Fe3Al/Q235异种材料扩散焊界面相结构分析

采用X射线衍射、透射电镜和电子衍射技术对Fe3Al/Q235真空扩散焊界面附近的微观相结构进行了试验研究。试验结果表明，当加热温度1050～1080℃，保温时间60min，压力9.8MPa时，Fe3Al金属间化合物与Q235钢扩散焊界面附近形成了明显的扩散过滤区，该过渡区由Fe3Al相和a-Fe(Al）固深体构成，显微硬度约为480～540HM，不存在含铝校较高的高硬度脆性相。有利于提高Fe3Al/Q235扩散过滤区的韧性，提高扩散焊接头的抗裂纹能力。扩散过滤区中的Fe3Al相与a-Fe(Al）固溶体之间存在着（110）a-Fe(Al)//(011)Fe3Al和[001]a-Fe(Al)//[100]Fe3Al的晶体学取向关系。     

Study of the polymerization of 1-octadecene with different rnetallocene catalysts

Summary 1-Octadecene (C18) was polymerized by using different metallocene catalysts. The rac-Et(Ind)₂ZrC1₂/MAO (I) and rac-Me₂Si(Ind)₂ZrC1₂/MAO (III) presented the highest activity as compared with ra-Et(2-Me-Ind)₂ZrCl₂/MAO (II) and Ph₂C(Flu)(Cp)ZrC1₂/MAO (IV) catalysts. Catalyst IV produced polymers with highest molecular weights. The microstructure of the polymers was determined by ¹³C-NMR spectroscopy. Catalyst systems I, II and III produced isotactic polymers while catalyst IV produced polymers with mainly syndiotactic structures but with large amount of stereoregular error. Received: 21 June 2002/Revised version: 4 November 2002/ Accepted: 4 November 2002     

AA/AAm改性的PVF高速粘贴标签胶粘剂的研制

采用AA/AAm改性PVF的方法制备高速粘贴标签胶粘剂。对PVA用量、聚合反应温度、引发剂、pH值、AA/AAm等对胶粘剂性能的影响进行了研究。结果表明 ,这些因素对胶粘剂的粘度、稳定性、干燥速度和粘贴强度有很大的影响。该胶粘剂有较好的粘贴性能 ,适用于 14 0 0 0 -2 80 0 0支 /小时高速啤酒生产线粘贴标签     

Isobaric vapor—liquid equilibria for binary systems composed of methyl butanoate with ethanol and with propan-1-ol at 114.66 and 127.99 kpa

Vapor-liquid equilibrium data for the binary systems methyl butanoate/ethanol and methyl butanoate/propan-l-ol at pressures of 114.66 and 127.99 kPa are presented. Both mixtures yield an azeotrope, the compositions (ester) of which decrease quasi-linearly as the pressure increases. The experimental data for all the binary mixtures were fitted to a suitable equation and then used for comparison with predictions by ASOG and UNIFAC methods. These group contribution models give a good estimation of activity coefficients with an overall mean error less than 5% for all cases.     

锌-锰合金镀层磷化工艺研究

为进一步提高Zn-M n合金镀层的抗蚀性,采用锌锰系磷化处理Zn-M n合金镀层,研究表明在相同镀层厚度下,Zn-M n合金镀层抗蚀能力是镀锌层的5倍,经磷化后的Zn-M n合金镀层的抗蚀能力是镀锌层的7~8倍。实验结果表明,Zn-M n合金镀层经锌锰系磷化后抗蚀性明显提高。     

含水量对渠道保温板保温耐久性的影响及保温板厚度设计

北方渠道大多使用保温板防止混凝土衬砌受冻胀破坏。在计算保温板厚度时为了降低成本,容易忽略保温板使用过程中受各种因素的影响导致保温效果变差的情况,使混凝土衬砌达不到设计使用年限便提前被破坏。内蒙古河套灌区试验结果表明,由于受酸雨、冻融作用、含水量等因素的影响,保温板保温效果平均每年降低0.9℃,其中受含水量变化的影响最大。经试验测得:聚苯乙烯保温板(EPS)含水量每增加1%,会导致导热系数增大5%。基于多层材料串联热阻叠加原理和热阻等效原理,对保温板厚度计算公式进行完善,并提出相应的铺设方法和施工技术要求。该设计对保温板在季节性冻土区的推广应用具有一定参考价值。     

非水溶剂回滴法测定低镍甲烷化催化剂的表面酸性

本文采用非水溶剂回滴法测定了低镍甲烷化催化剂和载体γ—Al2O3的表面酸性，并与催化剂的活性、组成、比表面积关联。实验结果说明，助剂的种类、含量对表面酸性有明显影响，催化剂催化活性与表面酸性关系不大。     

塑胶漆用的聚醚聚氨酯预聚物的研制

以TDT、TMP、N-220、3010、为主要原料合成聚醚型聚氨酯预聚物，达到塑胶漆的性能要求。本文探讨了不同的合成条件对预聚物的影响。     

用酰胺缩醛合成1,4,7,10-四氮杂十二烷的研究

用甲苯作溶剂,使三乙烯四胺和N,N-二甲基甲酰胺二甲基缩醛在85℃反应2h,得到中间体双咪唑啉,产率90.4%,在乙腈溶剂中,碳酸钾存在下,双咪唑啉和1,2-二溴乙烷进行扩环反应,得到环状中间体一溴盐,产率78.7%,一溴盐经碱性水解2h,得到1,4,7,10-四氮杂十二烷,产率74.2%。用元素分析、质谱和核磁共振氢谱对目标化合物进行了表征。     

Detection of beeswax adulterations using concentration guide‐values

The concentrations of 102 chemical compounds (saturated and unsaturated hydrocarbons, palmitates, total and free acids, total hydroxyacids, total and free alcohols, acidic monoesters and monoesterified 1,2,3‐propanetriols) have been determined by GC/FID on white and yellow comb beeswax of Apis mellifera from different regions of Spain. Guide‐value ranges are proposed for its characterization and to discriminate adulterated foundation beeswax sheets. The concentrations of many compounds resulted to be statistically different for white and yellow beeswaxes, while the observation of concentrations out of normal in some marketed foundation beeswax sheets suggested their adulteration. However, the measurement of anomalous concentrations in foundation beeswax sheets did not imply necessarily their rejection by the bees.