环糊精和表面活性剂在室温磷光中的应用

介绍了环糊精和表面活性剂作为有序介质在室温磷光中的研究进展．并对各种方法的特点和应用情况作了简要概括。认为环糊精和表面活性剂混合介质能大大提高发光物质的室温磷光．而且操作简便．应用前景广阔。     

PVC／PU合金的制备与研究

叙述了选择混炼型聚氨酯(PU)与分子量适中的Ⅱ型聚氯乙烯(PVC)树脂制备PVC/PU合金的过程,讨论了PVC/PU共混比、填充剂、硫化体系、共混工艺等因素对PVC/PU合金性能的影响。结果表明:选择PVC/PU=60/40(质量比),硫化剂TD15份,白炭黑30份,混炼温度140—160℃,可制得性能优良的PVC/PU合金。动态力学性能实验显示了PVC/PU合金有较好的相容性。     

半刚性钢-混凝土组合节点受弯承载力的计算

在半刚性钢 -混凝土组合框架中 ,混凝土板中的纵向钢筋增加了节点的强度和刚度 ,但是 ,传统的设计方法往往忽略纵向钢筋的作用而采用简化的计算模型。因此 ,出于经济效益考虑 ,应该根据半刚性组合节点的实际受力性能建立更加准确的计算方法。这里详细介绍了考虑混凝土板纵向钢筋作用的半刚性组合节点受弯承载力的计算方法 ,计算结果表明 ,建议的公式与试验结果吻合良好 ,可供规范制定和工程应用参考。     

4-(6′甲基苯并噻唑-2′-偶氮)-3,5-二氨基吡唑与钯显色反应的研究和应用

对6种苯并噻唑偶氮吡唑化合物的分析特性进行了探讨,着重研究了4—(6′—甲基苯并噻唑-2′-偶氮)-3,5-二氨基吡唑(MBTAP)与钯离子显色反应的光度性质。在非离子表面活性剂 Brij35存在下与钯离子形成橙红色的配合物。适宜的 pH 值范围为9.0～10.5.配合物的最大吸收波长为510nm,表观摩尔吸光系数为3.01×10~4L·mol~(-1)·cm~(-1)。钯在0～14μg/25mL,范围内服从比尔定律.显色体系可稳定11h。在柠檬酸存在下可消除 Fe~(3+)、Co~(2+)、Cu~(2+)、Ni~(2+)等离子的干扰。     

基于Jpcap的Webmail邮件还原技术

基于Smtp和Pop3的邮件还原技术已经日臻成熟,而由于主要Webmail邮件格式不同,Webmail邮件还原技术一直是难点。通过对主要Webmail的内容格式分析,针对不同网站的Webmail建立相应的还原模块,实现对主要Webmail的内容还原。实验结果验证了该技术的有效性。     

我国重液蜡生产及市场前景

介绍了国内重液蜡生产现状和市场情况 ,阐述了异丙醇 -尿素脱蜡优于分子筛脱蜡工艺的几个特点 ,并介绍了重液蜡在塑料业、洗涤业、皮革业和微生物方面的发展方向。     

骨架材料对全钢载重子午线轮胎性能的影响

讨论骨架材料的规格、结构分布及工艺控制对全钢载重子午线轮胎性能的影响。胎体帘布采用带有外缠丝的 3 + 9+ 15× 0 2 2 + 0 15规格钢丝、胎体帘线密度在 45 0～ 65 0根·m- 1 范围内 (帘线直径大于 1 2mm)以及胎体反包端点在成品外轮廓曲线的第 2或 3条装配线上等措施均有利于保证胎体强度 ;合理设计带束层结构 ,端点与胎侧肩部花纹距离取 10mm左右有利于消除应力过度集中 ;采用钢丝增强带有利于提高胎圈刚性。     

Phase Assemblages of Pr α-sialon Derived from SHS-ed Powders and TEM Study on the Nucleation of Pr α-sialon

The Pr α-sialon powders prepared by self-propagating high-temperature synthesis (SHS), consisting of 55 wt% Pr α-sialon and 45 wt% of β-sialon (abbreviated as α' and β'), were hot-pressed at 1800°C for 1 h. The results showed that Pr α' phase would transfer to β' with the appearance of JEM phase (Pr(Si_{6− z} Al _z )(N_{10− z} O _z )) after sintering, thus resulting in the increase of β' phase to 86 wt%. The addition of Y₂O₃ into SHS-ed Pr α' powders as the starting materials restrains the transformation of α' to β' and prevents the formation of JEM phase as well. The nucleation mechanism of Pr α' grain during hot-pressing was investigated in terms of transmission electron microscope and energy-dispersive spectrometer analysis. Two nucleation modes of Pr α' grains were found, i.e., nucleating on the undissolved Pr α' grains and on the nuclei of (Pr, Y) α' grains precipitated from liquid phase.     

Ink‐eliminated waste paper sludge flour‐filled polypropylene composites with different coupling agent treatments

Ink‐eliminated sludge flour (IESF), waste residue from the recycling treatments of waste paper, was utilized as a new kind of filler to reinforce polypropylene (PP) in this research work. Different coupling agents, including maleated anhydride grafted PP (MAPP), stearic acid (SA), and titanate (NDZ‐101), were used to increase the compatibility between IESF and PP. By using different measurements, the microstructure, morphology, thermal behaviors, and mechanical properties of the IESF/PP composites were investigated in detail. It was found that IESF, as a nucleation agent, not only induced the crystallization orientation of PP but also accelerate the crystallization rate of PP. Just as indicated in the experiments, the presence of IESF has shown the advantages of increasing the dimensional stability, the hardness and the flexural property, and the presence of coupling agents has a favorable effect on the improvement of dimensional stability. Moreover, the coupling agent has minor influence on the mechanical property, even causes some decrease in the impact strength. Among these three coupling agents, MAPP is found to be the best coupling agent for increasing the interfacial adhesion between IESF and PP, and the MAPP addition makes the PP composite possess the quickest crystallization rate and greatest tensile strength. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 513–520, 2003     

粉末材料合成金刚石中工艺参数的选取

合理地选取工艺参数,有利于合成优质金刚石.文章综述了粉末材料合成金刚石中工艺参数对合成效果的影响以及粉末材料合成金刚石中工艺参数的选取原则.