Its private key can be reconstructed from its public key using elementary means such as LU-decomposition and the Euclidean algorithm     

Long-term effect of inducible silent ischaemia on left ventricular systolic function

A new method of thin section preparation of III-V semiconductors and multilayers for transmission electron microscopy (TEM) is presented that exhibits considerable advantages over conventional methods such as ion beam milling and jet thinning. GaAs thin films and multilayers of GaAs/In chi Ga1-chi As/GaAs are grown over an etch release layer of AlAs on GaAs substrates by molecular beam epitaxy (MBE). Planar TEM sections prepared by selective etching from these samples show improved ability to image film morphology and dislocation arrangements, and the resulting large thin electron transparent areas facilitate dislocation density measurements and detection of spatial variations. Avoidance of radiation effects and wedge shaping, both common to ion milled samples, allows this method to be used to prepare uniform thickness standards of single layer GaAs films for EDS analysis or lattice imaging.     

Study on the propagation of inlet flow distortion in axial compressor using an integral method

 An integral method is investigated and developed in the current work. The effects of the parameters of inlet distortions on the trend of downstream flow feature in compressor are simulated. Other than the drag-to-lift ratio of the blade and the inlet incidence angle, it is found that the distorted inlet velocity is another essential parameter to control the distortion in propagation. Based on this study, a novel critical distortion line and corresponding critical distortion factor are proposed to express the effect of the two essential inlet parameters on the propagation of distortion, namely, the inlet incidence angle and the distorted inlet velocity. From the viewpoint of compressor efficiency, the propagation of inlet flow distortion is further described by a compressor critical performance and its critical characteristic. The results present a useful physical insight to an axial flow compressor behavior and asymptotic behavior of the propagation of inlet distortion, and confirm the active role of compressor in determining the velocity distribution when compressor responds to an inlet flow distortion. Received: 20 December 2001 / Accepted: 21 August 2002 The authors would like to thank HQ RSAF for permission to publish this work, their financial support and encouragement. The first author wants to acknowledge Prof. Frank Marble of California Institute of Technology, for bringing the problem to the author's attention and for his helpful discussion.     

A dynamic frequency grid allocation scheme for the efficient designof equiripple FIR filters

In the design of a digital filter, the frequency response is often optimized to meet a given set of specifications on a dense grid of frequency points. The density of the frequency grid points must be sufficiently high so that the frequency response of the filter does not violate the specifications at frequencies in between the grid points. However, the computational complexity of the design process and the storage requirements of the computer increase with the number of frequency grid points. We propose a novel dynamic: grid point allocation technique for the design of minimax optimum FIR filter. It uses a sparse frequency grid but will produce a design that is the same as one designed on very dense frequency grid points. It requires significantly less computer time and memory resources compared with fixed grid point algorithms     

Analysis and characterization of traveling-wave electrode in electroabsorption modulator for radio-on-fiber application

Comparing with a lumped electroabsorption modulator (EAM), we show the merits of a long EAM with traveling-wave electrode with high radio-frequency (RF) gain that could be used in high-frequency analog application. By terminating the RF output port with the characteristic impedance of 30 /spl Omega/, the device exhibited a large enhancement of 6 dB above 10 GHz in the electrical-to-optical response and a wide fractional bandwidth as estimated from simulation. In addition, an input impedance matching circuit of stub embedded on the device chip was found to be very effective for improving RF characteristics in the narrow band of frequency.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。