Combination of heat treatment and chitosan coating to improve postharvest quality of wolfberry (Lycium barbarum)

The synergistic application of hot water dip at 42 °C for 30 min and 1% chitosan coating on differentiation in postharvest quality traits, microstructure as well as microbiological evolution of wolfberry fruits was investigated. Fresh wolfberry fruits were stored at 2 ± 0.5 °C and 90% relative humidity (RH) for 28 days. Results indicated the combination of prestorage heat treatment and chitosan coating maintained higher levels of ascorbic acid, total phenolic contents and antioxidant capacity as well as lower decay, compared with untreated wolfberry fruits. The possible mechanism was that the heat treatment almost sealed open stomata to limit the sites of pathogen penetration into fruits independently, followed by the biofilm formed by chitosan which controlled secondary infections as well as slowed changes in fruit respiration and metabolic activity in wolfberries. The synergistically treated fruit also exhibited a higher acceptability obtained by sensory analysis after cold storage. In this sense, the integrated application of heat treatment and chitosan coating could be regarded as an effective strategy to extend storage life and maintain the postharvest quality of wolfberry fruits.     

Cerebral microbleeds and cognitive decline in a hemodialysis patient: Case report and review of literature

Cerebral microbleeds (CMBs) are small hemosiderin deposits indicative of prior cerebral microscopic hemorrhage and previously thought to be clinically silent. Recent population‐based cross‐sectional studies and prospective longitudinal cohort studies have revealed association between CMB and cognitive dysfunction. In the general population, CMBs are associated with age, hypertension, and cerebral amyloid angiopathy. In the chronic kidney disease (CKD) population, diminished estimated glomerular filtration rate has been found to be an independent risk factor for CMB, raising the possibility that a uremic milieu may predispose to microbleeds. In the end‐stage renal disease (ESRD) population on hemodialysis, the incidence of microbleeds is significantly higher compared with a control group without history of CKD or stroke. We present an ESRD patient on chronic hemodialysis with a history of gradual cognitive decline and progressive CMBs. Through this case and literature review, we illustrate the need to develop detection and prediction models to treat this frequent development in ESRD patients.     

综合运维软件在供水企业中的应用

文章简述了IT运维的发展趋势,举例说明了综合运维软件的功能特点,并阐述了综合运维软件在供水企业中的应用案例及应用效果,由此提出综合运维软件的重要作用。     

HP295中间裂纹产生机理分析及控制措施

通过对HP295封头冲压开裂件缺陷光电镜分析,查找到缺陷产生部位及其导致原因。对多组铸坯低倍样检查,发现中间裂纹是缺陷根源。此后,根据现场生产情况,分析钢中磷、硫含量、钢水过热度、铸机设备精度、拉速和二次冷却强度等因素对铸坯中间裂纹的影响。通过降低磷、硫,控制过热度,调整设备精度,降低拉速以及优化二次冷却等措施,HP295铸坯中间裂纹得到有效控制,用户加工开裂现象完全杜绝。     

聚氨酯分散剂在液体靛蓝制备中的应用

采用异佛尔酮二异氰酸酯(IPDI)、聚乙二醇200、400、600、800(PEG200、PEG400、PEG600、PEG800)、2,2-二羟甲基丙酸(DMPA)、1-苯基-1,2-乙二醇、中和剂三乙胺(TEA)、甲乙酮肟等为原料,制备了一种阴离子聚氨酯分散剂.通过FTIR、GPC、TG表征了分散剂的结构与性能.利用自制的分散剂采用研磨法制备了液体靛蓝分散液,以液体靛蓝分散液粒径、离心稳定性、储存稳定性为指标,探讨了分散剂链长、用量对分散液性能的影响.结果表明,研磨1 h后,以PEG400为软段合成的聚氨酯分散剂用量为染料质量的60％时制备的液体靛蓝粒径为277.1 nm,1000 r/min离心稳定性达到93.98％,3000 r/min离心稳定性为51.13％,常温放置7 d后粒径变化在20 nm以内,染色后织物的颜色深度(K/S)为10左右,约是粉状靛蓝染色K/S的2倍,染色织物的颜色性能并未改变,SEM显示分散体颗粒大小分布均匀,与分散剂甲基萘磺酸钠的甲醛缩合物(MF)和木质素85A相比,其分散体系稳定性差别不大.     

Decorative near-infrared transmission filters featuring high-efficiency and angular-insensitivity employing 1D photonic crystals

We present a new scheme for visibly-opaque but near-infrared-transmitting filters involving 7 layers based on one-dimensional ternary photonic crystals, with capabilities in reaching nearly 100% transmission efficiency in the near-infrared region. Different decorative reflection colors can be created by adding additional three layers while maintaining the near-infrared transmission performance. In addition, our proposed structural colors show great angular insensitivity up to ±60° for both transverse electric and transverse magnetic polarizations, which are highly desired in various fields. The facile strategy described here involves a simple deposition method for the fabrication, thereby having great potential in diverse applications such as image sensors, anti-counterfeit tag, and optical measurement systems.