Identification of vivianite,an unusual blue pigment,in a sixteenth century painting and its implications

Vivianite, a blue pigment employed in the past practically only in Northern and Central Europe, but with very limited use, was identified in an early sixteenth century painting, stylistically with Flemish features, from a church in Portugal. The identification of this iron phosphate mineral was made by SEM‐EDS based on the atomic ratio between phosphorus and iron in layers of blue paint (area analysis) and in particles of these same layers (spot analysis). This painting, about which there is no document to prove its authorship, becomes the first case, known in detail, of a sixteenth century painting containing vivianite. Moreover, this find and the presence of a chalk ground, also identified, strongly support the hypothesis of being a Flemish painting.     

Smart TDI readout circuit for long-wavelength IR detector

A smart time delay and integration (TDI) readout circuit is suggested which performs background suppression, cell-to-cell non-uniformity compensation, and dead pixel correction. Using the smart TDI readout circuit, the integration capacitor area occupying almost the whole area of a unit-cell can be reduced to one-fifth and transimpedance gain can increase by five times. From measurement results, it is found that the skimming current error for a few hundred nA background current is < 1.25 nA corresponding to LSB/2 of ADC and the non-uniformity introduced by cell-to-cell background current variation is reduced to 1.02 nA     

Clarification of a wheat straw‐derived medium with ion‐exchange resins for xylitol crystallization

BACKGROUND: Xylitol bioproduction from lignocellulosic residues comprises hydrolysis of the hemicellulose, detoxification of the hydrolysate, bioconversion of the xylose, and recovery of xylitol from the fermented hydrolysate. There are relatively few reports on xylitol recovery from fermented media. In the present study, ion‐exchange resins were used to clarify a fermented wheat straw hemicellulosic hydrolysate, which was then vacuum‐concentrated and submitted to cooling in the presence of ethanol for xylitol crystallization. RESULTS: Sequential adsorption into two anion‐exchange resins (A‐860S and A‐500PS) promoted considerable reductions in the content of soluble by‐products (up to 97.5%) and in medium coloration (99.5%). Vacuum concentration led to a dark‐colored viscous solution that inhibited xylitol crystallization. This inhibition could be overcome by mixing the concentrated medium with a commercial xylitol solution. Such a strategy led to xylitol crystals with up to 95.9% purity. The crystallization yield (43.5%) was close to that observed when using commercial xylitol solution (51.4%). CONCLUSION: The experimental data demonstrate the feasibility of using ion‐exchange resins followed by cooling in the presence of ethanol as a strategy to promote the fast recovery and purification of xylitol from hemicellulose‐derived fermentation media. Copyright © 2008 Society of Chemical Industry     

The effect of CaF<Subscript>2</Subscript> on thermodynamics of CaO-CaF<Subscript>2</Subscript>-SiO<Subscript>2</Subscript>(-MgO) slags

To address the role of CaF₂ in the CaO-CaF₂-SiO₂(-MgO) slag system employed for the production of low-pressure rotor steels, the thermodynamic aspects of the slag were investigated by equilibrating it with liquid iron at 1873 K in CaO or MgO crucibles. Presaturation of slag with an oxide block piece of CaO or MgO in a Pt crucible and application of a carbon paste to the outside of an oxide crucible were designed to prevent crucible failure during the slag-metal experiments. The liquidus isotherm and phase boundary of the preceding slag system were investigated using the slag-metal equilibria. Also, the effect of CaF₂ on the sulfide capacity and the activity coefficient of Fe _t O were of particular interest in controlling the sulfur level and cleanliness of low-pressure rotor steels.     

Effect of the pressure drop rate on cell nucleation in continuous processing of microcellular polymers

Microllular plastics are cellular polymers characterized by cell densities greater than 10⁹ cells/cm³ and cells smaller than 10 μm. One of the critical steps in the continuous production of microcellular plastics is the promotion of high cell nucleation rates in a flowing polymer matrix. These high nucleation rates can be achieved by first forming a polymer/gas solution followed by rapidly decreasing the solubility of gas in the polymer. Since, in the processing range of interest, the gas solubility in the polymer decreases as the pressure decreases, a rapid pressure drop element, consisting of a nozzle, has been employed as a continuous microcellular nucleation device. In this paper, the effects of the pressure drop rate on the nucleation of cells and the cell density are discussed. The experimental results indicate that both the magnitude and the cell density are discussed. The experimental results indicate that both the magnitude and the rate of pressure drop play a strong role in microcellular processing. The pressure phenomenon affects the thermodynamic instability induced in the polymer/gas solution and the competition between cell nucleation and growth.