Investigation of texture effect on visual colour difference evaluation

The texture effect on visual colour difference evaluation was investigated in this study. Five colour centers were selected and textured colour pairs were generated using scanned textile woven fabrics and colour‐mapping technique. The textured and solid colour pairs were then displayed on a characterized cathode ray tube (CRT) monitor for colour difference evaluation. The colour difference values for the pairs with texture patterns are equal to 5.0 CIELAB units in lightness direction. The texture level was represented by the half‐width of histogram, which is called texture strength in this study. High correlation was found between texture strength and visual colour difference for textured colour pairs, which indicates that an increasing of 10 units of texture strength in luminance would cause a decreasing of 0.25 units visual difference for the five colour centers. The ratio of visual difference between textured and solid colour pairs also indicates a high parametric effect of texture. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 341–347, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Formation of C4 species in the deactivation of a Pd/SiO2 catalyst during the selective hydrogenation of acetylene

The deactivation characteristics of Pd/SiO₂ in the selective hydrogenation of acetylene were correlated with changes in the amount of the C4 species produced. The amounts of butenes produced changed in parallel with the catalyst activity, indicating that the rate limiting step for butene production was the same as that for acetylene hydrogenation. On the other hand, the amount of 1,3-butadiene produced changed, showing a maximum with catalyst deactivation because 1,3-butadiene is an intermediate in the sequential reaction process which involves both the production and consumption of 1,3-butadiene. This was verified by a simultaneous TG/reaction experiment showing that 1,3-butadiene was a precursor of green oil. The catalyst showed a self-regenerative behavior in its activity and the amounts of C4 species produced during the early stage of deactivation because two opposite factors, which contributed to either the lowering or the promotion of activity, were involved in the process. A specific type of polymer species, produced during the initial period of deactivation, is proposed to be responsible for the promotion of catalyst activity.     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

A Subcarriers Allocation Scheme for Cognitive Radio Systems Based on Multi-Carrier Modulation

Cognitive radio (CR) is a dynamic spectrum access technology as a solution to spectrum under-utilization problem in some licensed bands. Operating over an exceedingly wide spectrum, CR systems usually adopt multi-carrier modulation (MCM) to implement flexible channelization. Consequently, efficient channel allocation scheme becomes extremely important to an MCM based CR (MCM-CR) system. In this paper, a maximum likelihood detection model is developed to detect the presence and locations of licensed users (LUs) signals in the frequency domain. Performance of the detection model, including the optimal detection region, detection probability and false alarm probability, is analyzed. A one-order two-state Markovian chain model is proposed to predict channel status information. In particular, a novel subcarrier allocation scheme for MCM-CR systems is proposed, taking into account the confidence of channel estimation, quality of services (QoS) of rental users (RUs) and throughput. To validate the analytical results, simulations have been conducted to show effectiveness of the proposed scheme.     

大型电除尘器的设计、安装及操作要点

探讨了硫酸生产用大型电除尘器的要求、设计参数的选择及结构设计.指出要重视大型电除尘器的设计、制造和安装质量,并精心操作和维护,以实现长周期稳定运行.生产实践表明,只有在各个环节都做到精益求精,才能使国产大型电除尘器的质量和性能尽快达到当今世界先进水平.     

变频液压泵控压力流量控制开环实验及其结果分析

该文首先分析了变频液压泵控调速调压实验控制系统的理论基础,从理论上分析加阻尼后系统开环时恒流的可行性;并付诸实验研究;然后结合实验曲线进行分析,阐明其控制性能优劣.     

I-DEAS软件在轮毂有限元分析中的应用

优化了铝合金轮毂的开发流程.采用I-DEAS软件对铝合金轮毂的弯曲疲劳、径向疲劳及冲击试验进行有限元分析,证明仿真分析可以满足指导车轮设计,优化车轮结构的要求.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

A Microfluidic Device to Acquire Gaseous Samples Via Surface Tension Held Gas-Liquid Interface

We present a relatively simple and effective method for acquiring gaseous samples into microfluidic channels. Hydrophobic polymers are photopatterned on hydrophilic substrates. Due to surface tension, aqueous liquid is confined by the hydrophobic polymers, but not completely blocked by a physical wall, thus allowing an interface for gas-liquid interaction. Here, the mechanism is demonstrated by using hydrophobic (poly)iso-bornyl acrylate polymer patterns on hydrophilic glass substrates, and through a Nessler's reagent-ammonia reaction that exhibits changes in color and electrical resistance.