A Linear Cross-Coupled Control System for High-Speed Machining

We present a linear cross-coupled controller to improve highspeed contouring accuracy independently of tracking accuracy in a biaxial machine tool feed drive servomechanism. Unlike conventional cross-coupled controllers, the cross-coupled controller presented here is a linear system, so it is very easy to perform the stability and steady-state error analysis, and to optimise the controller parameters. The proposed controller is evaluated experimentally on a CNC LOM machine and compared to an uncoupled controller and a conventional cross-coupled controller. Controller performance is evaluated for a circular contour at a feedrate of 30 m min _1 . The experimental results show that the proposed controller can greatly reduce the contour error at large feedrates. The linear cross-coupled controller is simple to implement and is practical.     

油田污水中咪唑啉缓蚀剂浓度检测技术研究

研究评价了油田污水中咪唑啉缓蚀剂浓度检测的七种方法 ,其中紫外光分析法和显色反应法适合于低浓度咪唑啉缓蚀剂检测 ,且方法简便、速度快、成本低 ,检测浓度范围 2～ 5 0mg/L。     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

离子交换铒掺杂磷酸盐玻璃波导特性研究

给出有关离子交换铒掺杂磷酸盐玻璃波导的制备以及发光特性的基本结果。用Ag+ Na+ 离子交换在含有适量氧化钠的铒掺杂磷酸盐玻璃上很容易实现低损耗平面波导 ,并且离子交换过程对这种玻璃的光谱特性没有影响。     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

环保型隧道防火涂料的研究

介绍了国内外公路隧道、铁路隧道及地铁火灾情况 ,研制出一种可在潮湿环境中使用、火灾发生时无有害气体产生的环保型隧道防火涂料。涂层厚度 18～2 0 mm,耐火极限达 3小时。为防止涂料加水拌和后沉淀分层 ,增加涂料的和易性 ,研制出一种分散剂。     

Si衬底上Ta-N/Cu薄膜性能研究

对Si衬底上Ta-N/Cu薄膜进行了电学和热学分析，结果发现500℃以下薄膜电随几乎不变，600-690℃下的退火引起的电阻率降低是由于Ta-N电阻的热氧化和Cu熔化扩散引起的，而690℃以上的电阻率增加是由于Cu引线传输能力减弱所致，为0.18μm以下的超大规模集成电路中的Cu引线和电阻薄膜的制作提供了有益的借鉴。     

对编写《水轮机》新教材的建议

提出适应新的中等职业《水轮机》教材和课程教学大纲的修改建议。     

������Ȼ����̽���о����½�չ����չ����

2002年AAPG年会于3月10－13日在美国休斯顿隆重召开。根据会议论文，介绍了国外天然气勘探与研究最新进展及发展趋势，其中包括：生物气、海域及深水区有利含气区带、际上新老气区带等常规天然气，以及煤层气、深盆气、天然气水合物等非常规天然气的最新勘探与研究进展。     

十二酰胺丙基二甲基羟乙基氯化铵与十二烷基硫酸钠水溶液的表面吸附和胶束形成

利用十二酰胺丙基二甲胺和氯乙醇反应 ,合成了十二酰胺丙基二甲基羟乙基氯化铵 (DDHA)阳离子表面活性剂 ,将其与十二烷基硫酸钠 (SDS)以不同摩尔比进行混合 ,测定了混合系统的表面张力 ,计算了单一系统和混合系统的饱和吸附量、分子最小截面积 ,表面层和胶束中 DDHA的摩尔分率及分子间相互作用参数 ,目视观察了混合系统的浑浊情况。结果表明 :在降低γcmc和 cmc方面 ,DDHA SDS混合系统有协同效应 ,表面层和胶束的组成与二组分配比有关 ,但是非对称的 ,等物质的量混合物中 ,DDHA在胶束和表面层中具有较大的摩尔分数。DDHA与 SDS在实验测定的各混合系统中都不出现混浊