Enhancement mode InP MISFET's with sulfide passivation andphoto-CVD grown P3N5 gate insulators

High performance enhancement mode InP MISFET's have been successfully fabricated by using the sulfide passivation for lower interface states and with photo-CVD grown P₃N₅ film used as gate insulator. The MISFET's thus fabricated exhibited exhibited pinch-off behavior with essentially no hysteresis. Furthermore the device showed a superior stability of drain current. Specifically under the gate bias of 2 V for 10⁴ seconds the room temperature drain current was shown to reduce from the initial value merely by 2.9% at the drain voltage of 4 V. The effective electron mobility and extrinsic transconductance are found to be about 2300 cm ²/V·s and 2.7 mS/mm, respectively. The capacitance-voltage characteristics of the sulfide passivated InP MIS diodes show little hysteresis and the minimum density of interface trap states as low as 2.6×10¹⁴/cm² eV has been attained     

The possible influence of the menstrual cycle on the adherence of Candida albicans to human buccal epithelial cells in vitro

Although the influence of the menstrual cycle on both vaginal candidosis and Candida albicans adherence to vaginal epithelial cells in vitro has been shown to be significant, similar studies have not been made on oral candidosis and adherence to buccal epithelial cells. The aim of this study was therefore to use an in vitro adherence assay to investigate the possible influence of the menstrual cycle on the adherence of C. albicans to buccal epithelial cells. Epithelial cells were collected from a single, healthy, female volunteer on days 5, 15, 22 and 28 of six menstrual cycles. Adherence of C. albicans was significantly higher to buccal epithelial cells collected on day 5 of the menstrual cycle when compared with days 15, 22 and 28, both in terms of the percentage of buccal epithelial cells with adherent C. albicans and the number of C. albicans adhering per 200 buccal epithelial cells in four out of six menstrual cycles (p < 0.001). This result indicates that hormonal influences should be considered when buccal epithelial cells are used in vitro to assess candidal adherence and may implicate hormonal factors in the aetiology of oral candidosis.     

Ultra-wideband (from DC to 110 GHz) CPW to CPS transition

A new ultra-wideband, low-loss and small-size coplanar waveguide (CPW) to coplanar strip (CPS) transition which can be used from DC to 110 GHz is presented. The proposed transition connects CPW with CPS by the reformed air-bridge. Two ground planes of CPW are tied at their ends by a line and the centre of the line is connected to the ground strip of CPS by another line. Owing to the symmetry of the proposed structure, the currents of two ground planes of CPW are combined with the same phase and transferred to the ground strip of CPS. With height of 3 μm, the signal line of CPW passes over two connecting lines and is connected to the signal strip of CPS. For the back-to-back transition structure, insertion loss <1 dB and return loss >15 dB are obtained from 0.5 to 110 GHz     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002     

The prospects of non-volatile phase-change RAM

Phase-change read-and-write memory (PRAM) is a promising memory that can solve the problems of conventional memory—scalability, read/write speed, and reliability. We will review the opportunities and technical challenges of PRAM. The most important challenge of PRAM is the reduction of the writing current. Various approaches to reduce the writing current will be reviewed and the prospects of PRAM are discussed.     

The most frequently prescribed medications in the elderly and their impact on dental treatment

The high prevalence of multiple chronic medical conditions in the elderly and the likelihood of multiple drug therapies dramatically increase the chance of drug-specific adverse effects and drug-drug interactions. This article reviews the age-associated alterations in pharmacokinetics and pharmacodynamics along with the most frequently prescribed medications for the elderly. Adverse drug reactions, drug-drug interactions and oral side effects are reviewed along with the impact these medications may have on dental treatment planning and management.     

Computer modeling of the continuous annealing furnace

A computer program to calculate the strip temperature heated in the continuous annealing furnace was developed, using the zone method for radiative heat transfer analysis with the measured gas temperature in the furnace. Using theF _E Operator, the present study considered the effects of soot and transient species, in addition to the H₂O−CO₂ gas mixture on the gas radiative heat transfer. The predicted strip temperature distribution forF _E=1.05 represented well the measured data. The maximum difference in the heat flux transfered to the strip from the combustion gas forF _E=1.0 (without soot and transient species gas radiation) and 1.05 (with soot and transient species gas radiation) was about 15%. The present study also investigated the effects of line speed and thickness variations on the strip temperature, establishing the bases for the on-line computer model.     

Feature selection techniques and comparative studies for large-scale manufacturing processes

In order to efficiently and effectively control an overall process in the process industry, a few important parameters should be identified from high-dimensional, non-linear, and correlated data. Feature selection techniques can be employed to extract a subset of process parameters relevant to product quality. The performance of these techniques depends on the precision of the prediction model formulated to quantify the relationship between the process parameters and the quality characteristics. Although the neural network-based partial least squares (NNPLS) method has been proven to be effective in prediction models for the aforementioned industrial process data, feature selection techniques appropriate for NNPLS models have yet to appear. Here, several techniques for scoring the relevance of process parameters to product quality are proposed and validated by applying three datasets. These experiments show that the proposed techniques can discriminate relevant process parameters from irrelevant ones.     

Effects of potential and heat treatment on phase transition of alumina dielectric layer

The characteristics and growth behaviors of alumina dielectric layer formed by anodic oxidation were investigated. The aluminum oxide layer anodized at 400 V was predominantly amorphous alumina, but at the applied potentials more than 500 V, amorphous and crystalline γ-alumina were existed in anodic oxide layer and the ratio of γ-alumina increased with the increasing applied potential. During the heat treatment at 600^°C or higher temperature, amorphous alumina layer was transformed into the crystalline γ-alumina. The phase transition of anodic amorphous alumina into crystalline depends on anodic applied potentials and heat-treatment temperatures.