靶向壳聚糖基因载体与水溶性量子点的自组装

将透明质酸(HA)接枝到四种不同分子量的壳聚糖(CS)上,获得了靶向壳聚糖基因载体。将CS及接枝CS分别与水溶性量子点(QDs)自组装,研究发现,相对于纯QDs,CS/QDs复合物及接枝CS/QDs复合物的荧光强度均明显增强,荧光发射峰位发生红移。复合物呈核/壳结构,QDs被包裹在核内。和CS/QDs复合物相比,接枝CS/QDs复合物的尺寸更小,分布更为均一。     

利用蓄电池废硫酸和硼泥制备高品质氢氧化镁

利用废铅酸蓄电池中的废硫酸作为浸取剂,对硼泥中的镁进行回收并制备出高品质的氢氧化镁产品。实验得出了酸浸硼泥的最佳工艺条件：酸浸温度为80℃;酸浸时间为30 min;酸用量为硫酸与硼泥质量比为1.2∶1。利用不同金属水解pH的不同,将酸浸过程中从硼泥和废硫酸中引入的杂质依次去除,得到精制硫酸镁溶液。由精制硫酸镁制取氢氧化镁的工艺条件为：常温下,沉淀剂为氨水,反应终点pH为11,反应时间为2 h,反应物在50℃下陈化12 h,过滤、洗涤后105℃烘干。实验考察了不同沉淀剂对氢氧化镁形貌的影响。所得氢氧化镁纯度在97%以上,粒径在0.1～1μm之间,各项指标均优于中国化工行业标准。     

MongoDB在水资源在线监测数据处理中的应用

随着水资源在线监测系统的广泛运用,对海量数据的存储和处理需求日益增长。介绍了MongoDB文档型数据库的功能及其特点,提出了MongoDB在水资源在线监测数据处理时的云存储思路和处理策略,能较好地解决水资源在线监测云数据存储和提取的问题。     

阳宗海流域冬季典型农村污水污染特征及水质评价

为揭示阳宗海流域不同类型农村污水各污染指标的影响因素和分布特征,选取云南省的海晏村(传统型)和大营村(集镇型)的污水进行水样采集,通过方差分析研究其不同污染指标的浓度变化以及不同类型农村污水水质的差异性,并运用主成分分析法对污水进行水质评价。结果表明:阳宗海流域海晏村污水中的TN、COD均明显超过了城镇污水处理厂污染物排放二级标准,大营村的TP、TN、COD均明显超过了二级标准;pH值与氧化还原电位都是农村污水中污染物浓度的重要影响因子;两村的水质具有显著的差异性;传统型农村的水质比集镇型农村的要好,说明对阳宗海流域造成污染风险更大的是集镇型农村污水。     

Dielectric Relaxation of La3+-Modified Bi3TiNbO9 Aurivillius Phase Ceramics

Single Aurivillius phase Bi_{3− x} La _x TiNbO₉ (LBTN- x , x =0.00, 0.50, 0.75, and 1.00) ceramics were prepared by the conventional solid-state reaction method. When x ≤0.50, the ceramics are normal ferroelectrics, while LBTN-0.75 and LBTN-1.00 showed typical relaxor behavior, which could probably be attributed to the disordering induced by the La³⁺ partly substituting for Bi³⁺ in Bi₂O₂ layers. The dielectric relaxation of LBTN-0.75 and LBTN-1.00 were fitted using the Vögel–Fulcher relationship, and the results suggest that both of them are analogous to a spin glass with thermally activated polarization fluctuations above a freezing temperature.     

PMN-PZT压电陶瓷的凝胶注模研究

对三元系PMN—PZT压电陶瓷的凝胶注模成形工艺进行了研究,重点讨论了分散剂加入量、pH值、球磨时间与注模浆料流变之间的关系,当分散剂用量为0 .95 %～1 .0 5 % ,pH值为10 .5～11 .5 ,球磨时间为8h时,可以制备出固相含量为5 5 % ,粘度小于1Pa·s的PMN -PZT压电陶瓷悬浮体。将凝胶注模与传统模压成形工艺制备的样品进行了比较,通过扫描电镜(SEM )显微形貌分析和电学性能测定。结果表明:凝胶注模工艺制备的样品与模压工艺制备的样品相比较,其显微结构均匀致密、晶粒大小与晶界分布均匀,气孔率更小,电学性能更均匀。     

Influence of the synthesis conditions on the curing behavior of phenol–urea–formaldehyde resol resins

The curing behavior of synthesized phenol–urea–formaldehyde (PUF) resol resins with various formaldehyde/urea/phenol ratios was studied with differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The results indicated that the synthesis parameters, including the urea content, formaldehyde/phenol ratio, and pH value, had a combined effect on the curing behavior. The pH value played an important role in affecting the shape of the DSC curing curves, the activation energy, and the reaction rate constant. Depending on the pH value, one or two peaks could appear in the DSC curve. The activation energy was lower when pH was below 11. The reaction rate constant increased with an increase in the pH value at both low and high temperatures. The urea content and formaldehyde/phenol ratio had no significant influence on the activation energy and rate constant. DMA showed that both the gel point and tan δ peak temperature (T_tanδ) had the lowest values in the mid‐pH range for the PUF resins. A different trend was observed for the phenol–formaldehyde resin without the urea component. Instead, the gel point and T_tanδ decreased monotonically with an increase in the pH value. For the PUF resins, a high urea content or a low formaldehyde/phenol ratio resulted in a high gel point. The effect of the urea content on T_tanδ was bigger than that on the gel point because of the reversible reaction associated with the urea component. Too much formaldehyde could lead to more reversible reactions and a higher T_tanδ value. The effects of the synthesis conditions on the rigidity of the cured network were complex for the PUF resins. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1368–1375, 2005     

A high propylene productivity over B2O3/SiO2@honeycomb cordierite catalyst for oxidative dehydrogenation of propane

Boron-based metal-free catalysts for oxidative dehydrogenation of propane (ODHP) have drawn great attention in both academia and industry due to their impressive activity and olefin selectivity. Herein, the SiO₂ and B₂O₃ sequentially coated honeycomb cordierite catalyst is designed by a two-step wash-coat method with different B₂O₃ loadings (0.1%–10%) and calcination temperatures (600, 700, 800 °C). SiO₂ obtained by TEOS hydrolysis acts as a media layer to bridge the cordierite substrate and boron oxide via abundant SiOH groups. The well-developed straight channels of honeycomb cordierite make it possible to carry out the reactor under high gas hourly space velocity (GHSV) and the thin wash-coated B₂O₃ layer can effectively facilitate the pore diffusion on the catalyst. The prepared B₂O₃/SiO₂@HC monolithic catalyst exhibits good catalytic performance at low boron oxide loading and achieves excellent propylene selectivity (86.0%), olefin selectivity (97.6%, propylene and ethylene) and negligible CO₂ (0.1%) at 16.9% propane conversion under high GHSV of 345,600 ml·(g B₂O₃)⁻¹·h⁻¹, leading to a high propylene space time yield of 15.7 g C₃H₆·(g B₂O₃)⁻¹·h⁻¹ by suppressing the overoxidation. The obtained results strongly indicate that the boron-based monolithic catalyst can be properly fabricated to warrant the high activity and high throughput with its high gas/surface ratio and straight channels.     

Synthesis and characterization of copolythiophene

Copolythiophenes (Co‐PTs), poly(3‐hexylthiophene‐co‐3‐thiophene carboxylic acid) (P3HT‐TCa), poly(3‐hexyloxylthiophene‐co‐3‐thiophene carboxylic acid) (P3HOT‐TCa), and poly(3‐phenylthiophene‐co‐3‐thiophene carboxylic acid) (P3PhT‐TCa), were synthesized by chemical oxidized polymerization to investigate the effect of copolymerization on the properties of polythiophenes (PTs). Gel permeation chromatography showed that the molecular weight (MW) of Co‐PT was lower than that of homopolythiophene. Fourier transform infrared (FTIR) spectra indicated that the copolymerization was successful between the monomers. The λ_max of Co‐PTs gave a “blue shift” in ultraviolet‐visible (UV‐VIS) spectra. Photoluminescence (PL) spectra showed that the PL intensity of Co‐PT became weaker than that of homopolythiophene and the disappearance of PL had been observed in P3HOT‐TCa. The thermal stability of Co‐PT was influenced by the carboxyl for its low decomposition temperature. Furthermore, the copolymerization between multi‐wall carbon nanotube containing thiophene ring (MWNT‐Th) and 3‐hexyloxylthiphene could also take place successfully. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

N-甲基乙酰氧基乙酰苯胺的液谱分析

本文研究了高效液相色谱测定N－甲基乙酰氧基乙酰苯胺的方法。采用Hypersil C18柱，以甲醇：水＝60：40（V／V）为流动相。该方法的变异系数为0．43％，回收率为98．9％－100．6％。