采用区内C／I平衡的多区峰窝CDMA系统下行链路的性能

本文对采用区内Ｃ／Ｉ平衡的多区蜂窝ＣＤＭＡ系统下行链路的性能进行分析，给出两种区内Ｃ／Ｉ平衡算法并比较它们的性能，考虑呈对数正态分布的阴影和Ｒ＾－４规律的路径损失的综合影响，采用与传统不同的小区平均中断概率来评价系统的性能。     

锗γ能谱测量中的符合相加修正

本文介绍了锗γ能谱测量中符合相加修正的原理和方法,给出了修正公式。分别计算了不同几何条件下两个锗探测器对一些放射性核素的符合相加修正因子,估计了符合相加修正因子对活度测量结果的误差贡献。     

加氢裂化热高分油管线弯头开裂分析

对国产加氢裂化热高分油管线的弯头开裂原因进行了分析 ,对预防连多硫酸腐蚀提出了相应的防范措施 :选用碳含量 <0 .0 3 %并含有稳定化元素Ti、Nb的奥氏体不锈钢或双相钢 ;控制焊缝硬度不大于HB2 0 0并焊后热处理 ;12CrMo和 15CrMo耐应力腐蚀性能好 ;设备停运后马上进行清洗并用碱液中和     

Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

The corrosion behavior of sputter-deposited aluminum-tungsten alloys

Thin films on aluminum-tungsten alloys were prepared by co-deposition of pure aluminum and pure tungsten, each sputtered by an independently controlled magnetron source, on glass and sapphire substrates. Completely amorphous films were obtained in the Al₈₀W₂₀-Al₆₇W₃₃ composition range. Passivity and corrosion behavior of amorphous Al-W alloys were investigated in 1 M deaerated hydrochloric acid solution using polarization and impedance spectroscopy measurements and have been correlated with the properties of pure alloy components. Tungsten and sputter-deposited Al-W thin films are inherently passive materials while aluminum undergoes pitting corrosion in hydrochloric acid solution. The passive film formed at the OCP on each alloy possesses excellent electric and dielectric properties comparable to those of the isolating film on tungsten. The absolute impedance increases with increasing tungsten content in the alloy. According to electrochemical polarization measurements, alloying Al with W in solid solution significantly enhances the material's resistance to pitting corrosion by shifting the breakdown potential above 2000 mV (Al₆₇W₃₃) and lowering the corrosion rate at the OCP by more than two orders of magnitude. The most likely mechanism explaining the passivity of amorphous Al-W alloys, the Solute Vacancy Interaction Model (SVIM), involves the formation of complexes between highly oxidized solute atoms (W⁺⁶) and mobile cation vacancies, which restrict the transport of Cl⁻ through the oxide film and inhibit its breakdown in hydrochloric acid solution. The role that film stress relaxation effects and microscopic defects in amorphous Al-W films, of the some composition, and deposited on various substrates play in their corrosion resistance is discussed.     

胜利原油350～510℃馏分糠醛精制的研究

对胜利原油 350～ 510℃馏分每 4 0℃切割一种馏分进行糠醛精制 ,考察了实验室条件下不同温度、不同醛油比条件下精制对提余油质量和收率的影响。采用醛油比 3× 1∶1,抽提温度在 70～ 95℃ ,可使精制馏分油粘度指数提高 10～ 2 7个单位 ,精制油收率高于 70 %。