Synthesis and electrical properties of poly[2-(2-(4-trifluoromethyl)phenyl)ethenyl-1,4-phenylenevinylene] and PPV copolymers

Summary Poly[2-(2-(4-(trifluoromethyl)phenyl)ethenyl)-5-methoxy-1,4-phenylenevinylene] (PFEMPV) and a series of PPV copolymers containing 1,4-phenylenevinylene (PV) units were synthesized through a water-soluble precursor route, and their electrical and third-order nonlinear optical properties were studied. The PFEMPV films could not be doped with I₂, but FeCl₃-doped films showed an electrical conductivity of 5.0x10^-4 S/cm. The conductivities of FeCl₃-doped copolymer films ranged from 2.0x10^-3 to 2.0 S/cm depending on their copolymer compositions. The third-order nonlinear optical susceptibility, ⁽³⁾(–;,,–), was also investigated by the degenerate four wave mixing technique at 602 nm. The ⁽³⁾ value of PFEMPV was 6.9x10^-11 esu. The photoluminescence spectrum of PFEMPV shows its emission maximum at 550 nm.     

Electrical conductivity of polyblends of poly(1,4-phenylene vinylene) and poly(2,5-dimethoxy-1,4-phenylene vinylene)

Summary A series of polyblends of poly(1,4-phenylene vinylene), PPV, and poly(2,5-dimethoxy-1,4-phenylene vinylene), PDMPV, were prepared in film form from precursor polyblends of the respective sulfonium salt polymers, which were separately prepared from the respectivebis(sulfonium salt) monomers. The blend films were doped with I₂ at room temperature to obtain a wide range of electrical conductivities (10^–2 to 10²Scm^–1) depending on the blend composition. The higher the content of PDMPV in the blends the higher was the conductivity.     

Cure kinetics of high performance epoxy resin systems

Summary Isothermal cure kinetics ofEPON HPT 1071/DDS system have been performed by means of differential scanning calorimetry. The maximum cure rate and the extent of conversion at various DDS concentrations were studied as a function of cure temperature. Maximum cure rate increases with increasing cure temperature and DDS concentration. At various DDS concentrations, the maximum cure rate occured between 19–22% conversion. In order to evaluate the kinetic parameters, numerical calculations by means of a Newton-Raphson technique and experimental results obtained from the peak of reaction rate curve were undertaken.     

Improvement of cyclodextrin glucanotransferase as an antistaling enzyme by error-prone PCR

In an effort to improve the properties of cyclodextrin glucanotransferase (CGTase) as an antistaling enzyme, error-prone PCR was used to introduce random mutations into a CGTase cloned from alkalophilic Bacillus sp. I-5 (CGTase I-5). A mutant CGTase[3-18] with the three mutations M234T, F259I and V591A was selected by agar plate assay. Sequence alignment of various CGTases indicated that M234 and F259 are located in the vicinity of the catalytic sites of the enzyme and V591 in the starch binding domain E. The cyclization activity of CGTase[3-18] was dramatically decreased by 10-fold, while the hydrolyzing activity was increased by up to 15-fold. These mutations near subsite +1 (M234T) and at subsite +2 (F259I) are likely to alter the enzyme activity in a concerted manner, promoting hydrolysis of substrate while retarding cyclization. The addition of CGTase[3-18] reduced the retrogradation rate of bread by as much as did the commercial antistaling enzyme Novamyl during 7-day storage at 4 degrees C. No cyclodextrin (CD) was detected in bread treated with CGTase[3-18], whereas 21 mg of CD per 10 g of bread was produced in bread treated with wild-type CGTase.     

Synthesis of liquid crystalline epoxy and its mechanical and electrical characteristics—curing reaction of LCE with diamines by DSC analysis

An aromatic liquid crystalline epoxy monomer based on biphenyl mesogen was synthesized and cured with three different aromatic diamines. The curing reaction characteristics were analyzed by DSC, and the data were introduced to the Kissinger equation to attain the kinetic parameters. Diglycidyl ether of 4,4′‐biphenyl (DGEBP)/4,4′‐diaminobiphenyl (DABP), and DGEBP/4,4′‐methylenediamine (MDA) systems showed an exotherm curing reaction after comelting of the monomers; the DGEBP/p‐phenylenediamine (PDA) system's curing reaction took place in the solid state without melting of monomers. The activation energy and preexponential factor for the DGEBP/DABP system were 55.6 kJ/mol and 4.0 × 10⁶ min^?1, respectively. Those values for DGEBP/MDA and DGEBP/PDA systems were 55.1 kJ/mol and 1.0 × 10⁶ min^?1 and 148.8 kJ/mol and 7.7 × 10¹⁹ min^?1, respectively. The rate constant at 100°C for DGEBP/PDA is 2 times higher than those for DGEBP/DABP and DGEBP/MDA, which have almost the same values. Strictly speaking, the rate constant of DGEBP/DABP is a little higher than that of DGEBP/MDA, and these results are in good agreement with the DSC curves. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2419–2425, 2002     

Preparation and characterization of maleic anhydride‐g‐polypropylene/diamine‐modified clay nanocomposites

Polypropylene (PP)/montmorillonite (MMT) nanocomposites were prepared by compounding maleic anhydride‐g‐polypropylene (MAPP) with MMT modified with α,ω‐diaminododecane. Structural characterization confirmed the formation of characteristic amide linkages and the intercalation of MAPP between the silicate layers. In particular, X‐ray diffraction patterns of the modified clay and MAPP/MMT composites showed 001 basal spacing enlargement as much as 1.49 nm. Thermogravimetric analysis revealed that the thermal decomposition of the composite took place at a slightly higher temperature than that of MAPP. The heat of fusion of the MAPP phase decreased, indicating that the crystallization of MAPP was suppressed by the clay layers. PP/MAPP/MMT composites showed a 20–35% higher tensile modulus and tensile strength compared to those corresponding to PP/MAPP. However, the elongation at break decreased drastically, even when the content of MMT was as low as 1.25–5 wt %. The relatively short chain length and loop structure of MAPP bound to the clay layers made the penetration of MAPP molecules into the PP homopolymer phase implausible and is thought to be responsible for the decreased elongation at break. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 307–311, 2005     

Energetic surface heterogeneity of nanocrystalline TiO<Subscript>2</Subscript> films for dye-sensitized solar cells

Dye sensitized solar cells (DSSCs) have been receiving significant attention because they have many advantages compared to conventional organic solar cells. It has been known that the photovoltaic characteristics of DSSC are highly dependent on the adsorption properties of dyes on TiO₂ films. To analyze the surface heterogeneity of TiO₂ surfaces, single-phase anatase nanocrystallite titanium films were prepared by sol-gel method using the hydrolysis reaction of titanium tetraisopropoxide under acidic condition and characterized by XRD, FE-SEM and BET analysis. The adsorption energy distribution functions were calculated by the generalized nonlinear regularization method. It was found that the shape and the intensity of the adsorption energy distribution curve determined were highly related with the physical properties (i.e., geometrical heterogeneity) and chemical characteristics (i.e., energetic heterogeneity) of nanocrystalline TiO₂ for DSSC.     

Modeling and economic analysis of CO<Subscript>2</Subscript> separation process with hollow fiber membrane modules

The main purpose of the study was to develop a model using ASPEN and Excel simulation method to establish optimum CO₂ separation process utilizing hollow fiber membrane modules to treat exhaust gas from LNG combustion. During the simulation, optimum conditions of each CO₂ separation scenario were determined while operating parameters of CO₂ separation process were varied. The characteristics of hollow fibers membrane were assigned as 60 GPU of permeability and 25 of selectivity for the simulation. The simulation results illustrated that 4 stage connection of membrane module is required in order to achieve over 99% of CO₂ purity and 90% of recovery rate. The resulted optimum design and operation parameters throughout the simulation were also correlated with the experimental data from the actual CO₂ separation facility which has a capacity of 1,000 Nm³/day located in the Korea Research Institute of Chemical Technology. Throughout the simulation, the operating parameters of minimum energy consumption were evaluated. Economic analysis of pilot scale of CO₂ separation plant was done with the comparison of energy cost of CO₂ recovery and equipment cost of the plant based on the simulation model. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Interfacial reaction in ASZ/A384 Al composite and its influence on mechanical properties

In an ASZ/A384 Al composite, the interfacial reaction was observed to take place between the SiO₂ binder layer and Mg within the matrix to form MgAl₂O₄ at the interface. Formation of MgAl₂O₄ at the interface between ASZ short fibers and the Al matrix alloy is believed to enhance the interfacial bonding strength, resulting in improved composite strength. However, the interfacial reaction in the ASZ/A384 Al proceeds at the expense of Mg in the matrix, resulting in a composite devoid of Mg bearing precipitates such as Al₂CuMg and Mg₂Si.     

Effects of Rare Earth Metal addition on the cavitation erosion-corrosion resistance of super duplex stainless steels

Austenitic stainless steels such as AISI 316L have been used in equipment in which fluid flows at high speeds which can induce cavitation erosion on metallic surfaces due to the collapse of cavities, where the collapse is caused by the sudden change of local pressure within the liquid. Usually AISI 316L is susceptible to cavitation erosion. This research focuses on developing a better material to replace the AISI 316L used in equipment with high speed fluid flow, such as impellers. The effects of Rare Earth Metal (REM) additions on the cavitation erosion-corrosion resistance of duplex stainless steels were studied using metallographic examination, the potentiodynamic anodic polarization test, the tensile test, the X-ray diffraction test and the ultrasonic cavitation erosion test. The experimental alloys were found to have superior mechanical properties due to interstitial solid solution strengthening, by adding high nitrogen (0.4%), as well as by the refinement of phases and grains induced by fine REM oxides and oxy-sulfides. Corrosion resistance decreases in a gentle gradient as the REM content increases. However, REM containing alloys show superior corrosion resistance compared with that of other commercial alloys (SAF 2507, AISI 316L). Owing to their excellent mechanical properties and corrosion resistance, the alloys containing REM have high cavitation erosion-corrosion resistance.