Shift in thinking to address the 21st century hunger gap

The present water policy debate is dominated by the 30 yr old mission to secure water supply and sanitation to all people. The water needed to produce a nutritionally acceptable diet for one person is however 70 times as large as the amount needed for domestic water supply. The food security dilemma is largest in arid climate regions, a situation constituting a formidable challenge. It is suggested that an additional 5 600 km³/yr of consumptive water use will be needed to produce an adequate amount of food by 2050 – i.e almost a doubling of today’s consumptive use of 6800 km³/yr. Past misinterpretations and conceptual deficiencies show the importance of a shift in thinking. Combining the scale of the challenge and the time scale of the efforts to feed humanity and eradicate hunger leads to an impression of great urgency. This urgency strengthens the call for international research both for supporting agricultural upgrading, and for much better handling of issues of environmental sustainability. What stands out is the need of a new generation of water professionals, able to handle complexity and able to incorporate water implications of land use and of ecosystem health in integrated water resources management. It will for those reasons be essential and urgent to upgrade the educational system to producing this new generation.     

Application of Code Approach for Emergency Evacuation in a Rail Station

This paper presents an emergency evacuation analysis during a mid-platform train fire in an underground rail station. A time-based evacuation scenario is developed taking into account the stairway inaccessibility due to smoke blockage. The calculation approach in NFPA 130 is then applied to a parametric study of this time-based scenario and its reliability is examined using a micro-simulation model. Both methods give consistent predictions of the exiting times. The results demonstrate that with the division of the station into two zones, the exiting time could not meet the code requirements, whereas it does meet the required exiting time without the division. Such division is due to smoke blockage and creates an uneven ratio of the occupant load to the available exiting capacity. This shows that appropriate consideration of the fire and smoke effects is important for station egress evaluation. Other issues such as the fire growth rate and the pre-evacuation time are also discussed.     

Development of Low-Oxide MCrAlY Coatings for Gas Turbine Applications

Advanced high-energy plasma systems are being used to achieve the benefits of the high-velocity oxy-fuel (HVOF) system without losing the inherent advantages of plasma for coating of gas turbine parts. MCrAlY coatings play a very important role in the performance and reliability of gas turbine components. One of the important considerations for next generation of gas turbines, which have more demanding conditions and need to withstand ever increasing operating temperatures, is that they should possess very low oxygen content levels in the coating. Low oxygen content coatings are applied by the expensive low-pressure plasma spray (LPPS)/vacuum plasma spray (VPS) technique for critical components in aero- and land-based gas turbines. This work deals with the development of low-cost LPPS equivalent coatings (having low oxygen content) using the high-energy high-velocity plasma spray (HEHVPS) gun and inert gas shroud. A comparison has also been made with CoNiCrAlY coatings by HVOF.     

Damaged layer characteristics in micro-endmilling of copper using an ultrahigh-speed air spindle

This paper presents an investigation on the characteristics of damaged layer in micro-machining by using the ultrahigh-speed air spindle. The damaged layer in metal cutting is derived from plastic deformation and transformation of metal structure. In this study, micro-cutting force, surface roughness, and plastic deformation layer according to the variation of machining conditions were investigated by experiments. The damaged layer was measured using optical microscope for the samples prepared by metallographic techniques. Its scale was dependent on cutting process parameters, especially feed per tooth. According to experimental results, it was verified that the thickness of damaged layer was increased with increasing of feed per tooth and cutting depth, also thickness of damaged layer was reduced in down-milling compared to upmilling during micro-endmilling operation.     

Residual Stress Simulation of Injection Molding

In this study, distribution and history of residual stresses in plaque-like geometries are simulated based on linear thermoviscoelastic model, which helps to understand the mechanics and evolution of the residual stresses in the injection molding process. The numerical calculation of direction, combined with the specified boundary conditions. Results show that the stress variation across the thickness exhibits a high surface tensile value changing to a compressive peak value close to the surface, with the core region experiencing a parabolic tensile peak. Residual stress distribution throughout the thickness is almost same along the flowpath and the final residual stresses value near the gate is lower than the value near the end of flowpath.     

Theoretical Investigation of Time Suboptimal Control of Industrial Manipulators Along Specified Paths

A method for the time suboptimal control of an industrial manipulator from an initial position and orientation to a final position and orientation as it moves along a specified path is proposed. Nonlinear system equations that describe the manipulator motion are linearized at each time step along the path. A method which gives the control inputs (joint angular velocities) for time suboptimal control of the manipulator is developed. In the formulation, joint angular velocity and acceleration limitations are also taken into consideration. A six degree of freedom elbow type manipulator is used in numerical examples to verify the method developed.     

Evaluating non-business e-commerce adoption decision processes and gender roles

Non-business e-commerce adoption refers to the use of e-commerce by not-for profit organizations such as religious organizations, government agencies and academic institutions to reduce their expenses or to improve their operations and customer service. Being a new research niche in the field of e-commerce, non-business e-commerce has received very little or no research attention. This has resulted in a very poor understanding of this niche, especially with regards to its adoption facilitators and inhibitors. Based on this impetus, a field survey of Malaysian Universities was conducted to determine the key factors that facilitate non-business EC adoption as well as the role of gender differential. A comprehensive list of potential facilitators for the strategic use of information technology was derived from extant research reports and used to collect data from five public universities in Malaysia. The data were factor-analysed to determine the key underlying dimensions of facilitators. On the basis of the resulting five dimensions namely, relative advantage orientation, network orientation, information efficiency orientation, innovativeness orientation and competitiveness orientation, regression analysis was done to determine the impact of the five dimensions on adoption. Dummy variable was created for gender and applied in the regression analysis in order to estimate the moderation effect of sex typing on the relationship between the resulting dimensions and adoption. Implications of the findings are discussed.     

Mechanical properties of iron processed by severe plastic deformation

In the present study, the mechanical properties of Fe processed via severe plastic deformation (equal-channel angular pressing (ECAP)) at room temperature were investigated for the first time. The grain size of annealed Fe, with an initial grain size of about 200 μm, was reduced drastically during ECAP. After eight passes, the grain size reaches 200 to 400 nm, as documented by means of transmission electron microscopy (TEM). The value of microhardness during pressing increases 3 times over that of the starting material after the first pass and increases slightly during subsequent pressing for higher-purity Fe. Examination of the value of microhardness after eight passes as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization, an observation that resembles the behavior reported for heavily deformed metals and alloys. The tensile and compression behaviors were examined. In tension, a drop in the engineering stress-engineering strain curve beyond maximum load was observed both in the annealed Fe and the ECAP Fe. This drop is related to the neck deformation. The fracture surface, examined by scanning electron microscopy (SEM), shows vein patterns, which is different from the dimples found on the fracture surface of annealed Fe. In compression, an initial strain-hardening region followed by a no-strain-hardening region was observed in the ECAP Fe. The yield strength in tension of the ECAP Fe was observed to be higher than that in compression. The strengthening mechanisms and softening behavior are discussed.