Hydrothermal Reaction Mechanism and Pathway for the Formation of K2Ti6O13 Nanowires

Calculations and detailed first principle and thermodynamic analyses have been performed to understand the formation mechanism of K₂Ti₆O₁₃ nanowires (NWs) by a hydrothermal reaction between bulk Na₂Ti₃O₇ crystals and a KOH solution. It is found that direct ion exchange between K⁺ and Na⁺ plus H⁺ interactions with [TiO₆] octahedra in Na₂Ti₃O₇ promote the formation of an intermediate H₂K₂Ti₆O₁₄ phase. The large lattice mismatch between this intermediate phase and the bulk Na₂Ti₃O₇ structure, and the large energy reduction associated with the formation of this intermediate phase, drive the splitting of the bulk crystal into H₂K₂Ti₆O₁₄ NWs. However, these NWs are not stable because of large [TiO₆] octahedra distortion and are subject to a dehydration process, which results in uniform K₂Ti₆O₁₃ NWs with narrowly distributed diameters of around 10 nm.     

Structural and Superconducting Property Variations with Nominal Mg Non‐Stoichiometry in MgxB2 and Its Enhancement of Upper Critical Field

By applying a combination of characterisation tools, changes in structural and superconducting properties with nominal Mg non‐stoichiometry in Mg_xB₂ are found. The non‐stoichiometry produces enhanced in‐field critical current densities (J_c's) and upper critical field / irreversibility field (H_c2/H_irr(T)) values. Upper critical fields of ～ 21 T (4.2 K) were obtained in nominal Mg‐deficient samples compared to ～ 17 T (4.2 K) for near‐stoichiometric samples.     

Performance evaluation of a water/silicone oil two‐phase partitioning bioreactor using Rhodococcus erythropolis T902.1 to remove volatile organic compounds from gaseous effluents

BACKGROUND: In the framework of biological processes used for waste gas treatment, the impact of the inoculum size on the start‐up performance needs to be better evaluated. Moreover, only a few studies have investigated the behaviour of elimination capacity and biomass viability in a two‐phase partitioning bioreactor (TPPB) used for waste gas treatment. Lastly, the impact of ethanol as a co‐substrate remains misunderstood. RESULTS: Firstly, no benefit of inoculation with a high cellular density (>1.5 g L^?1) was observed in terms of start‐up performance. Secondly, the TPPB was monitored for 38 days to characterise its behaviour under several operational conditions. The removal efficiency remained above 63% for an inlet concentration of 7 g isopropylbenzene (IPB) m^?3 and at some time points reached 92% during an intermittent loading phase (10 h day^?1), corresponding to a mean elimination capacity of 4 × 10^?3 g L^?1 min^?1 (240 g m^?3 h^?1) for a mean IPB inlet load of 6.19 × 10^?3 g L^?1 min^?1 (390 g m^?3 h^?1). Under continuous IPB loading, the performance of the TPPB declined, but the period of biomass acclimatisation to this operational condition was shorter than 5 days. The biomass grew to approximately 10 g L^?1 but the cellular viability changed greatly during the experiment, suggesting an endorespiration phenomenon in the bioreactor. It was also shown that simultaneous degradation of IPB and ethanol occurred, suggesting that ethanol improves the biodegradation process without causing oxygen depletion. CONCLUSION: A water/silicone oil TPPB with ethanol as co‐substrate allowed the removal of a high inlet load of IPB during an experiment lasting 38 days. Copyright © 2008 Society of Chemical Industry     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

行波管放大器相位噪声的分析及其抑制

主要分析规则调相信号对行波管放大器频谱纯度的影响,并且根据行波管放大器相位噪声产生的过程和原因,提出两种抑制相位噪声的方法.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Optimal and self‐tuning fusion Kalman filters for discrete‐time stochastic singular systems

Based on the optimal fusion estimation algorithm weighted by scalars in the linear minimum variance sense, a distributed optimal fusion Kalman filter weighted by scalars is presented for discrete‐time stochastic singular systems with multiple sensors and correlated noises. A cross‐covariance matrix of filtering errors between any two sensors is derived. When the noise statistical information is unknown, a distributed identification approach is presented based on correlation functions and the weighted average method. Further, a distributed self‐tuning fusion filter is given, which includes two stage fusions where the first‐stage fusion is used to identify the noise covariance and the second‐stage fusion is used to obtain the fusion state filter. A simulation verifies the effectiveness of the proposed algorithm. Copyright © 2008 John Wiley & Sons, Ltd.     

硫酸钙氨法制取硫酸钾新工艺的实验研究

利用K2 +2 ,Ca2 +/ /SO2 -4 ,Cl2 -2 ,NH3—H2 O混合体系相图作为工艺指导 ,进行硫酸钙制取硫酸钾工艺的相图研究和分析 ,确定实验优选因素及水平并进行正交实验 ,根据实验结果进行极差分析 ,得出新的结论。合适的工艺条件为 :氨浓度为 40 % ,配料比n( 2KCl) :n(CaSO4 ·2H2 O)为 1:1,反应温度为 5℃ ,反应时间为 1h。     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Note on ‘Construction of Double Sampling s‐Control Charts for Agile Manufacturing’

He and Grigoryan (Quality and Reliability Engineering International 2002; 18 :343–355) formulated the design of a double‐sampling (DS) s control chart as an optimization problem and solved it with a genetic algorithm. They concluded that the DS s control charts can be a more economically preferable alternative in detecting small shifts than traditional s control charts. We explain that, since they only considered the average sample size when the process is in control, their conclusion is questionable. Copyright © 2006 John Wiley & Sons, Ltd.