Experimental investigations of machining characteristics and removal mechanisms of advanced ceramics in high speed deep grinding

Machining characteristics and surface integrity of advanced ceramics, including alumina, alumina–titania, and yttria partially stabilized tetragonal zirconia, were studied under high speed deep grinding conditions. Material removal mechanisms involved in the grinding processes were explored. The material removal in the grinding of alumina and alumina–titania was dominated by grain dislodgement or lateral cracking along grain boundaries. The removal for zirconia was via both local micro fracture and ductile cutting. It was found that under a feed rate of 500 mm/min and for all the wheel speeds used, an increase in the wheel depth of cut (DOC) from 0.1–2 mm slightly improved the ground surface finish, but greatly prolonged the wheel life. This increase did not deepen the subsurface damage layer for the alumina and alumina–titania, but resulted in a slightly deeper damage layer for the zirconia.     

20G高压锅炉管裂纹原因分析

对20G高压锅炉管产生裂纹的原因进行了分析，结果表明是冷拔工艺不当所致。     

如何提高模具质量

介绍了提高模具质量的基本途径，分析了模具的正确使用与维护对其寿命的影响。     

第62届世界铸造会议宣读论文综述(有色金属部分)

详细介绍了第 62届世界铸造会议中有关有色合金铸造的 6篇宣读论文。“铝合金压铸的压力传递与铸件质量的关系”一文提出一种新的测量铝合金压铸型腔中压力传递的方法 ,搞清了压力传递、流速与铸件质量之间的关系 ,获得了本届会议的优秀论文奖。“挤压压铸和半固态铸造生产高质量、复杂的铸件”一文展示了应用压铸高技术 ,生产出力学性能极高的汽车用复杂压铸件。“监控金属型、压铸模温度的智能系统”一文提出的智能控温系统 ,测温可靠 ,能自动控制铸型温度 ,铸型中不需开冷却水孔道。“制造金属基复合材料的复合铸造工艺 (Hybrid)”一文介绍了一种挤压铸造和熔模铸造相结合生产金属基复合材料的新工艺。“喷铸法制取铝基SiCp增强复合材料的微观组织和磨耗特性”一文指出用喷铸法制取的铝基SiCp增强复合材料 ,具有很高的耐磨性能。“不同凝固条件下 ,Na ,Ca含量对加Sb变质的 3 5 6合金力学性能的影响”一文的作者通过大量试验 ,搞清了Na ,Ca的有害作用 ,指出 3 5 6合金的σb 与δ之间存在下列关系 :σb(MPa) =2 5 .87lgδ( % ) 12 8.85。     

表面氧化层对TiMn1.25Cr0.25储氢合金活化性能的影响

通过TiMn1.25Cr0.25合金粉活化前在空气中暴露不同的时间,探讨了表面氧化层的形成对其活化性能的影响。活化测试结果表明：合金的活化难度随着合金在空气中暴露时间的延长而加大。俄歇电子能谱(AES)结果表明,在空气中暴露后的合金表面形成了一层大约6nm-10nm厚的表面氧化层,正是这层氧化层的形成加大了合金的活化难度。扫描电镜(SEM)结果表明合金的活化过程与合金的碎化有着密切的联系。     

激光快速成形Rene′88DT高温合金的时效强化研究

研究了时效时间对激光快速成形后时效硬化镍基高温合金Rene′88DT中沉淀相组织演化和力学性能的影响。发现随时效时间的增加，沉淀相y’略有长大，颗粒之间发生大颗粒吞噬小颗粒的粗化，时效40h后沉淀相颗粒粗化明显。对经不同时间时效后的激光快速成形Rene′88DT试样进行了硬度测试。结果显示，在时效时间为28h时，硬度有一峰值HRC49。在此基础上，采用1165℃，2h固溶、空冷＋760℃，28h时效的热处理工艺对激光快速成形标准拉伸棒样进行了热处理，拉伸结果显示成形件的抗拉强度较激光沉积态提高了400MPa，屈服强度接近同种材料的粉末锻造水平。     

Multifocus image fusion method of Ripplet transform based on cycle spinning

The curvelet transform can represent images at both different scales and different directions. Ripplet transform, as a higher dimensional generalization of the curvelet transform, provides a new tight frame with sparse representation for images with discontinuities along C² curves. However, the ripplet transform is lack of translation invariance, which causes the pseudo-Gibbs phenomenon on the edges of image. In this paper, the cycle spinning method is adopted to suppress the pseudo-Gibbs phenomena in the multifocus image fusion. On the other hand, a modified sum-modified-laplacian rule based on the threshold is proposed to make the decision map to select the ripplet coefficient. Several experiments are executed to compare the presented approach with other methods based on the curvelet, sharp frequency localized contourlet transform and shearlet transform. The experiments demonstrate that the presented fusion algorithm outperforms these image fusion works.     

Leader-following consensus for uncertain second-order nonlinear multi-agent systems

This paper studies the leader-following consensus problem for a class of second-order nonlinear multi-agent systems subject to linearly parameterized uncertainty and disturbance. The problem is solved by integrating the adaptive control technique and the adaptive distributed observer method. The design procedure is illustrated by an example with a group of Van der Pol oscillators as the followers and a harmonic system as the leader.