Effectiveness test of alginate‐derived polymeric surfactants

A series of alginate‐derived polymeric surfactants (APSs) with a linear alkyl group (C8, C12, C16) was synthesized by oxidation followed by reductive amination of 2,3‐dialdehydic alginate. The products were characterized by measuring IR spectra, NMR spectra, surface tension and critical micelle concentration (cmc). They were also tested for the solubilization of azobenzene and adsorption of heavy metal. In the case of 40% CHO‐C8 APSs, the lowest interfacial tension value (31.5 m Nm^?1) was obtained at the cmc value of 1.35 g dm^?3. The dissolving capacity of 40% CHO‐C8 APS towards azobenzene was 27 times greater than that of alginate. The overall cobalt (Co²⁺) removal efficiency by adsorption using APSs was high compared with that of sodium alginate at pH 3, 5 and 7. Equilibrium aspects of cobalt adsorption onto 10% CHO‐APSs were studied, and the results show that APSs had high equilibrium capacities for cobalt uptake, 115.5 mgg^?1. © 2002 Society of Chemical Industry     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Synthesis and characterization of in situ polymerized segmented thermoplastic elastomeric polyurethane/layered silicate clay nanocomposites

Nanocomposites based on thermoplastic elastomeric polyurethane (TPU) and layered silicate clay were prepared by in situ synthesis. The properties of nanocomposites of TPU with unmodified clay were compared with that of organically modified clay. The nanocomposites of the TPU and organomodified clay showed better dispersion and exhibited superior properties. Exfoliation of the clay layers was observed at low organoclay contents, whereas an intercalated morphology was observed at higher clay contents. As one of major purposes of this study, the effect of the silicate layers in the nanocomposites on the order–disorder transition temperature (T_ODT) of the TPU was evaluated from the intensity change of the hydrogen‐bonded and free carbonyl stretching peaks and from the peak position change of the N? H bending peak. The presence of the organoclay increased T_ODT by approximately 10°C, which indicated improved stability in the phase‐separated domain structure. The layered silicate clay caused a tremendous improvement in the stiffness of the TPU; meanwhile, a reduction in the ultimate elongation was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3048–3055, 2006     

Synthesis and non‐isothermal crystallization behavior of poly(ethylene phthalate‐co‐terephthalate)s

A series of poly(ethylene phthalate‐co‐terephthalate)s were synthesized by melt polycondensation of ethylene glycol (EG) with dimethyl phthalate (DMP) and dimethyl terephthalate (DMT) in various proportions. The DMT‐rich polymers were obtained with reasonably high molecular weights, whereas the DMP‐rich polymers were synthesized with relatively low molecular weights due to steric effects associated with the highly kinked DMP monomer. The compositions and thermal properties of the polymers were determined. The copolymers containing DMP in amounts of ≤ 21 mol% were crystallizable, whereas the other polymers were not. All the polymers exhibited a single glass transition temperature. Analysis of the measured glass transition temperatures and crystal melting temperatures confirmed that the DMT‐rich copolymers are random copolymers. The non‐isothermal crystallization behaviors of the DMT‐rich copolymers were investigated by calorimetry and modified Avrami analysis. The Avrami exponents n were found to range from 2.7 to 3.8, suggesting that the copolymers crystallize via a heterogeneous nucleation and spherulitic growth mechanism; that is, the incorporation of DMP units as the minor component does not change the growth mechanism of the copolymers. In addition, the activation energies of the crystallizations of the copolymers were determined; the copolymers were found to have higher activation energies than the PET homopolymer. Polym. Eng. Sci. 44:1682–1691, 2004. © 2004 Society of Plastics Engineers.     

Synthesis of polystyrene/poly(butyl acrylate) core–shell latex and its surface morphology

A polystyrene (PS)/poly(butyl acrylate) (PBA) composite emulsion was produced by seeded emulsion polymerization of butyl acrylate (BA) with PS seed particles which were prepared by emulsifier‐free polymerization of styrene with potassium persulfate (KPS) under a nitrogen atmosphere at 70°C for 24 h with stirring at 60 rpm and swelled with the BA monomer in an ethanol/water medium. The structure of the PS/PBA composite particles was confirmed by the presence of the characteristic absorption band attributed to PS and PBA from FTIR spectra. The particles for pure PS and PS/PBA with a low content of the BA monomer were almost spherical and regular. As the BA monomer content was increased, the particle size of the PS/PBA composite particles became larger, and more golf ball‐like particles were produced. The surface morphology of the PS/PBA composite particles was investigated by AFM and SEM. The T_g's attributed to PS and PBA in the PS/PBA composite particles were found at 110 and ?49°C, respectively. The thermal degradation of the pure PS and PS/PBA composite particles occurred in one and two steps, respectively. With an increasing amount of PBA, the initial thermal decomposition temperature increased. On the contrary the residual weight at 450°C decreased with an increasing amount of PBA. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 595–601, 2003     

Durable antimicrobial treatment of cotton fabrics using N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride and polycarboxylic acids

N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride (HTCC), a water‐soluble chitosan quaternary ammonium derivative, was used as an antimicrobial agent for cotton fabrics. HTCC has a lower minimum inhibition concentration (MIC) against Staphylococcus aureus, Klebsiella pneumoniae, and Escherichia coli compared to that of chitosan; however, the imparted antimicrobial activity is lost on laundering. Thus crosslinking agents were utilized to obtain a durable antimicrobial treatment by immobilizing HTCC. Several crosslinkers such as dimethyloldihydroxyethylene urea (DMDHEU), butanetetracarboxylic acid (BTCA), and citric acid (CA) were used with HTCC to improve the laundering durability of HTCC treatment by covalent bond formation between the crosslinker, HTCC and cellulose. The polycarboxylic acid treatment was superior to the DMDHEU treatment in terms of prolonged antimicrobial activity of the treated cotton after successive laundering. Also, the cotton treated with HTCC and BTCA showed improved durable press properties without excessive deterioration in mechanical strength or whiteness when compared to the citric acid treatment. With the addition of only 0.1% HTCC to BTCA solutions, the treated fabrics showed durable antimicrobial activity up to 20 laundering cycles. The wrinkle recovery angle and strength retention of the treated fabrics were not adversely affected with the addition of HTCC. Therefore, BTCA can be used with HTCC in one bath to impart durability of antimicrobial activity along with durable press properties to cotton fabric. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1567–1572, 2003     

Oil absorbents based on styrene–butadiene rubber

Four oil absorbents based on styrene–butadiene (SBR)—pure SBR (PS), 4‐tert‐butylstyrene–SBR (PBS), EPDM–SBR network (PES), and 4‐tert‐butylstyrene‐EPDM‐SBR (PBES)—were produced from crosslinking polymerization of uncured styrene–butadiene rubber (SBR), 4‐tert‐butylstyrene (tBS), and ethylene–propylene–diene terpolymer (EPDM). The reaction took place in toluene using benzoyl peroxide (BPO) as an initiator. Uncured SBR was used as both a prepolymer and a crosslink agent in this work, and the crosslinked polymer was identified by IR spectroscopy. The oil absorbency of the crosslinked polymer was evaluated with ASTM method F726‐81. The order of maximum oil absorbency was PBES > PBS > PES > PS. The maximum values of oil absorbency of PBES and PBS were 74.0 and 69.5 g/g, respectively. Gel fractions and swelling kinetic constants, however, had opposite sequences. The swelling kinetic constant of PS evaluated by an experimental equation was 49.97 × 10^?2 h^?1. The gel strength parameter, S, the relaxation exponent, n, and the fractal dimension, d_f, of the crosslinked polymer at the pseudo‐critical gel state were determined from oscillatory shear measurements by a dynamic rheometer. The morphologies and light resistance properties of the crosslinked polymers were observed, respectively, with a scanning electron microscope (SEM) and a color difference meter.     

Infrared reflectance and transmission spectra of semiconducting non-stoichiometric CdGe x As2

The infrared reflectance and transmission spectra of amorphous CdGe _x As₂ were investigated to study the amorphous structure with varying Ge content. The mid-infrared optical absorption edges of amorphous CdGe _x As₂ with 0<x<1.2, were observed in the range 1.6–1.7 m, indicating a structural similarity in short-range order throughout. Comparing the reflectance and transmission spectra of amorphous and devitrified crystalline phases established that the structures of amorphous CdGe _x As₂ transformed from the CdAs₂ basic structure to the chalcopyrite (CdGeAs₂) structure, as one progressed fromx=0 tox=1.2. The infrared spectra were interpreted interactively with radial distribution function, magnetic susceptibility, density measurements, and crystallization studies. The crystallization behaviour of amorphous CdGe _x As₂ that was heat treated at different temperatures was investigated using far-infrared transmission spectra.     

Fabrication of high-efficiency anatase TiO2 photocatalysts using electrospinning with ultra-violet treatment

In metal oxide nanofiber fabrication using the electrospinning method, heat treatment is performed at temperatures of 500°C or higher for crystallization and polymer desorption. Therefore, it is difficult to fabricate low-temperature phase metal oxides that crystallize at low temperatures. TiO₂, a representative metal oxide often used as photocatalysts, is known to have higher photocatalytic activity in the low-temperature phase (anatase structure) than in the high-temperature phase (rutile structure). Studies on the fabrication of TiO₂ anatase nanofibers using conventional electrospinning have reported disadvantages such as the partial expression of rutile structures and low crystallinity. This study developed an anatase TiO₂ nanofiber as a high-efficiency catalyst based on the electrospinning method and a residual organic matter cleaning method that employs ultra-violet (UV) light. We fabricated nanofibers using the electrospinning method and implemented TiO₂ nanofibers with the anatase structure through heat treatment at 260°C. Residual organics remaining after heat treatment of the fabricated crystalized TiO₂ nanofibers were removed by exposing them to UV light, thereby improving photocatalytic efficiency. The photocatalytic efficiency of the fabricated TiO₂ nanofibers was confirmed through a methylene blue (MB) decomposition experiment under visible light irradiation. The photocatalytic efficiency (time taken for the concentration of the MB solution to reach 50%) of the UV-treated TiO₂ nanofibers was approximately six times higher than of P25 and the heat-treated nanofibers.     

Temperature and grain size dependence of superplasticity in a Zn−0.3wt.%Al alloy

The superplastic deformation behavior of quasi-single phase Zn-0.3 wt. %Al was investigated. A series of load relaxation and tensile tests was conducted at various temperatures ranging from RT (20 °C) to 200 °C. The recently proposed internal variable theory of structural superplasticity was applied. The flow curves obtained from load relaxation tests were shown to consist of contributions from interface sliding (IS) and accommodating plastic deformation. In the case of quasi-single phase Zn-0.3 wt.% Al alloy with an average agrain size of 1 μm, the IS behavior could be described as a viscous flow process characterized by a power index of M_g=0.5. A large elongation of about 1400% was obtained at room temperature and the strain rate sensitivity parameter was about 0.4. Although relatively large-grained (10 μm) single phase alloy showed a high value of strain rate sensitivity comparable to that of fine-grained alloy at very low strain rate range, IS was not expected from the analysis based on the internal variable theory of structural superplasticity at room temperature. As the temperature increased above 100 °C, however, the contribution from IS was observed at a very low strain rate range. A high elongation of ∼400% was obtained in a specimen of 10-μm-grain-size at 200 °C under a strain rate of 2×10⁻⁴/sec. Jointly appointed at Center for Advanced Aerospace Materials (CAAM)