Einfluß der Korngröße auf mechanische Eigenschaften und den ungeschmierten reversierenden Gleitverschleiß von Al2O3-Keramik

Influence of grain size on mechanical properties and dry oscillating sliding wear of Al₂O₃-ceramics Specimens with average grain sizes varying between about 0.8 μm and 12 μm were produced by cold isostatic pressing of high purity Al₂O₃-powder followed by sintering between 1300°C and 1700°C. Hardness, Young's modulus, bending strength and fracture toughness were measured as a function of average grain sizes. Tribological tests were carried out on the different microstructures at normal laboratory air and room temperature by using a ring-on-block tribometer. Experimental results showed the dependence of mechanical properties on grain size, hardness and bending strength obeying a Hall-Petch type relation, approximately. Coefficient of friction was relatively independent of grain size under the test conditions used. However, wear intensity increased substantially if a critical grain size was surpassed. This was due to a change in mechanisms of material removal which was confirmed by scanning electron microscopical studies of the worn surfaces.     

On detecting the presence of fetal R-wave using the moving averagedmagnitude difference algorithm

An efficient algorithm detecting the presence of a fetal QRS complex is presented. The proposed fetal QRS detection method computes the averaged magnitude of the difference between the fetal ECG signal and the reference signal to detect the fetal QRS event. The detected fetal QRS complexes are exponentially averaged to generate the template signal which can track the slowly varying shape of the fetal ECG signal. As an effort to obtain improved detection performances, two approaches of normalizing the fetal ECG signal and the template are considered.     

Aerodynamic effect on natural frequency and flutter instability in rotating optical disks

 Experimental studies on the aerodynamic coupling effect on natural frequencies and flutter instability of rotating disks are investigated in this paper. The experiments performed using a vacuum chamber and optical disks give two main results. One is that the aerodynamic effect by surrounding air reduces the natural frequencies and critical speeds of the vibration modes in pre-flutter regions. The other is that the natural frequency of the disk rotating at ambient atmospheric pressure is equal to that in vacuum at the flutter onset speed where the disk experiences aero-induced flutter. In post-flutter regions, the aerodynamic coupling between the disk and surrounding air increases the natural frequencies of the disk. Received: 17 June 2002/Accepted: 7 October 2002 The work was supported by Grant No. R11-1997-042-090001-0 of the Center for Information Storage Devices designated by the Korea Science & Engineering Foundation. Paper presented at the 13th Annual Symposium on Information Storage and Processing Systems, Santa Clara, CA, USA, 17–18 June, 2002     

The design of experiments when there are errors in all the variables

The Error-in-Variables Model (EVM) applies to a large class of problems in parameter estimation in which there is error in all the variables. This property makes it of more general applicability than the widely used technique of ordinary Least Squares. While there is a voluminous literature on EVM there is nothing on a general method for designing experiments when EVM applies. In this paper we present an extension of the concept of D-optimality to provide such a general method. It is illustrated by applying it to the estimation of copolymer reactivity ratios and to fitting an ellipse.     

Optical measurements of thermal diffusivity of a material

The measurement of thermal diffusivity of a material (in particular, a thin film) is important for various reasons, e.g., to predict the heat transfer in the solid subjected to a thermal process, to monitor surface composition or morphology, or to detect invisible subsurface defects like delaminations. This measurement can be done in a noncontact manner using various photothermal methods. Such methods typically involve pulsed heating of the surface by small amounts using a laser source; the decay of the surface temperature after this pulsed photothermal heating is then probed to provide the thermal diffusivity. Various probing methods have been developed in the literature, including the probing of reflection, refraction, and diffraction from the pulsed heated area, infrared thermal radiometry, and surface deformation. This paper provides an overview of such techniques and some examples of their applications.     

Contributions of source and inhibitory mechanisms to age-related retroactive interference in verbal working memory.

Determining contributions of source-monitoring and inhibitory function to age-related forgetting has been an elusive goal for cognitive theorists. Five studies used a verbal working memory paradigm to examine mechanisms accounting for disproportionate retroactive interference (RI) experienced with adult aging. Participants distinguished studied target-word pairs from interfering pairs that were read aloud. Source-monitoring and inhibitory task components varied through manipulations of response requirements. RI effects were primarily due to source-monitoring failures rather than to inhibitory failures. Removing both source and inhibitory components eliminated age differences in RI. When source monitoring was emphasized, RI continued to be observed in all age groups but disproportionately for older adults. Process dissociation analyses of memory found recollection decreases and familiarity increases consistent with source failures. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

An efficient assumed strain element model with six DOF per node for geometrically non-linear shells

The present paper describes an assumed strain finite element model with six degrees of freedom per node designed for geometrically non-linear shell analysis. An important feature of the present paper is the discussion on the spurious kinematic modes and the assumed strain field in the geometrically non-linear setting. The kinematics of deformation is described by using vector components in contrast to the conventional formulation which requires the use of trigonometric functions of rotational angles. Accordingly, converged solutions can be obtained for load or displacement increments that are much larger than possible with the conventional formulation with rotational angles. In addition, a detailed study of the spurious kinematic modes and the choice of assumed strain field reveals that the same assumed strain field can be used for both geometrically linear and non-linear cases to alleviate element locking while maintaining kinematic stability. It is strongly recommended that the element models, described in the present paper, be used instead of the conventional shell element models that employ rotational angles.     

Experience with Applying Formal Methods to Protocol Specification and System Architecture

In the last three years or so we at Enterprise Platforms Group at Intel Corporation have been applying formal methods to various problems that arose during the process of defining platform architectures for Intel's processor families. In this paper we give an overview of some of the problems we have worked on, the results we have obtained, and the lessons we have learned. The last topic is addressed mainly from the perspective of platform architects.     

Possibility of sewage and combined sewer overflow reuse with biological aerated filters.

The secondary effluent from municipal plants in Korea generally represents higher BOD with lower SS. Therefore, more soluble forms of organics and NH4-N need to be removed to improve its effluent for reuse. In this study reuse possibility of secondary effluent and CSO (combined sewer overflow) using BAF (biological aerated filter) was evaluated. The tertiary application with 1.2 h EBCT, SS, BOD and COD showed stable concentrations less than 1.3, 1.3 and 6.2 mg/L, respectively. Nitrogen could be nitrified even at 7 degrees suggesting BAF can be used for a water reuse method as well as an effective add-on facility in cold regions. However, BAF was not stable with CSO application at increased flow rates suggesting CSO must be equalised prior to application. Disinfection was necessary even during normal weather conditions.