Effect of bulk flow pulsations on film cooling with compound angle holes

Experiments are conducted to investigate the effects of bulk flow pulsations on film cooling with compound angle holes. A row of five film cooling holes is considered with orientation angles of 0°, 30°, 60°, and 90° at a fixed inclination angle of 35°. Static pressure pulsations are produced by an array of six rotating shutter blades, which extend across the span of the exit of the wind tunnel test section. The pulsation frequency is fixed at 36 Hz, but changes in the time-averaged blowing ratios of 0.5, 1.0 and 2.0 produce three different coolant Strouhal numbers, 3.6, 1.8 and 0.9, respectively. Detailed film cooled boundary layer temperature distributions are measured by a cold wire and the adiabatic film cooling effectiveness by thermochromic liquid crystal (TLC). The boundary layer temperature surveys show that pulsations induce large disruptions to the boundary layer temperature distribution and the film coverage. As the orientation angle increases, the injectant concentration spreads further into the spanwise direction because of pulsations than the steady case. With pulsations the adiabatic film cooling effectiveness value decreases regardless of the orientation angle. The amount of reduction, however, depends on the orientation angle in such a way that the larger the orientation angle is, the smaller the reduction is.     

Analysis and design of synchronous permanent-magnet planar motors

The force equation of a synchronous permanent-magnet planar motor (SPMPM) was investigated. The flux density distribution of a two-dimensional (2-D) magnet array for a SPMPM was obtained by solving the equations of the scalar magnetic potential. The expressions of the force and back-EMF constant were derived and examined. Using these expressions, the conditions for normal operation of the SPMPM were found and the optimal design was determined in order to maximize the force of the SPMPM.     

Integration of mobile vehicles for automated material handlingusing Profibus and IEEE 802.11 networks

This paper focuses on a method to integrate mobile devices such as a mobile robot, automated guided vehicle, and unmanned container transporter to form an automated material handling system. In this paper, the stationary devices are connected via a Profibus network while the mobile devices are communicating via an IEEE 802.11 wireless LAN. In order to integrate these two networks, a protocol converter is developed on a PC platform that runs two interacting processes with shared internal buffers. The protocol converter performs a role of translator between two different protocols by converting the format of a data frame. In addition to this basic conversion function, the protocol converter has a virtual polling algorithm to reduce the uncertainty involved in accessing the wireless network. Finally, the integrated network. of Profibus and IEEE 802.11 is experimentally evaluated for its data latency and throughput, which shows the feasibility of the Profibus-IEEE 802.11 network for industrial applications involving mobile devices     

NiCuZn铁氧体和银内电极的共烧行为

NiCuZn铁氧体正作为磁介质广泛地应用于低烧多层片式电感，因此有必要对其与银内电极的共烧行为进行研究。该文主要介绍NiCuZn铁氧体／银内电极多层复合体共烧过程中的烧结收缩、界面反应、扩散对介质性能的影响。尖晶石结构中存在相当数量的空位，这为银离子提供了一定的溶解度，因此在共烧过程中银对铁氧体的相组成影响较小。银对铁氧体性能的影响体现在两个方面。一方面是由于银具有相对低的烧结温度，从而在烧结过程中起到助烧剂的作用，促进致密化过程，提高烧结体的密度和磁导率；另一方面，银促使铁氧体中的铜在晶界处析出，导致晶界处应力，使磁导率降低，晶粒生长也被一定程度地抑制。     

Thermomechanical fatigue—damage mechanisms and mechanism-based life prediction methods

An existing extensive database on the isothermal and thermomechanical fatigue behaviour of high-temperature titanium alloy EVII 834 and dispersoid-strengthened aluminum alloy X8019 in SiC particle-reinforced as well as unreinv conditions was used to evaluate both the adaptability of fracture mechanics approaches to TMF and the resulting predictive capabilities of determining material life by crack propagation consideration. Selection of the correct microstructural concepts was emphasised and these concepts were, then adjusted by using data from independent experiments in order to avoid any sort of fitting. It is shown that the cyclic /-integral (δJ_eff concept) is suitable to predict the cyclic lifetime for conditions where the total crack propagation rate is approximately identical to pure fatigue crack growth velocity. In the case that crack propagation is strongly affected by creep, the creep-fatigue damage parameter δ_CF introduced by Riedel can be successfully applied. If environmental effects are very pronounced, the accelerating influence of corrosion on fatigue crack propagation can no longer implicitly be taken into account in the fatigue crack growth law. Instead, a linear combination of the crack growth rate contributions from plain fatigue (determined in vacuum) and from environmental attack is assumed and found to yield a satisfactory prediction, if the relevant corrosion process is taken into account.     

ANALYSIS AND PROCESSING OF LMF－COSTAS STEPPED FREQUENCY RADAR SIGNAL

Linear Modulated Frequency (LMF) Costas Stepped Frequency Radar (SFR) signal is introduced. Its ambiguity function is derived and analyzed in detail and its feasibility is validated in theory. The scheme of the proposed signal processing is also presented. The results of theoretic analysis and simulation show that, by using the proposed signal and increasing the bandwidth of the total stepped frequency, the ambiguity sidelobe is well suppressed and the range-velocity coupling in the stepped frequency radar is also greatly weakened.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

Neue Entwicklungen beim Hohlkatoden‐Gasflusssputtern. New Developments in Hollow Cathode Gas Flow Sputtering

The gas flow sputter technique was invented a few years ago particularly for the inexpensive fabrication of sophisticated ceramic layers. Meanwhile, it has matured and become increasingly powerful. Today it is on the verge of being applied in industrial fabrication processes. The present article gives an overview over the method, its characteristics and the numerous applications.     

Electromagnetic micromirror array with single-crystal silicon mirror plate and aluminum spring

We have designed and fabricated an addressable 4 /spl times/ 4 array of micromirrors capable of providing up to 90/spl deg/ of angular deflection. Each micromirror comprises a single-crystalline silicon mirror plate supported by aluminum springs, which provides an extremely flat reflective surface and a compliant spring material that enables the integration of the device into a limited area without mitigating its performance (i.e., total angular deflection). The device is fabricated using a combination of surface and bulk micromachining processes, such as electroplating, bulk wet etching and XeF/sub 2/ etch processes. Selective actuation is accomplished by the use of an electrostatic clamping force on each mirror plate. A mirror rotation angle of more than 80/spl deg/ can be obtained by applying an external magnetic field, and this angle can be further increased by the use of an electrostatic force. The designed structure can be used in microphotonic applications.