MODELING AND MEASUREMENTS OF INFRARED DRYERS FOR COATED PAPER

We have developed models to determine the radiative heat transfer of infrared dryers. Using the models, the efficiencies of several IR constructions are calculated. The radiation properties of all parts of the IR dryer are measured with an IT-IR spectrometer using integrating sphere techniques. With these models and measured results, the total efficiencies of several dryer constructions are calculated for: an electric dryer with a pambolic mirror, an elecmc dryer with a flat ceramic mirror, and a gas-fired dryer. The effect of a back reflector on these dryers is also calculated. The efficiencies of all these dryers are compared to each other.     

Influence of High-Temperature Heat Treatment on Barrier and Functional Properties of Polyolefin-Coated Papers

In this study, the effect of heat treatment on barrier and functionality of polyolefin-coated papers was investigated. The aim was to find the optimal improvements on barrier without losing the applicability of the materials due to physical damages. The results of the study proved considerable improvement in barrier characteristics of the structures. Both water vapor and oxygen transmission rates of LDPE-coatings decreased linearly following the set-temperature until 200°C. At this point, the treatment caused a continuing decrease in oxygen transmission achieving 10 × lower transmission levels than the untreated structure, whereas moisture transport faced corresponding but lower increase. This was considered to be caused by the difference in diameter of the H₂O and O₂ molecules; the smaller water molecules are able to penetrate between spherulites, whose size increased due to higher treatment temperature followed by cooling.     

Layered dielectric–magnetic composite structures for Rf-applications

In this paper multilayer magnetic–dielectric composite structures for high frequency applications are introduced. The 0–3 type dielectric and magnetic composites with homogeneously distributed ceramic inclusions were fabricated by mixing extrusion and injection moulding. Magnetic Yttrium Iron Garnet (YIG) and Z-type Hexaferrite (HexaZ) as well as paraelectric Barium Strontium Titanate (BST) powders were used to enhance the permittivity and permeability of the composites. The magnetic–dielectric multilayer composites were constructed by hot-laminating magnetic and dielectric layers in turn to create a solid 2-2 type composite structure. The microstructure, high frequency dielectric and magnetic properties of individual layers and 2-2 composites were investigated and measured. The measurement results indicate that such multimaterial multilayer structures are good candidates for components with reduced dielectric and magnetic losses. Moreover, the observed good frequency stability and the cut-off frequencies above 1 GHz suggested that the composites could be utilized in, e.g., sophisticated functional circuit boards and RF devices.     

QoS support for an all IP system beyond 3G

Mobile radio systems beyond the third generation will evolve into all-IP systems, integrating Internet and mobile system advantages. The BRAIN project is developing a system architecture which combines local coverage broadband radio access systems based on HIPERLAN/2 with several wider-coverage mobile radio systems, enabling full coverage of seamless IP-based services for users in hot spot areas and on the move. End-to-end QoS provision is one of the major challenges in the design of such a system and must be supported by the application, network, and wireless access layers. This article proposes a QoS system architecture, including the terminal architecture, the IP-based access network, and the main characteristics of the enhancements to the air interface based on HIPERLAN/2 focusing on its wireless QoS support     

Fish bile used to detect estrogenic substances in treated sewage water

Endocrine disrupting effects on fish associated with sewage treatment effluents have been demonstrated in several studies. To investigate if the effluents from two modern Swedish sewage treatment plants contained estrogenic substances, juvenile rainbow trout were exposed to sewage water before and after the last treatment step which is a sand filter. As a biomarker for estrogenic effect, vitellogenin was analysed in the blood plasma of the exposed fish. To identify substances possibly responsible for the effect, bile fluid from the exposed fish were analysed with GC/MS. Elevated levels of vitellogenin were only seen in the fish exposed at one of the sewage treatment plants, the one with shorter residence time in the biological treatment steps, which suggests that the residence time is of importance for the ability to reduce the amount of estrogenic substances in the sewage water. The highest elevation of vitellogenin was seen in the fish exposed to water before the sand filter, which indicates that the sand filter contributes to further reduction of estrogenic substances in the sewage water. In bile from the same group of fish, considerably higher concentrations of estrone, bisphenol A and 4-nonylphenol (4.0 microg/g bile, 23 microg/g bile and 24 microg/g bile, respectively) were observed compared to bile from control fish (<0.04 microg/g bile, 0.21 microg/g bile, and 3.5 microg/g bile, respectively). The more potent steroidal estrogens were suggested to be major contributors to the observed estrogenic effect, although xenoestrogens were detected at higher concentrations in the bile fluid.     

Energy Harvesting Research: The Road from Single Source to Multisource

Energy harvesting technology may be considered an ultimate solution to replace batteries and provide a long‐term power supply for wireless sensor networks. Looking back into its research history, individual energy harvesters for the conversion of single energy sources into electricity are developed first, followed by hybrid counterparts designed for use with multiple energy sources. Very recently, the concept of a truly multisource energy harvester built from only a single piece of material as the energy conversion component is proposed. This review, from the aspect of materials and device configurations, explains in detail a wide scope to give an overview of energy harvesting research. It covers single‐source devices including solar, thermal, kinetic and other types of energy harvesters, hybrid energy harvesting configurations for both single and multiple energy sources and single material, and multisource energy harvesters. It also includes the energy conversion principles of photovoltaic, electromagnetic, piezoelectric, triboelectric, electrostatic, electrostrictive, thermoelectric, pyroelectric, magnetostrictive, and dielectric devices. This is one of the most comprehensive reviews conducted to date, focusing on the entire energy harvesting research scene and providing a guide to seeking deeper and more specific research references and resources from every corner of the scientific community.     

Line creep in paper peeling

The dynamics of a “peeling front” or an elastic line is studied under creep (constant load) conditions. Our experiments show in most cases an exponential dependence of the creep velocity on the inverse force (mass) applied. In particular, the dynamical correlations of the avalanche activity are discussed here. We compare various avalanche statistics to those of a line with non-local elasticity, and study various measures of the experimental avalanche-avalanche and temporal correlations such as the autocorrelation function of the released energy and aftershock activity. From all these we conclude, that internal avalanche dynamics seems to follow “line depinning”-like behavior, in rough agreement with the depinning model. Meanwhile, the correlations reveal subtle complications not implied by depinning theory. Moreover, we also show how these results can be understood from a geophysical point of view.     

Modeling errors due to Timoshenko approximation in damage identification

The use of accurate computational models for damage identification problems may lead to prohibitive costs. Damage identification problems are often characterized as inverse ill-posed problems. Thus, the use of approximate models such as simplified physical and/or reduced-order models typically yields misleading results. In this paper, we carry out a preliminary study on a particular simplified physical model, the Timoshenko beam model in the context of damage identification. The actual beam is a two-dimensional relatively high aspect ratio (thickness/length) beam with a distributed damage that is modeled as a spatially varying Young modulus. We state the problem in the Bayesian framework for inverse problems and carry out approximative marginalization over the related modeling errors. The numerical experiments suggest that the proposed approach yields more stable results than using the Timoshenko beam model as an accurate model. Due to the severity of the Timoshenko approximation, however, the posterior error estimates of the proposed approach are not always feasible in the probabilistic sense.